#07 Traxxas Slash 4X4 - Steering Upgrade Part 1/4

#07 Traxxas Slash 4X4 - Steering Upgrade Part 1/4 - STRC Bellcrank Install!

Рет қаралды 65,268

6 жыл бұрын

One of the all time great RC vehicles - the Traxxas Slash 4X4!! Now with On Board Audio and Traxxas Stability Management system!
In this video we replace the stock bellcrank setup for the STRC Aluminum Bellcrank, for even better steering performance!
Amazon Links!
US : amzn.to/2glSmOF
UK : amzn.to/2wLSTUd
DJI Quadcopters and Camera Gear:
kzfaq.info/sun/PLkAeX8W01U1j9Yt1B5L2FJJpCEpA-8gDr
Non-GoPro Action Camera Reviews:
kzfaq.info/sun/PLkAeX8W01U1ikJ4i35DhuqrLLzI7UYNEk
Action Camera Accessory reviews!
kzfaq.info/sun/PLkAeX8W01U1i6A7Qr4nzYhZhBoVRZvgv9
Camera Gimbal Systems:
kzfaq.info/sun/PLkAeX8W01U1iJPcIgQd16IAImg8nYpheH
Traxxas Slash Upgrade Project!
kzfaq.info/sun/PLkAeX8W01U1h46ifZg3VaM212BsYWOR5B
GoPro Reviews, Tips & Tricks!
kzfaq.info/sun/PLE5C176859DE6BC92
Smartphones/Tablets & Apple Stuff:
kzfaq.info/sun/PLE259065D8C16E1C6
Drives/Storage - NAS and DAS systems:
kzfaq.info/sun/PLCEDEB6BDBCD223BA

Пікірлер: 39

@fcsthememe7987 3 жыл бұрын

I prefer the Hot Racing belllcrank, the stock makes slop because of those shoulder screws you recycled. With the Hot Racing bellcrank it uses a truly smart and simple tie bar set up that eliminates all possibilities of tire slop.

@jacobwheatly9300 2 жыл бұрын

These vids save my life

@iftibashir 2 жыл бұрын

Glad they helped. Thanks for watching!

@mixflip 5 жыл бұрын

Wow it's nice to see you expanding your content. I found you first by watching your budget action camera videos years ago. I now have a Slash 4x4 and here I am again watching your vids!!! Keep up the good work.

@iftibashir 5 жыл бұрын

Thank you!

@palnagy3779 2 жыл бұрын

I was just rebuilding my Wltoys 124019-RC as the left front hub went out and I had to put in the full swingarm kit, along with the cornering and because of your video I was able to remove the steering bearing! Thanks!

@s1ckksn0w 4 жыл бұрын

thank you so much i just got my bellcrank for my slash 4x4 and was confused on how to assemble it left a like :)

@iftibashir 4 жыл бұрын

Glad it helped ;)

@kymmoulds 6 жыл бұрын

Even though I'm not into RC's the video is interesting and informative. Well done.

@iftibashir 6 жыл бұрын

Thank you!

@dylanwhite6539 4 жыл бұрын

This looks way better than the hot racing model. However I would like to note that the A arm removal with the stock bulkhead, while easier, is not necessary. You can still rather easily assemble the left and right cranks, put them on the bulkhead then slide in the connecting rod.

@rc4life280 6 жыл бұрын

I’m subbed great vids👍👍👍

@ramilamrahov8808 3 жыл бұрын

Great upgrade.i will buy.

@1Nolimited 6 жыл бұрын

Realy nice a waiting the next video ;-)

@supercop1977 6 жыл бұрын

Great video! Do you have a video to show how to set up an antenna the way you do?

@matthewtrotter781 6 жыл бұрын

This is my next upgrade. How do you like it. I did my servo drive shaft and HD axles 1st. This should be here by Saturday Monday at the latest.

@7.62Ak 6 жыл бұрын

If you order this, you better order a metal geared steering servo with it because you will most definitely need one sooner than you think. Trust me I upgraded mine to the aluminum strc bellcrank and the stock servo didn’t last no time.

@iftibashir 6 жыл бұрын

Yup - mentioned this in the video ;o) Next video is servo upgrade - kzfaq.info/get/bejne/a5piqMdlx9jXoWQ.html

@Dylan-zj1lz 2 жыл бұрын

Are you able to tension the servo saver with the STCR Bell crank?

@mohdalqahtani411 6 жыл бұрын

Bro I have this problem with my Traxxas UDR should I do it same or what can I do the best I found there is a vibration when I do full throttle 💔

@seb.9775 4 жыл бұрын

Are you living in the uk ? If so where did you get that servo saver I need 1

@CMoneyAdventures1992 2 жыл бұрын

i know im showing up a little late to the party here, but if I'm thinking correctly the procedure should be very similar in the 4x4 stampede. Correct? i have a stampede that has a very minor pop when steering and i believe this part is the cause of the issue. cuz im watching it wiggle inside on the shaft as it turns.

@g59spencerlaska23 4 жыл бұрын

Does this work with the original/chassis

@jasonmoretski6910 3 жыл бұрын

I think it’s hitting the front differential? I don’t know maybe you have a better idea

@jasonmoretski6910 3 жыл бұрын

I installed this on my slas 4x4 lcg and something is hitting any idea?

@colin-jc1el 6 жыл бұрын

Could I use aluminium strc Bell crank my 2 wheel drive slash

@landon6128 5 жыл бұрын

colin no they have different designs

@freesteff2010 3 жыл бұрын

I believe you can

@LandenDenham 3 жыл бұрын

I think

@freesteff2010 3 жыл бұрын

I've read in rc forums it works for 2wd

@Issac_G 6 жыл бұрын

is that bell crank hard on the stock servo? thanks fro the video

@iftibashir 6 жыл бұрын

Yes it will be a bit harder on the plastic gears in the stock servo....

@andrewkelly3702 4 жыл бұрын

My only problem with aluminum parts is the chance of them bending.

@mrnuts3317 3 жыл бұрын

Does it rub on center shaft?

@iftibashir 3 жыл бұрын

No it should be clear

@Savage1Living 11 ай бұрын

I don't get it. I watched this and your bulkhead install. I built my truck 5 years ago, went together no problem. Servo horn screw backed off. Took the front bulkhead apart to fix it and now no matter what I do I cannot get the steering linkage/servo to stop binding. Everything is in the same exact position as yours in the video, yet, I slide the bulkhead on, and tires immediately go to drivers side left, can't steer in either direction, binded. What the hell gives