00-Clutch Installation

Рет қаралды 146,136

9 жыл бұрын

00:38-Step 1-Inspect Electrical Circuit
02:12-Step 2-Remove Tie Wraps and Inspect the Wire Harness
02:43-Step 3-Remove the Belt
03:14-Step 4-Note Component Locations
05:00-Step 5-Note Clutch Orientation
05:11-Step 6-Remove Clutch
05:26-Step 7-Inspect & Clean Crankshaft
06:55-Step 8-Install the Drive Pulley and Spacers
07:18-Step 9-Install the New Clutch
08:27-Step 10-Install the Clutch Bolt
08:44-Step 11-Torque Clutch Bolt
09:58-Step 12-Install the Deck Belt
10:06-Step 13-Inspect the Clutch Anti-Rotation Device
10:45-Step 14-Connect the Clutch wire & Secure with Tie Wraps
13:02-Step 15-Torque Blades
13:14-Step 16-Burnish The Clutch

Пікірлер: 35

@mvintrigue-trawlerdiy1101 7 жыл бұрын

I just installed one of these on a John Deere Z920A. Product looked good. Install was without issue and I did the run is procedure tonight and it seems to kick in nice and firm. Will mow tomorrow and then update.

@davekana8388 4 жыл бұрын

Thanks for the how to on the DC draw and burnishing the clutch! This Xtreme PTO should outlast my 15 year old Cub Cadet LT2180. It’s good to know we can still buy quality!

@physicsramble 2 жыл бұрын

Thanks for the heads up about checking the voltage, mine was high, and replacing the battery fixed it. Would have been sad if I'd ignored it and burned up the new clutch.

@mulonru2965 4 жыл бұрын

Thanks I needed this information

@phillipnesbitt8720 3 жыл бұрын

Nice video best auto vid I've seen in years thanks

@johnc6157 4 ай бұрын

WELL PRESENTED. Thank you.

@rodneyrimmer1435 6 жыл бұрын

Good morning, I have a question on removing the PTO clutch. When I try to remove the bolt the shaft turns. What is the best way to secure the shaft so I can remove the bolt and then torque to correct ft. lb. when installing. (2000 Huskee riding mower)Thanks

@andycapp8843 5 жыл бұрын

At 4.12 I fell asleep, my apologies. I thought, mistakenly, the video was about installation, not an introduction to procedures necessary before starting any mechanical job. When my eyes opened I looked at the comments, none of which received the courtesy of a reply, I realised I had missed nothing at all.

@elmeromero1794 7 жыл бұрын

Hello I just ordered a PTO clutch from your website for my Cub cadet rzt 42. How do you guys pull old clutch out?

@orange13 7 жыл бұрын

very informative video, thanks. But you are mixing up voltage and current at the beginning of the video. These 2 things are not interchangeable

@markchidester6239 Жыл бұрын

Excellent video You sold me Wish you had a link to your website

@richardwarren5988 6 жыл бұрын

Should my clutch be loose, it seems to vibrates when idiling

@glenparks5175 3 жыл бұрын

Yea try one that's totally fn seezzed up on the shaft and comes apart if fn pieces

@gardnerraffa5970 7 жыл бұрын

I have a toro Z420 new clutch in but need to replace electrical wires with new pigtail you provided. Do wires need to be connected in a certain way or will clutch work either way the wires are connected to original wiring harness

@Spinnaker617 4 жыл бұрын

Same here. They sent the wrong adapter harness for my Husqvarna. I need to know on their plug from the clutch which wire is positive. This is no help.

@aaronclark1599 Жыл бұрын

Do you have a video on how to change the rotation?

@wcjcnc 3 жыл бұрын

No mention of how to keep the crankshaft from turning while torquing the crankshaft bolt

@catbirdfeeder 2 жыл бұрын

at 5:111 he talks about using an impact wrench or HOLD THE D-Spacer to prevent the engine crankshaft from turning. however not all have D-Spacers...i saw one guy use a pipewrench to hold it

@wcjcnc 2 жыл бұрын

@@catbirdfeeder You only use an impact wrench to remove the crankshaft bolt. When you install the clutch you use a torque wrench. There is actually a wrench made to hold the spacer but it’s expensive so I custom made one identical to the one you can buy.

@Romans--bo7br Жыл бұрын

WCJCNC..... being an "Old Schooler" myself... just remove the spark plug, and feed some rope into the cylinder, then rotate the piston up towards TDC, and it will "lock up" there and will Not rotate any further. When you're finished with torquing the crankshaft bolt, rotate the crankshaft in the opposite direction, enough to free up the rope, and pull it out by the "tail" you left hanging out of the plug hole, then reinstall the plug again... to the correct torque specs for your engine (especially if has an aluminum head(s)), of course.

@Rsenior1981 6 жыл бұрын

I appreciate the effort for this video, but it is no extra help beyond the manual. You should show an actual installation.

@user-oz4jb6lq2g 8 ай бұрын

The DC voltage coming from my battery at full throttle is 14.40 VDC. What can I do to reduce this to meet the 14 VDC max?

@TheAlienBeard 5 жыл бұрын

Waist of time if looking for someone installing!

@crewmax4240 6 жыл бұрын

Too bad there are no responses to these questions.

@randybeard6040 5 жыл бұрын

As Cable Man Says--Get Ur Done Already....

@timeless6964 5 жыл бұрын

I See, Nobody Got ANY Answers???........WTF??

@fair2middlin 2 жыл бұрын

ZZZzzzz. Many people are putting these on their mowers, not their tables

@mojejoe 4 жыл бұрын

Wow...create a how to video and never address any questions...do you guys even go back to these videos...

@hairycods2273 2 жыл бұрын

No they are very busy diddling the hole they sit on & challenging each other to see who can shove there tongue six inches up the other ones a** h*** & if they can still fart the star spangled banner while said tongue is bottomed out in ones box

@tcmits3699 22 күн бұрын

Best thing l ever did was get rid of this ridiculous type of clutch, and made a simple linkage with idler. Now beautiful,smooth engagement. Good riddance 😂NOT