this video will help people trying to know how it is to replace the lenses from a BMW X5 e70. from removing the fender trims to heat and disassemble the headlight itself for a new lease to be put on. and a better look on you car.
Пікірлер: 83
@dljunior2852 Жыл бұрын
Very good explanation and demonstration. I will consider doing my own since watching you.
@thebudgetpro8181 Жыл бұрын
Thanks for watching and sure you will get it done. First is a little harder but on the second one goes easier.
@joshhansan-bj6ju2 ай бұрын
You have shown the best way of taking the X5 headlight out. Thank you very much my friend.❤👍👍👍
@BMWBoyeeM33 жыл бұрын
Great job man. Thanks for the commentary as well.
@stephenmifsud2998 Жыл бұрын
Thanks for a very helpful video. Would never have managed without.
@josemario160610 ай бұрын
This is the best video I've find on this. Thanks! Easiest and fastest way.
@levkarpets33293 жыл бұрын
Best way to remove lens from headlight is put it in the box and use hairdryer to create a heat box and then the headlight you heart equally everywhere and you just pull the length of and that’s it
@MrZylot2 ай бұрын
А что за коробка должна быть, если надо нагреть до 150 градусов
@GrowthGuided3 жыл бұрын
Headlights look great. Thanks so much for putting this video up !!
@briandeguzman6496 Жыл бұрын
Great vid, thanks for sharing!
@brianpleysier77493 жыл бұрын
Thank you very much for this video mate. Really helped me replace one of my lenses. Gotta say....pr&@k of a job but rewarding. Glad I only needed to do one!
@thebudgetpro81813 жыл бұрын
I am glad it was helpful. hope you don't have to do the other one any time soon. thanks for watching
@allstellar3 жыл бұрын
The best e70 tutorial on the web! Thank you
@thebudgetpro81813 жыл бұрын
Thanks for watching! 😀
@Porky4610 ай бұрын
I put them in oven with 60 degrees... easy to disasamble... and be quick .. the glue is Soft and you need only some New one... and seals well again... takes 3 minutes when it is warm out of the oven
@mariusvasile92383 ай бұрын
Great Job!
@baagiiganbayar8303 жыл бұрын
Thanks bro i got lot of information from you.
@thebudgetpro81813 жыл бұрын
I am glad it help 👍 thanks for watching
@Djsatile3 жыл бұрын
Best one u deserve more subscription
@thebudgetpro81813 жыл бұрын
thanks!
@leealtman5 ай бұрын
excelente tutorial.... thanks!!!
@abro95983 жыл бұрын
Thx! Sincerely Napoleon Dynamite.
@MayraMartinez-iy5th3 жыл бұрын
👍 nice job!
@thebudgetpro81813 жыл бұрын
Thanks! 👍
@santiagoperez2302 жыл бұрын
Nice video thanks
@rolandoromero8836 Жыл бұрын
superb job.
@luvpoems4u Жыл бұрын
Great job!
@Comedyislandwilly10 ай бұрын
Just done my range rover ones today piece of cake same in oven 70 for 20 just used some screw fix silocane lasted years still on BMW
@Turristo08273 жыл бұрын
Help me a lot, thanks amigo
@thebudgetpro81813 жыл бұрын
Vlad Vasilivich glad it help . Working on making the review video after a couple months with rain and all that. Thanks for watching
@atiqulny Жыл бұрын
Hi, you gave me the courage to start thinking to replace the lenses myself. Please share link to this product. I need a set. Thanks!
@josecarlosdelacal58062 ай бұрын
Te felicito por el video !! que tulipas son las que recomiendas comprar de calidad ? y donde ? un saludo
@albernarddagudag38962 жыл бұрын
Thanks for sharing this video. Awesome job you did. By the way, where did you buy your X6 lenses from?
@shannonjames2095 Жыл бұрын
Its an X5 lens and you can get them on eBay
@sahraoui88802 жыл бұрын
👍🏼
@farshidolumi2 жыл бұрын
Hi. Thanks for the great video. What is the brand of the plastic lens cover? Please recommend
@thebudgetpro81812 жыл бұрын
Ill be honest i was kind of on a budget i just try to find the cheapest ones on ebay based on reviews. When i bought the they were like $120 dollars pair. now i think you can get them for like $70 dollars pair
@alandelucis84683 жыл бұрын
hi, congratulations on your tutorial, you did a great job! i would like to do it on my car too .. i wanted to ask you what kind of glue did you use to seal the headlight .. if you can give me the product description ..
@thebudgetpro81813 жыл бұрын
Thnk you very much and thanks for watching. I used a weather strip adhesive from oreylis autoparts. Here is the link www.oreillyauto.com/detail/c/3m/paint---body-repair/sealers---adhesives/weatherstripping-adhesive/f40c64ea76c2/3m-5-ounce-weatherstrip-adhesive/mmm0/08008?q=weatherstripping+adhesive&pos=0
@alandelucis84683 жыл бұрын
@@thebudgetpro8181 hello, sorry if I still disturb you, but the link you put is no longer valid .. the product is not indicated .. then you don't write me the name of the product .. and the company that produces it .. a greeting Alan.
@thebudgetpro81813 жыл бұрын
Oh dont worry and sorry i thought it was working (3M is the brand) And its called (Black super weatherstrip and gasket adhesive)
@alandelucis84683 жыл бұрын
@@thebudgetpro8181 I found it perfect, many thanks! you have been of great help to me 👍 I will keep watching your beautiful videos👍 Greetings Alan.
@designagency18593 жыл бұрын
Nice job and detailed info. Just wondering how long it took for each side?
@thebudgetpro81813 жыл бұрын
Design Agency thanks for the support! well I'll be honest driver side which I did first took one full day just because I have never work on bmw cars so I was being careful not to break things and figuring out what to take off. Then passenger side prob took me 3 to 4 hours. If you have more questions let me know. 👍
@designagency18593 жыл бұрын
@@thebudgetpro8181 Thanks for quick reply. It's really a nice video.
@Comedyislandwilly10 ай бұрын
I just put mine in oven for 20 mins on 70 degrees and they came off no problem.
@joseruiz68473 жыл бұрын
when you say you should have bought some glue from amazon, which glue are you referring to?
@thebudgetpro81813 жыл бұрын
Jose Ruiz it a roll of (butyl glue) it's cheap and more design for headlight retrofit. You can warm it up and reused it on the headlight.
@andres11marin222 жыл бұрын
Does someone has a list of sockets & tools I need to do the job?
@Alig54363 жыл бұрын
How did the glue hold up? Any condensation after install?
@thebudgetpro81813 жыл бұрын
BavarianConnect the weather strip glue is working good so far. I have wash the car several times and no condensation. I'll keep update as we start getting rain here in California.
@mohammedjalloh60652 жыл бұрын
A JOB WELL DONE, WHAT STATE ARE YOU AND I HAVE THE SAME VEHICLE AND AM LOOKING FOR SOMEONE TO INSTALL MINE'S WITH CAUTION AND PROFESSIONALISM. THANKS IN ADVANCE!
@thebudgetpro81812 жыл бұрын
thanks for watching! and I am located in California
@mhxauto3 жыл бұрын
Where did you bought the lenses from? Thanks.
@thebudgetpro81813 жыл бұрын
I bought them on amazon. Just type ( bmw e70 lenses ) and a lot will pop up. I don't have a link for the specific seller I got them from but I just tried to get the cheapest ones and didn't have any issues with fitment.
@mhxauto3 жыл бұрын
@@thebudgetpro8181 Thank you for your reply. I wonder if you recommend specific glue to be used as well?
@thebudgetpro81813 жыл бұрын
mpatxd Yes actually have some comments about that. I would recommend the butyl glue it will come in a roll. The advantage of that glue is that it is easier to work with you put it on you headlight heat it up and it will stick making good seal. The weather strip glue I used I bought it on oreilys for like 8 bucks and only use like half of it and haven't have condensation issues. Hope my responses are helpful.
@OsitoPanda3 жыл бұрын
www.ebay.com/itm/273395544625
@bluegables Жыл бұрын
Where did you buy these len covers? I have a 07 X5 4.8i really bad.
@thebudgetpro8181 Жыл бұрын
I bough them from ebay or amazon ill be hones and i try to get the cheapest ones. But i guess they were all around the same price. Mine fit perfectly but keep in mind all the glue and stuff wont be visible so you will be ok even if they dont fit perfectly glue will go the job.
@KokoupaulGumedzoe-uq4uy11 ай бұрын
Comment mote ampoule phare pour la b m w X5
@cochise1852 жыл бұрын
Hi, Was the driver side more difficult? can you link the video for that side?
@thebudgetpro81812 жыл бұрын
They will be pretty much the same thing except that on the passenger side you habe the the wiper water canister. Wich makes it a little dificult to take off
@cochise1852 жыл бұрын
@@thebudgetpro8181 Thanks! it sounds doable tho....is the washer reservoir hard to remove?
@thebudgetpro81812 жыл бұрын
No you dont remove the water canister. You will need to remove the headlight plastic bracket behind the headlight. Once you start removing you will kind of figure out.
@vloniello2 жыл бұрын
Depends on model, the 4.8 driver side was significantly worse with oil cooler in the way. Driver side took about 2 hrs replacement and passenger 1 hr for me.
@farqueue3 жыл бұрын
I dont understand why you need to cut it off? it wouldn't pop off like it pop on because of the glue? i guess solvent is hard to penetrate it for release without damage the lights
@thebudgetpro81813 жыл бұрын
Yeah the glue is a hard disolvent glue it basically melt the to materials together and wont pop off if you het it up. And if you heat it up too much you could potentially damage the soft rubber of the housing. That was my reason for cutting them thanks for watching 👍
@haikalmatnoor71733 жыл бұрын
@@thebudgetpro8181 yup, i damaged the housing rubber.
@mrfunkee83083 жыл бұрын
What kind electric saw is that?
@thebudgetpro81813 жыл бұрын
Its an oscillating tool with a wood blade.
@joeljohnson1757 Жыл бұрын
I did this. But only lasted 6mths even with uv ppf. Might have to use 3m ppf next time instead of the cheap ebay stuff 😢
@1988oleshka10 ай бұрын
what exactly happened in 6 months ?
@Djsatile2 жыл бұрын
Y’all u do not have to take the tires off if u got 18 inch rims just turn tire to take out
@juniorwilkinson8968Ай бұрын
Bro am literally charging 10k for this job😅😅seriously
@thebudgetpro8181Ай бұрын
No way bro i need that kind of job lol
@mcplutt2 жыл бұрын
Probably a lot cheaper than new headlights.
@andrewwynn9 ай бұрын
95% cheaper
@DanFer052 жыл бұрын
Rubbing compound easier
@Cup-o-Wealth3 жыл бұрын
The most difficulty is trying to get the headlight out pass the washer fluid tank on the passenger side. Too bad your camera failed to record it. You didn't say if removing the bracket under the headlight helped either.
@davetheheed3 жыл бұрын
There’s really no need for this butchery, just wet sand the lenses then polish & seal. The new lenses will fade with time too..
@thebudgetpro81813 жыл бұрын
Once lenses are broken or yellow sun burn you wont be able to leave them like new quality no matter how many times you wet sand them and polish them
@bluegables Жыл бұрын
You don't have this car. Mine is totally cracked, already done sanding, no use.