#10 How to Slip a PTO Slip Clutch
Рет қаралды 34,687
Күн бұрынIn this video I go over how to slip the slip clutch on a PTO shaft. This needs to be done periodically especially if it sits outs in the elements. If the slip clutch seizes up, you will not have any protection for you PTO system and could cause serious damage to you tractor. I also cover some basic maintenance tips. Hope you enjoy! Thank you and have a blessed day.
@jamesgrigsby8986 2 жыл бұрын
I see that light shining, Brother...
@RockhillfarmYT 2 жыл бұрын
Nice job
@TheCajunHomestead 4 жыл бұрын
I seen your name on Hamiltonville, I have a few tractors I am rebuilding/restoring. I hope to watch all your videos, this one is well done.
@BBLandServices 4 жыл бұрын
The Cajun Homesteader thats awesome. I appreciate it. I try to produce good videos on a budget. Recording all on my phone now. Eventually will upgrade. This quarantine has me with a lot of down time so figured I might as well make some v roll! I subscribed. I want to eventually get an old tractor and restore it.
@ramchillarege1658 Жыл бұрын
That was a great video. Thank you.
@BBLandServices Жыл бұрын
Thank you!
@MinnesotaPikeVideos 3 жыл бұрын
Good info thanks.
@PawPaws_Place 4 жыл бұрын
Great video. 👍
@BBLandServices 4 жыл бұрын
Thanks.
@manwar999 3 жыл бұрын
very good video
@BBLandServices 3 жыл бұрын
manwar999 thank you
@RockhillfarmYT 3 жыл бұрын
Nice maintenance video. What model of tractor do you pull that with?
@BBLandServices 3 жыл бұрын
Rockhill farm and homes was pulling it with a 3025e but then upgraded to a 2038r
@RockhillfarmYT 3 жыл бұрын
That is what I have. Great tractor
@BBLandServices 3 жыл бұрын
Rockhill farm and homes oh yeah. It’s daylight and dark compared to my 3025e.
@Rip1Outdoors 2 жыл бұрын
watched it all. I have the same cutter. Question. It is pretty new so it should pretty much be right? Good video rip1outdoors
@BBLandServices 2 жыл бұрын
Depends on how long it sat on the lot and if the dealer did a PDI that included slipping this clutch. I have gotten some that were locked up when I got them.
@stevensteele2002 2 жыл бұрын
Sorry about an amateur question but I have to refer to my manuals for everything and it seems like the manual talks about using grade 2 bolt for the shear pin. In your video you use specifications for a grade 8 bolt. Should I be using a grade 8 bolt for a shear pin or using grade 8 specifications on a grade 2 bolt?
@BBLandServices 2 жыл бұрын
You use a grade 2 shear bolt if you do not have a slip clutch. The slip clutch takes excess loads and does not break so you do not have to stop to change a broken bolt. So you use a grade 8 with the slip clutch.
@earlwagner5940 2 жыл бұрын
Is it possible to grease the universal through the slip clutch cover and is there a trick to putting it back on if you take it off? The cover, not the universal.
@BBLandServices 2 жыл бұрын
On the frontier I couldn’t without taking it off. My new MX5 cutter has a cut out that lines up and you can grease it in place. The more frequent you take it off the easier it is. Grease the shaft when you have it apart.
@earlwagner5940 2 жыл бұрын
@@BBLandServices I took a 1 1/4" hole saw and made an opening directly over the grease fitting. Now I can grease the universal joint without removing the slip clutch cover.
@BBLandServices 2 жыл бұрын
Nice good thinking
@louisianapepper1018 2 жыл бұрын
I got a 3032e and my bolt broke and it's to far back it won't come forward.. I'm like wtf I can't put a bolt in if it won't come forward. Do Im very confused
@BBLandServices 2 жыл бұрын
Which bolt?
@louisianapepper1018 2 жыл бұрын
The bolt for the bush hog. Shear bolt or the grade A bolt. I should of loosen up my clutch. But now the shaft went to close to the gear box and it won't come forward. I'm not understanding since in the video you just slide it on really easy
@BBLandServices 2 жыл бұрын
@@louisianapepper1018 probably cause some burs when it broke and that’s what’s holding it on. Probably going to have to persuade it a little.
@OnSiteTrav 2 жыл бұрын
Use a punch and a hammer
@jacksmith9937 3 жыл бұрын
How important is the slip clutch cover? I hate messing with that thing and am tempted to leave it off.
@BBLandServices 3 жыл бұрын
Yes it is a real pain on the a$$. I’m glad my new MX5 has a metal on the flips up. It’s a safety think you could take off if you want the risk.
@chriskaravias6431 2 жыл бұрын
Question, What's with the pistol. Hunting or self defense.
@OnSiteTrav 2 жыл бұрын
American fashion
@BBLandServices 2 жыл бұрын
I was raised by marines turned federal agents. It’s habit to always have one with me.
@Rip1Outdoors 2 жыл бұрын
@@BBLandServices me too!
Gufee.medalin
Рет қаралды 8 МЛН
Echo Routine
Рет қаралды 15 МЛН
Елена Фроленко
Рет қаралды 3,7 МЛН