Dude! Finally someone brings up the filament under the fingernail! I had a piece go all the way to the back of my nail.
@TheEdgeofTech Жыл бұрын
OUCH!!!!!
@5mmTech10 ай бұрын
Some things just can't be unread. 😨 sorry that happened to you.
@dia35 Жыл бұрын
STOP! Now I see I need to order a new printer.... dang it.... Now you've cost me another $1400. Looking forward to my Bambu carbon
@TheEdgeofTech Жыл бұрын
HAHA Something tells me you were on this path before you saw this video, but I hope you love the printer!
@olafb.2929 Жыл бұрын
My thought, just need to get it financed 😀
@mikebalentine Жыл бұрын
Have loved mine, amazing device
@jeffj5710 Жыл бұрын
Same here, just ordered mine.
@dia35 Жыл бұрын
@@jeffj5710 you'll love it so much, you may order more. I am in love with mine and amazed every time I use it at the quality and speed it performs.
@jmsether Жыл бұрын
With the cardboard spools, I rip the two sides off and then use the spools that came with the printer as they split in half. There are also spool models built into the printer. This works the best with the AMS so far. You do not need to remove the center cardboard spool as the spool model slips under that.
@WeAreSoBackBros Жыл бұрын
Thank you!
@Mirrormn Жыл бұрын
I messed around with all sorts of different rollers and rings for cardboard spools, even tried designing my own, but wasn't happy with any of them. You need rollers to be very snug on the cardboard so that they don't slip when the AMS is back-rolling them, but you also need them to be very narrow because the bottom of the AMS has channels that are only about 10mm wide, and if your rollers rub against those, you'll have retraction errors too. If your cardboard spool is dented or not perfectly rounded or centered, a roller can exacerbate that and make it wobble in the AMS, and if your roller has retaining clips that go over the edge of the cardboard to hold it in place, stuffing it under those clips can create the dents and imperfections you don't want. In the end, it's *much* easier to just wrap a single layer of electrical tape around each edge of a cardboard spool. That gives you great traction, no slippage, no extra width, doesn't need to be carefully adjusted for different brands, and it's faster than printing even the smallest roller. Which should be a lesson to us: not every problem is best solved with a 3D print.
@tkcdac Жыл бұрын
The least amount of work for simple prints, is just to ditch the AMS and use the back spool holder.
@nategoodwin33295 ай бұрын
You are a flipping hero. Thank you.
@marsgizmo Жыл бұрын
super practical upgrades! great video! 👏😎
@TheEdgeofTech Жыл бұрын
Thanks man!
@JezzyCrazyTV Жыл бұрын
XD its new that people dont go to the biggest channel comment but sadly i do btw i bought the bambu lab combo its the best
@markcraig85993 күн бұрын
I love Saul in the background 🔥🔥 Im gonna make on in marble right now lol
@pikapalooza7339 Жыл бұрын
Just got mine today! Printing the poop chute as my first real print after the benchy :)
@UncleJessy Жыл бұрын
Omg this list is amazing. Need to print them all
@TheEdgeofTech Жыл бұрын
There are already so many more since I made this video as well!
@euroriderdk Жыл бұрын
The desiccant trays are awesome, so much money saved. Well the rest of the prints I already have before I saw your video, but super big thank you for sharing.
@robertthompson3472Ай бұрын
Great value! I really appreciate your videos you make for the community 😁 Guess it’s time to order a second X1C!
@thelightspeed3d712 Жыл бұрын
I am looking forward to mine... Can't wait actually. Never seen so many positive reviews.
@TheEdgeofTech Жыл бұрын
I can't wait till you get one!
@misury Жыл бұрын
Also, with the poop chute container, maybe modify to angle the bottom to an outside corner, create a through hole, and put it out over a garbage can? Then as the waste comes through it'll empty right to the waste bin. Just a thought. 😁
@TheEdgeofTech Жыл бұрын
I always thought it would be fun to have a slide attached to the back with magnets and then go down behind the desk to a trash can! Then it would really be a poop shoot!
@mindcastpodcastАй бұрын
My X1C will arrive tomorrow - I think I got my list for the first few prints right here. Super useful as it seems, thanks for sharing this collection.
@3D-Printed-Guy Жыл бұрын
Love your vids! Please would you keep making videos about the Bambu lab x1 carbon. Like time lapses with it and instruction videos. I would love to see more slicing tutorials with the Bambu slicer. I ordered one for myself recently can’t wait to play with mine!
@TheEdgeofTech Жыл бұрын
Thank you! Absolutely, I have more videos coming!
@gabrielblock2315 Жыл бұрын
How are you liking it? Worth the $$$?
@ChimpyChamp Жыл бұрын
When it comes to the spool cover I would say it's a perfect reason to learn some CAD software, a model like that would two minutes in Fusion360 (hobby licence) + a pair of cheap callipers.
@drCox12 Жыл бұрын
Too much effort. You can just scale it in Bambu Studio.
@ChimpyChamp Жыл бұрын
@@drCox12 It's effort that's well well worth it, once you have some CAD skills you can unlock the true potential of your printer.
@drCox12 Жыл бұрын
@@ChimpyChamp I agree but you should never overcomplicate things. If there's an easy and reliable way to get the job well done, then take it. Unneccessary complexity is prone to failure which leads to frustration which leads to loss of motivation. Learn step by step: Learning how to scale things in Bambu Lab is a lesson that is also applicable in CAD. Because just scaling the model is exactly what an experienced CAD user would do.
@colinrand3300 Жыл бұрын
i use wood hardener on the edge of the cardboard spools works great
@BrannonAerospace3 ай бұрын
For the cardboard spool edges, if you rotated it 90 degrees, it ends up being a lot stronger. But, it’s not very practical, and would require a ton of supports, but it might work…
@Leynad778 Жыл бұрын
Great stuff you found, thanks👍 I did two smaller sized poop-buckets that can be found on Thingiverse ("bambu lab waste basket"). IMO one of the best mods for the Bambu Lab is a simple cotton-blanket to dampen this beast. First I bought some plywood boards and build a U-shaped enclosure for the sides and top, but the most sound emissions are coming from the back of the printer that needs to be accessible. So I just put a folded blanket on top of the AMS which is just hanging loose over the backside, but huge improvement. Not much improvement in decibel, but it filters this annoying high frequency hall-effect sounds very well and just sounds like common printer with it, not like a factory. IMO Bambu Lab should offer a silencer out of foam for it that fits nicely on the back.
@VigiHunter Жыл бұрын
Any Problems with heat or airflow?
@Leynad778 Жыл бұрын
@@VigiHunter Nope, the defaults work with all filaments I'm using and don't tinker with temperatures, flowrates etc., but just quality settings like shell- and infill-rates. I've one very cheap TPU-filament that wasn't working well and the default speed-settings with TPU should be reduced anyway.
@VigiHunter Жыл бұрын
@@Leynad778 Oh I don't means heat while printing but heat problems in the back where the PSU, Mainboard and stuff is. There is quite a large fan back there so I was wondering if a blanket makes it a heat trap 😅
@Leynad778 Жыл бұрын
@@VigiHunter Certainly not during a German Winter.
@FireDragon3D Жыл бұрын
These are great upgrades for the Bambulab printers. The spool ring i use is from Blizzard called the Cardboard Spool Ring for Bambu Lab AMS (parametric) - I resized it for Polymaker cardboard spools by 1.5%
@chrisgulotta Жыл бұрын
Great info Jim, I was in need of a poop bucket for my poop chute.
@TheEdgeofTech Жыл бұрын
😂😂
@eliasney5 ай бұрын
Dude.. When you pulled out #5 with the feet to the build plate holder I actually died.
@TheEdgeofTech5 ай бұрын
😂😆 Glad you were revived to write this comment!
@tommer500810 ай бұрын
Please! The video transitions. OMG, I am almost tossed my device. It's bad, Jim. Don't use that one anymore. I am begging you. Your videos are so good, too!
@556bc Жыл бұрын
That transition noise is atrocious.
@unrealbasic1612 Жыл бұрын
Thanks, I can't recommend that splitter however seems like that would be prone to jamming.
@mike617043 ай бұрын
I just use rubber bands around the cardboard spools. Been pretty great for me.
@grahamwood31055 ай бұрын
thanks very much for all of your help with all this downloads.good work
@NipkowDisk Жыл бұрын
An excellent collection of useful items for my X1 Carbon which should be arriving next week! Subscribed.
@gumush Жыл бұрын
Did you try to feed TPU to AMS hub for printing multiple materials with TPU ? by that way maybe we can use external spool holder -> AMS hub
@rexdengaming522 Жыл бұрын
got my x1-c ordered it should be here in i say about a month or so. thanks for the info, this will really help me starting out!
@AndrewAHayes Жыл бұрын
X1 Carbon Morpheus? Oh by the way, maybe painting the edge of the cardboard spools with nail varnish might make them strong enough to stand upto the AMS.
@lukeqi9265 Жыл бұрын
The revised “magnetic” poop shoot version is absolutely excellent.
@AlanTuringWannabe8 ай бұрын
For the last one with the center tearing out I suggest you design you own or use mesh mixer to fill in the center for stability
@fixumdude Жыл бұрын
Great video. I definitely need to print most of these. Especially the nozzle holder for my stretch goal nozzles.
@TheEdgeofTech Жыл бұрын
You should! I think it looks sweet to have them displayed too. lol
@Cereal_Killr3 ай бұрын
Just throwing this out there. I been running cardboard spools in my AMS for months with zero issues. I had a few rings that I actually tossed in garbage because I was'nt using them. Cool video with alot of cool stuff! I need to make the plate stand for sure!
@turboboostHoonicow5 ай бұрын
Nuce upgrades! After the waste box, a ams riser was my 2nd upgrade I did!
@mporei11 ай бұрын
great job man !!! you are very nice !!! keep going community !!!👍👍
@Taliaris4 ай бұрын
Very helpful! Thank you!!
@theianmce Жыл бұрын
Really appreciate the summary, thanks!
@anupreetkaur4331 Жыл бұрын
This makes using the printer so much better
@omololadopamu4754 Жыл бұрын
I'm glad I came across this 3D printer, hoping to get one soon
@olafb.2929 Жыл бұрын
Hi Jim, Thanks for the video. It makes me want to have one even more. Please show us more of it and its prints. And, if a human poop chute clogs, it is not good too 😉
@TheEdgeofTech Жыл бұрын
Haha
@reed1sam9 ай бұрын
Great video, thanks for compiling and sharing the tips
@JeremieDeWitt Жыл бұрын
What type of filament should this be printed in? I'm waiting for mine to come and I want to get some of it done ahead of time.
@Av8orDave9 ай бұрын
I've given up on wheels for cardboard and gone back to printing my own full spools. I use Inland filament from microcenter, and even an extra 1/16" is enough to drag on the cover for the AMS. I may try and make my own wheels that don't wrap around the edges of the spool, but just barely extend past the edge.
@robrimell9684 Жыл бұрын
Great video! When I imported the poop bucket stl into my Bambu slicer, I got a message "error - a gcode path goes beyond plate boundaries". Can I safely ignore?
@RumourHasitYT Жыл бұрын
Same here, if you find a solution let me know thanks
@pufferfish12321 Жыл бұрын
Great vid, thanks heaps. Are there recommended filaments for these upgrades? I only have PLA, wondering if I need a stronger filament to order with the X1C
@AnomieDomine9 ай бұрын
Anything that gets hot should be at least PETG
@GunnerAl9Ай бұрын
Need the new spool holder the AMS to move it from the back of the machine to the side of the machine so you can push the entire case against the wall and not have it out 6 to 8 inches. Great idea. Bamboo should have thought of it.
@3vlogs4876 ай бұрын
Trick with the desiccant trays. If you have stockpiled filament I never throw the desiccants that come with those away, and I just keep recharging that.
@utdallaz7 ай бұрын
Thank you!
@gwchomperz64718 ай бұрын
Just got mine! This thing is beautiful
@justincider88928 ай бұрын
I don't know if polymaker changed their spool size since the models were designed, but the standard polymaker spools I have fit/work fine in my AMS without the additional adapters.
@timj12629 ай бұрын
Thanks great video
@Indy69vette9 ай бұрын
Cool, didn't know Weird AL has a KZfaq printing channel
@ottokueng42362 ай бұрын
Good informations. But the Y-Splitter does not work. After feeding the filament, it takes some seconds and the filament spools back. After some trials for and back it stops. Sometime it works the first time, sometime after 2,3,4 trials. After disassembling the Splitter filament loadings works without troubles. It seems the time is now to long or the force to low.
@KaiusFilius3 ай бұрын
Regarding the cardboard spools: I found in another video, that you can use the bambu reusable spools on that cardboard spool really well, if you remove the sides. But I haven't tested it yet, because my bambu filament isn't gone.
@vetulamortem6 ай бұрын
Coulnt you just scale the spool thingy up a bit so it fits? or use a Master Spool and just trasnfer the Material from Cardboard to Masterspool
@MATS_MAKERSPACE Жыл бұрын
Hey Jim great video, only ordered mine on Friday but I'm stoked to be on the list. I love the build surface holder but I think someone needs to do a remix and stagger the slots from left to right so you can grab any of them from the side.
@TheEdgeofTech Жыл бұрын
Believe you could just rotate the build plates and be able to grab one from each side if you wanted to! Can't wait till you get yours, you're going to love it!
@MATS_MAKERSPACE Жыл бұрын
@@TheEdgeofTech I've sold evething but the mini to fund it but I'm 100% sure it's money well spent
@BobbyHill2973 Жыл бұрын
Great stuff!
@MacmanPilot6 ай бұрын
Duramic cardboard spool printed rings work on the poly as well
@snugglebuns69694 ай бұрын
Can u use the printed splitter to load and use TPU? asking for a friend.. TIA
@eyezeeeyeprints9452 Жыл бұрын
Currently, I’m using a drill mounted spool winder that uses a 1/4 Allen key to attach to the drill and had strength to the part. I mount the bambulab spool on my drill and just rewind my filament from polymaker onto the bambulab spools.
@gieslebt10 ай бұрын
What kind of reliability or customer service are you guys having with the Bambu machines?
@TheEdgeofTech10 ай бұрын
Good question! It's been good for me! But they are still growing and they are not perfect. It's much better than most other companies though!
@JurassicJenkins Жыл бұрын
I see what you did there - @1:17 🤣🤣💩 oops - Great vids!
@crowguy506 Жыл бұрын
Actually the single piece version of the front lip prints fine in the X1. No need to split it.
@boonjabby Жыл бұрын
Yes. Filament under the nail is death !
@NerdyCraftsmith Жыл бұрын
Can't wait to get my Bambu X1 Carbon
@STxFisherman Жыл бұрын
Great video. Thanks!
@TheEdgeofTech Жыл бұрын
Glad you liked it! Thanks for watching!
@kevinschilling6813 Жыл бұрын
We need the STEP files to add some thickness to the center hole in the cardboard adapters. That would make the area thicker and less prone to fracture. -OR- you have to do the hoop jumping and go through FreeCAD to convert the STL to a solid model then save it as a STEP file. Then.... Make the corrections/alterations.
@blatherskyt6 ай бұрын
Gotta give him props for making the “poop shoot” #2 on his list. 💩
@RobR386 Жыл бұрын
I re-spool filament from cardboard spools onto used plastic spools
@jraiello Жыл бұрын
Just ordered P1P, but in mean time, decided to download Bambu Slicer and practice on my Ender 3 V2 (the only Creality printer option in version 1.4.1). And to my pleasure, it is fantastic and the quality of print is better than what I was getting with Prusa Slicer OOB and faster. Two Questions: 1) How can I setup my Ender 5 Plus as a new printer in the slicer? 2. Is there a way to directly send the gcode to the Sonic Pad Moonraker/Fluidd interface? Both printers have SonicPads...
@NinjaKiller1022 Жыл бұрын
I’m so glad I’ve come across this 3D printer, and can’t wait to get my hands on it. Also, can you use 3rd party filaments with this printer? It’s not a deal breaker if you can’t.
@ethurial Жыл бұрын
I have this printer and use third party filaments no issues so far. Used pla, pla+, pla-cf, silk pla, and asa.
@cratervanawesome Жыл бұрын
Why not just resize the small edge covers to fit before printing? It should be pretty easy math to remove or add how ever many mm of diameter you need.
@tremaynebaird6839 Жыл бұрын
Ordered this printer already haven't got it yet but currently use almost exclusively polyterra since I have a local distributor for it, is there a problem with using it in the AMS?
@TheEdgeofTech Жыл бұрын
I have not had too many issues with the AMS at all. Hope you love it when you get it!
@canadianoperator3 ай бұрын
You don’t have to unplug your AMS when using the Y splitter. Just uncheck “Enable AMS” in the slicer and make sure your external spool is selected.
@abcdefg-tj8ij2 ай бұрын
Yea you're right, Believe it or not when the video was made that option wasn't a thing yet and you did have to unplug the ams
@ZhakRyuu5 ай бұрын
You know you can upscale the spool rings to fit your spools right? I mean its a matter of measuring and inputting the correct diameter in the slicer...
@JCthe1maximus6 ай бұрын
Can you share where you got the Dual-Sided Textured PEl Plate from, the only PEI plate Bambu has is the Gold one, Temu has one similar to the one you have, and amazon has a few without the markings.
@Titan3DAZ Жыл бұрын
I see what you did there with the #2
@TheEdgeofTech Жыл бұрын
Haha 😂
@fivelights907 Жыл бұрын
This is awesome. Thanks. I guess I’m gonna be printing that bucket PDQ because I bought this for the AMS. Still waiting for it but I’m ok with that.
@Frostyblaq Жыл бұрын
Wow I never knew this will happen
@hv1461 Жыл бұрын
For the Y splitter, what do you mean 'ams is unbplugged'. I mean, can you go through the steps to make a print from filament in the AMS, to make a print from filament on the back. Thank you.
@bitman056 ай бұрын
Tried electrical tape on the edge of an Overture cardboard spool this weekend. 13 hour + print later, all is well.
@scotthancock8225 Жыл бұрын
You can recharge packets of desiccant as well
@TheEdgeofTech Жыл бұрын
True! But I like the idea have it holding more too. Thanks for watching!
@lesliesavage92297 ай бұрын
I was hoping to see something good. For your Polymaker problem you can design your own in CAD, and print them in PETG, which stands up better than PLA. Design your own. I did with my ECO spools, which were smaller than the Overture rings I had.
@ktothestank Жыл бұрын
Holy crap I'm so honored you showed my design on your page!! Thanks so much
@TheEdgeofTech Жыл бұрын
Awesome! Which one was yours?
@ktothestank Жыл бұрын
@ktothestank! I'll take your comments and buff them up a bit mine are abs/asa and still working!
@LeeroyJenkins9421 күн бұрын
why dont just use clear or electrician tape over the edge of the cardboard spool ?
@popeizzy20125 ай бұрын
Scale up the ring in the slicer to fit
@carstenmller1105 Жыл бұрын
You said that you would put a link in the comments to the files for the print. Can't seem to find them 🙂
@TheEdgeofTech Жыл бұрын
Take a look at the description of the video, and you'll find all of them!
@HobbyPrinting-ew5rr11 ай бұрын
thanks
@dysin_9689 Жыл бұрын
i would say the filament under the finger nail is like giving yourself bamboo shoot torture by accident.
@ArcNestIndustries Жыл бұрын
where are the links to the files to print these objects?
@ArcNestIndustries Жыл бұрын
Found them!
@Woodpecked1 Жыл бұрын
I got the P1P 2 Days ago - Woot!!!
@CelicaRyder69 Жыл бұрын
Polymaker has a file on printables for their spools now
@davidhirsch2980 Жыл бұрын
lol why isnt the build plate holder and the feet combined into one piece?
@thenextlayer Жыл бұрын
Super high quality video, great work! I'm jealous of your studio - and your X1
@LJ-gu2dj Жыл бұрын
Hey JIM! Long time no see ;)
@TheEdgeofTech Жыл бұрын
Hey! From your KZfaq name I can't tell who this is, but hi!, It's been a long time! Haha
@menchen222 ай бұрын
why you dont scale the spool holders?
@Troybv Жыл бұрын
Hello, do you think placing the X1C on a antivibration mat like for washing machines could get the noise levels down a bit? Mine is on the second floor and I can hear it trashing about in my downstairs living room.
@TheEdgeofTech Жыл бұрын
Maybe! It certainly would help from transferring the vibrations to whatever kind of table or countertop you have it on. And that would probably cut down the noise to the rest of the house.
@Adam08559 ай бұрын
Please advise me if it is worth paying extra for x1 or is it better to take p1s?
@Zplizor Жыл бұрын
You can always dehydrate the dececant !
@NMHC19785 ай бұрын
how and with which settings did you print the y-splitter. everytime i print one the filamnt is not going thru fully it is always stuck when it tries to go thru the ptfe tube on the out side of the splitter