This is awesome. Absolutely love it just bought my granddaughter one. I have a million Milwaukee batteries six pack Chargers everywhere absolutely love the lights

I just dropped in a 12.8 volt, 10 amp hour lithium battery into my grandkids quad. Lasts about 1 1/2 times as long as a stock battery.

I see this video is 2 years old now, did similar setup for the same wheeler as far as the 20v drill battery! However, the chuck on my craftsman drill crapped out on me. So I opened up the drill, took the wiring out, cut a good 2-3 inches up on the wires, and cut the bottom part of the drill itself off and put that part back together with the connectors in it so the battery slides right in! Just thought I’d share incase you end up doing this again and have junk drills laying around!

Cool video. Just got a hand-me-down. Only have the right side tire spin

My son has the same atv and I didn't 20v conversion with a dewalt battery. We have had problems with the gear box motors frying

Been running my son's on Ryobi 18v with great success. Been thinking about doing some lights on it too before winter gets here and it gets dark at 6pm. What LEDs did you use? Does anyone know what size motors are on the wheels? I'm thinking about slapping some 775 motors on it but not sure if it'll be beneficial

24V is fine...it has stock 570 motors 11 t pinon ( 24v capiable) and built in Heat sink to the gearbox. I have 3-ea...got it for cheap ( $0-$40) on FB market....I have the susuki and yamaha. the front wheels are the same as the back wheels. I jwack the bottom of the battery tray...so I can fit 2-ea 12v @ 12ah ( 12000mah) lead acid..that I took out of mx500...ect....12V @ 9.5 ah or 10 ah....will fit into the stock tray ( razor/schwin 24v scooter)...it runs for hours STOCK....it's 10-12 mph..fun speed for the 4-7 old old...The 10 yr/old can ride on it even..she's still under 100lb.... You WANT this BRAND to do cheap voltage increase...without striping the gears. I made it even FASTER....I took the motors from a pegporago they have 570 motors with 13T pinons...( got the perrego for $15) You need to install 40-50 amp fuse...if you make it workable/effective..without blowing the 30 amp fuse. There's stock fuse in mine. i drill cooling vents to the top and bottom of motor area. mount 12v mini/micro fan to keep the motors cool. whatever..the 570 motors are only $12 -ea......Not $100 from mltoys. You dont need a 24 volt charger...i made Y harness to the 12V power wheels charger or regular automobile charger....i have 24v razor chargers....either way I have wahzooo of stock power wheels 6 v and 12V batteries. whatever. I run power wheels on 18V i used to run 5s LIPO at 50C higher discharge. ( it has more power than the lion.) Invested $ 300 just for the batteries for the kids ( but I can use them on R/C toys too) 5000mah pack ( 10-15 mins run time)...it was sort of pain to maintain battery charging for all the grand kids ( sometimes I'll have 5 cars running at the sametime) the nieghbors kids can play/drive with them too...

How have the gears held up over the years now? Are the stock motors still going strong? I have twin boys getting these for there birthday in a few months, I’ve already done the lights and figuring what voltage I want to go with now

can you add bigger morders I would like a totorial thanks

Hi have one that needs a battery and want to just convert it so basically if I didn't want lights I could just splice into the main wire harness and use ring connectors to go into the pos and neg. Of the drill battery with a fuse and fuss holder for the pos side and it will run?

So I am currently looking to do this to my kids raptor. Does it matter what battery and converter kit you go with? And I see some batteries have a higher AH, that just means longer run time?

Nice do you know where I can get the bigger motor and stronger gears

Hey man, I just picked up the same quad yesterday from offerup for $20. Only the reverse is working. The two forward speeds don't move but it lights up when I press down on the pedal, so I don't think I need a new pedal. Do you think it could be the motor or gear box?

Could you provide a detailed diagram depicting which wires to splice and which wires to run to 20v battery, thanks

Can u just cut off the plug part that comes out the atv and splice the ends to o connecters and just put that in the drill battery?(I have a 24 volt dewalt). I also brought a charger from harbor and freight that came with o connector adapter. I was gonna cut those ends off and put them on the part where the plug use to be

i know im late to comment but there are some cool easy to install rc car led lights that i used

Could you reply back with everything I need to buy to covert my sons?? He has the same Raptor

Hello friend, I have a question. I have a motorcycle just like the one you have, I bought it a new battery and it doesn't want to work.

Which led bulbs did u order?

Can u do mine

Great but too much of a pain in the ass unfortunately

Why didn't you wire them to a toggle control ?