Thank you , it was good and clear!!

Thanks for this video, I was suspecting about that conector is sufficient to add a battery, and you confirmed me that. It seems to be easy, I'll try watching your video. Thanks!

Bravo bravo bravo

1 adet pil yeterli omadı amper düşük geldi Ben 2 adet 18650 paralel bağladım harika oldu . Teşekkür ederim

Exactly what i wanted to do , thanks, much more fun DIY your own batt , rather buying thats already install, plus hou know thw battery your gonna put is better.

I have that microscope and it came with the battery. I do not like the USB port connection on the side for charging. It is really close to the case and does not have enough room for most cables to fit. I am going to attach a battery holder to back and use two 18650 cells in parallel and run a wire inside to the board. That way I can remove the batteries when they need charging instead of having to use a USB cord. I will also be attaching the microscope to a microphone boom. The base is too small and gets in the way. A separate lamp from the side is also useful for better lighting as the LEDs on the scope give off too much glare.

Gebruik een stukje krimpkous om te isoleren, en koop een rolletje goede 60/40 tin. Verder goed bezig 👍

For the future, connect the LCD first, then the battery. ;)

I wonder if the machine is still working well? Can it be charged using a normal micro usb port? (green light indicator when fully charged?) Thank you

2 adet 18650 pili paralel mi bağladın

Hi Tim , got few questions 1. How long do you get battery backup? 2. Is their any problem you have face after the modification?

Good one - thank you. ...Have you removed the protective covering on the screen yet? It would drive me crazy having the green tab just sitting there under the bezel!

I’m curious about the voltage / power the on-board charger uses. I imagine it should be safe if you use a low power USB-adapter but it could still over-charge.

When it's not turned on but it's plugged in and charging does the led light turn on?

I did this, but mine keeps turning off what can be, did I use a very thin wire or is the battery low?

Batery 12v 5a?

I even managed to do the same as your video. However, I went back to your video and noticed that the lighting LED's are not lighting up, the same thing happened to me

Can you please tell me the battery specifications which is used in it....

Use flux when you do soldering works.

hello I watch your video and I wanted to ask you if it is possible to make a backup of the chip? my device is not usable on pc I have artifacts and sometimes it does not start it bootloop. thank you

Hello, can You hello me? I need firmware foto mustool g1200 microscope . Only red led, boy turn on with button. Thank You foto your help

Cam you please tell me the specifications of the battery

كيف يمكنني تسجيل الشاشة في هذا الجهاز

Terrible execution, and the mess ...

Аккумулятор Li-Pol (батарея) 9.5*47*60мм 2pin 3.7V/3000mAh

i bought it g1200 , and used it for a month , and i regret it , the image quality is very bad , it never gives good balance between light and dark areas , the light is refleced directly to the camera when working with cicuit boards or electronics repairs , cannot see the parts clearly and the colors is not clear too , cannot tell if there is some thing dicolored or burned , and after a month or so of usage , it died , it doesnt turn on , i opened it and tested the board , i found the circuit board to be shorting on the power area next to the charger port , and its poor design seems to have failed in short time because it generates lots of heat while it doesnt have and proper cooling , its one of the worst microscopes in the market and no matter what price you pay for it , doesnt worth it never buy this model , you will end up throwing it in trash

Very bad , not easy change battery replace. Other products buy.