@tylerheffernan3498 Жыл бұрын
I usually run the drill in reverse for a few turns before unchucking. After a few you'll get the feel for how much to reverse to avoid the spring back. If you do it right, the twisted wire will come out of the drill and not untwist at all. This is coming from 15 years in the car audio and security world and tens thousands of twisted wires.
@AutodromoF1 Жыл бұрын
Thank you for this, especially the tip about spring back. I’m gonna do this to the signal wires of the maf on my car, plus shield and ground the shield. Idk if it’s all the extra radio waves now that was giving making it read erratic but twisting and shielding worked in my temporary fix i did.
@isaackivah 17 күн бұрын
Genius. Thank you sir
@meh7517 6 жыл бұрын
Hey man excellent video this really helped me out, just some advice it'd be nice to see multiple different ways to secure the wire that you're twisting. Depending on the equipment, or extra sets of hands the different variations of securing the opposite end you're twisting down.
@Jorokusaki 3 жыл бұрын
Cool thanks! Been looking for techniques to apply to jewelry making!
@user-wz4rk3mh1p 5 жыл бұрын
Can't wait for giving it a try! It appears to save me lots of time...
@apal1257 4 жыл бұрын
Great tip for my jewelry wire. Thanks.
@J.D_YT 4 жыл бұрын
Works for speaker wire great
@shaungutierrez9411 11 ай бұрын
If you run the wire between your fingers as you did before releasing from the drill chuck with maintained tension (wire taut), a few times from end to end... then the wire will form straight. Of course, slowly release. It should not tangle up.
@vosborne945 3 жыл бұрын
I tried it with silicone covered 16 gauge and had snapback every time.
@rjc0234 6 жыл бұрын
Thanks for the great tip! I hope i don't forget
@cr4bee 3 жыл бұрын
Here’s a reminder for ya in case ya forgot
@rjc0234 3 жыл бұрын
@@cr4bee Thanks! Thankfully this is one that has stuck with me, and i regularly use it on my electrical projects!
@jamesh1758 8 ай бұрын
Why did I google this after twisting 2m by hand. Took forever
@abhijitganu7771 3 жыл бұрын
What is wire length reduction after twisting? If I want 10 feet twisted wire how to know length of wire before twisting
@torresgonzalezdiego 10 жыл бұрын
More vídeos please!
@shawn576 6 жыл бұрын
Good to know. Thanks!
@tubefictitious 4 жыл бұрын
Very helpful, just what I was looking for. Can I ask what you attached the unseen ends of the wire to? Thanks!
@kilgoretrout5456 Жыл бұрын
A vice works best.
@ryanb1874 4 жыл бұрын
Can someone come up with a drill hack to cross grade 2 or more wires to end up with cylindrical mesh, that would be great...
@harryniedecken5321 4 ай бұрын
How would you make 200 ft though, that is my goal.
@MoparGuy1625 6 жыл бұрын
Is that safe to do? Like no issues? I like the look. Looks cleaner but don’t want to cause any issues. I’m sure over twisting could be problematic
@TempoDrift1480 5 жыл бұрын
MOPARGuy Well you can't be stupid about it, it's not any different than driving a car or snorting cocaine. Just pay attention and don't fuck it up.
@SynZ777 3 жыл бұрын
@@TempoDrift1480 I like the way you think.
@leeguitarmcr 2 жыл бұрын
How are you fixing the wire to the tension point?
@godsballroom5298 5 жыл бұрын
Can I do 4 at a time or only 2!!
@besarazemi6541 5 жыл бұрын
As much as a drill can fit
@gaojing9072 8 жыл бұрын
what is the brand of this tool ?
@waheed002 3 ай бұрын
⁰
Cool Items Official
Рет қаралды 43 МЛН
CbyS Paracord and More
Рет қаралды 57 М.
Creation Holic
Рет қаралды 6 МЛН
UWOODWORKER
Рет қаралды 803 М.
Cool Items Official
Рет қаралды 43 МЛН