This thing is getting out of hand! And i'm absolutely loving it. Front mounted intercooler next!

Very old school Mighty Car Mods feeling narration, I like it!

You’re going to need an intake plenum(between the turbo out and throttle body)with about two liters or so of volume to build boost. Small displacement, single cylinder engines just can’t do it without intake volume.

These drift cart video series are a absolute banger :)

Hay that oil plate is for a oil cooler it's ment to loop as I believe it feeds the oil to the head

Love your build so much so I am litterly building it myself!!! Got a 125 with a three speed in a Tao Tao cart I am turning into a trail cart. Calling it a mini SxS. The fuel injection just arrived Friday. Saving to get the turbo setup next. Thank you so much for the inspiration!

Adding Voiceover adds so much to the quality of your videos. Definitely a great call there

Wow mate! I could watch this build forever 😊 Good job 🤠👍

try running a ground wire from the battery to the block, the ignition system from factory will be a self contained system that runs of its own power and ground supply so adding in the ecu on an external power and ground could cause the trigger system not to function properly with the ecu. trigger wires are sensitive to background electrical noise and always require a good ground. your sensors will all run off a 5v reference voltage. make sure your 5v and 12v systems stay separated or youll cause yourself dramas like TPS being stuck on 0% or 100% also your air intake and MAP sensors could do wacky things. if your triggering with a hall effect sensor the rising and falling edge of the trigger could not be stable so find the more stable trigger edge and set it up in the ecu. should be a setting for rising and falling if the software is half decent. im assuming it would be a reluctor style trigger so you can always check the gap of the magnetic pickup also make sure it free from any iron filings. if you can get away wit it id also try running two head gaskets and maybe even port out the head to lower compression so you can run more boost! itll be hard to hear knock on such a tiny engine so better safe than sorry. or just go an octane booster additive good luck , i cant wait to see this thing rip!!!

My son and I love watching your channel, this project is our favorite!

That engine is surprisingly complex for how absolutly tiny it is, essentially a small scale "modern" car engine at this point with all the ECU stuff and fuel injection, really interesting to see! also sick welding, you always say you are a rookie but man watch your old videos and you can see a difference in your skill, can't wait for the stu tu tu tu noises from that comically undersized beast

You're awesome bud. You set yourself to something and go nuts till it's complete! Lol. Like each series you do you just go ham uploading every other day. But when you're chillin you post weekly. I love it cause I always have something to watch

So nice seeing the pipecuts up close finally and still, very good job, as you said in the vid aswell that lots of patience is required and you nailed that sir! ❤

I'm glad you got that block for the side of the head. that exhaust is pushing Overkill... Looking forward to hearing that Stainless straight pipe "Ting"

The pie cut stainless exhaust looks epic. Tigging stainless steel releases a ton of toxic fumes that you don’t get with low carbon steel though and you should probably wear a respirator

My favourite youtube series by far

Your nuts bro love wat your doing been watching Since 12 day of mikemus and I just can't get enough bro love al the way from the from pommy land

I'd love to watch another series with a bigger engine😁

Dude this thing is epic!

Grind hard plumbing and boosted boiis have Lil 4 stroke turbo karts and they run a intake setup you might benefit from ✌️

Nice work. You will need some kind of intake manifold for the turbo to work proper,I saw that from the boosted boys go cart. It’s sort of a boost or air accumulator it helps a lot with turbo one cylinders. Good luck with the build!🤙🏻

this things bloddy mint

Shot for the long video Mike! The excitement is building. Depending on how you're gonna mount the intercooler, I'm almost seeing some Yamaha Banshee vibes 💪👌

Should drop some mini wheelie bars on the back to add to the insane look and styling ❤

The aftermarket ecu might need to see home or tdc to give an accurate spark. Like a notch or a missing tooth in the pickup for crank sensor.

Just saw the boosted boys and their turbo shopping cart, they made a sort of intake manifold for the thing. Grind hard plumbing co showed it in their recent video. They said that helped make positive boost. Figured I’d offer the info! Build is looking killer!

you’re a legend mike, should definitely mudguard/steel tub the wheels to protect anything harmful materials flicking up and taking out an eye or destroying the engine😂 (glass, rusty metal, rocks etc)

I love this series, great job man

The pie cut method is aka lobster tail, or lobster back, (for obvious reasons!). It looks awesome!

Looks SICK bro! cant wait to hear it and see it moving. keep it up dude!!

Can always heat wrap the exhaust. Couple different colours now too. Can look pretty good.

Love the vids, Mike! They are so satisfying to watch. Love your presenting style and energy. I feel like we have known each other for years, even though I am in Europe and have watched about 10 of your vids.

Omg ive been watching this since the first video, and with every video it just makes me wanna do it to my lil 79cc PhatMoto Bike XD I love your videos man, keep up the great work!!

You are amazing! Great job!

Your work is awesome bro keep it up 🇹🇹

Holy hell just found this build. This is awsome!

I absolutely adore that exhaust ❤

I'm loving this, shaping up fast!

Love your content, can't wait to see the drift kart when it's done, maybe even at Calder???

Adjust the magnet if you want change to injection,

Soo keen to see this build up and running

Sounds like the ecu is set on 2 cylinders. Sounds like it’s popping every other turn. May check that!!

Damn this things gonna be fast 🤘

Just a suggestion i run 12 inch go kart rims on rear to fix back from being narrower than front

This is amazing I really want to do this to my bike 😊 you have done an amazing job👍

I have some advice. those single speed engines with just drive neutral reverse have somewhat weak clutches that can overheat and blow up the whole engine easily. if your clutch/engine does blow out, then get a 4 speed manual 125 for a dirt bike, and that clutch is much stronger and shouldn't overheat the engine. Good Luck!

mike you needed to have some green neon lighting over the gokart and scream 'Its alive" lol

Bro can I please have that thing 😍, it looks really clean just wiring needs a little fix, keep up the work builds bro

Hell yeah man I’ve been waiting for part 2

this exhaust is like a massive snake !

Bloody awesome❤

Yeah the Turbo mini drift quad

looking dope!

Use some heat wrap for the exhaust so you don't burn your legs etc

Its going to be 1 sick kart mate

Mike lake professional fabricator 😂. Your fab skills have jumped up 10 fold since the old gassless mig booger days 😆

0:48 is oil supply and return so you dont need return line to oil filler cap

you should put the rubber tyres on the front and the plastic tyres on the back so it drifts better

You should try to use a garrett GT06 turbo instead,more boost and spool you should have

Attach a fog machine to the back to make it look rocket powered 😂

I like the pipe you made but it needs a plenum to help create pressure due to it being one cylinder

W mike

Once you get it running you should add 2 step!!!!!!!

Can we get a better overview of the wiring from the the crank sensor wire to the efi

I love the build me and my friend was going to build a go kart but can’t

Bro you should mount the throttle on the engine not with the pipe so the injector can spray the fuel straight in the chamber I think it will run smoother

Man you better fang that thing 😌

This thing is so cool bro 🤙🔥

thats fricken awesome 😂 🔥 🔥

Don't get tempted to run it in boost without that timing stuff working, even if you have to do a custom trigger or something. I wanna see this thing run and not immediately explode.

Hi Mike love your channel Bro keep up the good work👍👍

Have a question if have a min did u make it pass though carb fuel delivery set up try doing something like that before

with the learning curve being for a "fun" project, Imagine what the acquired skill set would allow you to do when one/some/all of the Cars need upgrades...

Where did you get that harness, ECU, throttle body, and injector mate? Also, what size piping did you use from the exhaust outlet on the head to the turbo?

Was that a red mk7 fiesta I see 😍

this thing is dope! beware the trans on these motors are super weak

Love the vids

hello your project is very cool . I want to know where did you buy the plate for the oil system plz ?

What is that fuel pump type called? Im trying to 3d print one but i dont know which pump type is good for that.

Did the kit come.with a trigger wheel or did you buy one separately that could be the prob could be reading wrong

Idea needed to place a turbo on a 600 RR

I think it needs oil cooler

Add drift tires is called this put plastic tubes on the tires

finally 🙏

Put a bigger karburator on it and a lighter stator 😊

What frame can I use to build this build??

Part 4 is HERE! kzfaq.info/get/bejne/pr18gJaixMDHfHU.html

Does the ecu have a wide band sensor? Love the detail on this kart.

I don't know shot about turbo, throttle bodies, ECUs. But I have the most important advice you'll ever get. Hold it flat, don't lift off, & most importantly, have fun! Hahahahahahahahahaha One day in the truck, an hour & a quarter from home, the exhaust pipe cracked at the v band. Lost all boost, towing 65 ton. Used a spare intercooler clamp & a piece of fencing wire, strategically cut from a farmers fence to hold that exhaust pipe & regain boost. It got me home, just as the pipe was starting to come loose again. The mechanic at our yard rewelded it back on, on the Monday morning. Giggles. Using exhaust pipe wrap to reduce the exhaust heat

Oh man love ya work so good

meanwhile its spooling a dry turbo lol

If you know where physical top dead center is on the ignition timing gear, then I don't see how it takes so long for the timing in the ecu to be setup correctly. I haven't seen what timing gear type you use, but in theory if your missing tooth is at 20 degrees before top dead center and you need to advance your timing to 30 degrees before top dead center... You only need 10 degrees of timing advance in the ecu... Generally if the engine does not run at all but it does pop from time to time while spinning quite easily (like yours did)... Your timing is set too late, at that point just advance timing by 10 degrees untill it runs, then make smaller changes untill it runs perfect. If your engine does not spin easily but spins in steps while your battery and starter are in good condition... The. Your timing is set to early and you should do the reverse.

Should make twin turbo so it looks like eyes

little 15 gallon jug r something

When’s new skyline vid next?

I'm not an engineer, but isn't the exhaust diameter too large? Do you think this engine can properly fill up this exhaust?

Please install performance oil pump in the engene

I built my son's Thumpstar 110cc pit bike into a full size 140cc dirtbike and I don't think he could handle it if I turbo it...😂😂😂

hey where did you get the kit

Hi mike, i was wondering if you could maybe give me a price of all the parts, like the fuel injector, turbo, EFI, because i have a Big Boy Rfz 125s and i wanted te do the same to it