@cabbyhubby 2 жыл бұрын
Gotta love a young man in his driveway doing his own mechanic work ... way to go 👍
@matapeas4302 5 жыл бұрын
ok,he did a good job,the only regular person doing leaf spring set up,i was surprised to see the spring differences side to side,thats what I was looking for.also add a leafs add 1.5 to 3 inches of lift,all depends on add a leaf spring you get and wear of your leaf springs.good job homie,thumbs up,do more videos,were all not perfect but unless someone makes a mistake while doing something well never know what to look out for.
@justinpitts3640 5 жыл бұрын
Can u make a video of the truck after the lift
@robertpoirier8520 3 жыл бұрын
Excellent work! How’s it going so far? You are so on it about squeaks. Any squeaks with the dry lube thus far?
@memefpv 3 жыл бұрын
No squeaks, no issues. Sank maybe a 1/4in after 6 months.
@keithwheeler9796 6 жыл бұрын
Gotchya😉
@HealthSupercharger 6 жыл бұрын
Will this also work on 2011 Frontier pickup? My suspension is sitting low in the back and when i fill the bed level with compost cow manuer it sits almost on the bumpers. I would love to be able to carry extra few hundred pounds or be sitting higher. My pickup is just the stock model so I do not know if the axel and bearings are heavy duty enough for 1500lb load.
@memefpv 6 жыл бұрын
HealthSupercharger Definitely doable for your frontier. Same exact setup, same exact parts haha.
@davidsamis281 6 жыл бұрын
Too much wind. Could not hear him on a lot of peices. And he said no matter what don't forget (wind).
@dennisfossey4312 2 жыл бұрын
What was the spray you were using to stop the squeaks?
@memefpv 2 жыл бұрын
I want to say it's WD 40 branded dry lube
@reyesromero466 4 жыл бұрын
Dude holding the channel locks backwards
@Agent.K. 4 жыл бұрын
Did you need new U-bolts?
@memefpv 3 жыл бұрын
It is always recommended to use new Ubolts to ensure the threads are tight, rather safe than sorry
@RobPerez-Pinchel 5 жыл бұрын
Did you cut the new pin down?
@memefpv 5 жыл бұрын
Rob Perez the new center pin fit well enough without trimming, thanks to the AAL, but without it might’ve needed a bit. the U Bolts needed trim
@RobPerez-Pinchel 5 жыл бұрын
@@memefpv Stock ubolts needed trimming?
@RobPerez-Pinchel 5 жыл бұрын
@@memefpv nevermind, I have a 2004 Xterra
@gaborkertesz6019 6 жыл бұрын
How much overall lift did you get out of this mod ?
@memefpv 6 жыл бұрын
being an 07, i was sagging almost a inch and a half. so adding brand new leafs added that back. add the AAL and i got about 2.5 ovedall
@gaborkertesz6019 6 жыл бұрын
Did you need longer U-bolts to reinstall ? Or anything else that doesn't come with the leaves ?
@memefpv 6 жыл бұрын
Gabor Kertesz I purchased long U bolts from Auto Zone or one the chains, i used those and cut a little off the ends because they stuck farther out of the bottom plate.
@keithwheeler9796 6 жыл бұрын
WD-40 is a drying agent
@memefpv 6 жыл бұрын
Keith Wheeler Thanks, I was using WD-40 Dry Lubricant. Not regular WD-40
@bc2002bc 2 жыл бұрын
dude! the wind is effing with your mic... I can't hear a frigging word... im a newbie that needs to hear the instructions and I can't hear anything
@memefpv 2 жыл бұрын
Want me to remake the whole video, 6 years later? Lmao I was 17, don't even have the truck anymore. AFAIK, this is the best video you got specific to an Xterra, which is why I made it.
@Texelectric 2 жыл бұрын
@@memefpv Looks perfectly fine to me, don't even need to hear you, just gotta see what you're doing and that's all we needed. Thank you!
KnightWheels
Рет қаралды 63 М.