Referred customer interested in second opinion to repair 14yr old Ruud 5 ton system that iced up #airconditioner #hvac #airconditioning #hvacrepair
Пікірлер: 73
@welrod9421 күн бұрын
I didnt watch the video just because I dont find it interesting when you have worked on and replaced god only knows how many units but I did wanna say unless they are stupid rich they are always gonna wanna repair over replacing the unit. I mean I'm the type of guy if my compressor blows up I wanna buy a new compressor than a entire unit😂 **even tho I didnt watch the comment will still help with the algorithm
@subcoolHVAC21 күн бұрын
Thanks for not watching but commenting 😎
@ccthepope24 күн бұрын
You are one of the very few HVAC guys that knows how to run a clean torch tip! Also sounds like the gas pressures are correct also, I am an aircraft mechanic that had to weld with Oxy-Ac,
@subcoolHVAC24 күн бұрын
Thanks CC, you learn to hear what the flame should sound like if you use it enough. Not much heat needed on this one 🔥👍
@stephenjenner48417 күн бұрын
Only a good tech can make a repair. Any hack can take good equipment and through it in the junk . Those Rheem,Rudd, Weather Kings were good equipment .
@subcoolHVAC17 күн бұрын
The previous company only wanted to replace 😎
@alabamahvacprofessional294623 күн бұрын
Just watched the video, and want to say thanks for repairing the problem. I have 37 years of experience in the field, and most guys these days only want to replace the entire system.
@subcoolHVAC23 күн бұрын
Thanks Alabama HVAC!
@forthefunofit32308 күн бұрын
500 as opposed to 5 grand!!!! of course we want REPAIR!
@ericbaker561923 күн бұрын
Some guys can really perform art with a mixed torch. Good job bud.
@subcoolHVAC23 күн бұрын
Thanks Eric 🔥
@williamgildea83487 күн бұрын
Too many white shirt companies never would have attempted to do this repair. There all about the up sale. Nice repair
@subcoolHVAC6 күн бұрын
Agreed, Most customers would rather repair if it makes $ sense. Thanks for the comment 👍
@zekenzy648624 күн бұрын
Great video. Thank you for sharing. Have a nice weekend
@subcoolHVAC24 күн бұрын
Thank you! You too!
@thesilentonevictor24 күн бұрын
Great craftsmanship tech
@subcoolHVAC24 күн бұрын
Thanks Victor!! 😎
@nicolasmuniz945219 күн бұрын
Looks like the H/F vacuum pump works great.
@subcoolHVAC19 күн бұрын
I’m using it where I can to keep testing 👍
@jasonjohnsonHVAC22 күн бұрын
Been busy....just catching up on videos.....keep it bro...I enjoy the content and the channel
@subcoolHVAC22 күн бұрын
The Heat is On 🔥 Thanks Jason 😎
@stevencossaboon323724 күн бұрын
Nice work Subcool.
@subcoolHVAC24 күн бұрын
Thanks brother 👍
@kamranjutt904020 күн бұрын
Good work👍 but if the leakage is close to metal part of condenser. It is better to carefully melt the surroundings of metal part touching copper u and then solder copper part No callback no complains . I work as an hvac technicion in kuwait .
@subcoolHVAC20 күн бұрын
You realize the end sheet melts at a higher temp than the copper, trying to melt that would destroy the copper. Thanks for the comment though👍
@kamranjutt904020 күн бұрын
@@subcoolHVAC I have done it bro It needs super skills But any way your work is outstanding 👍
@OIC-es6pi23 күн бұрын
Nice work.
@subcoolHVAC23 күн бұрын
Thanks!
@subcoolHVAC23 күн бұрын
Thanks!
@topher863424 күн бұрын
When those aluminum coils started coming out, all the manufacturers claimed they couldn't leak.
@subcoolHVAC24 күн бұрын
A lot of claims were made when r410a was introduced as the new standard, here we go again with A2L 👀
@topher863424 күн бұрын
@@subcoolHVAC give it 10 years and it'll be contributing to something as well
@subcoolHVAC24 күн бұрын
@@topher8634Agreed 100%
@joeyf50432715 сағат бұрын
Nice job
@subcoolHVAC15 сағат бұрын
Thanks!
@RobertTuck-vo8cw24 күн бұрын
Good job. I would bet that the evaporator coil has never been cleaned or even looked at. Also with that number of suspicious spots, the coil will leak in another place.
@subcoolHVAC24 күн бұрын
The evaporator was pretty clean, usually they rust on the end sheets. I’ve repaired many of these condensers like that. It’s the same spot most of the time . It’s best years are behind it for sure. 👍
@SFBay6923 күн бұрын
@@subcoolHVAC Crazy how rusty these evap coils can be. Is there any correlation between strict filter maintenance and leaks in evap coils?
@MarcelHVAC21 күн бұрын
Great job, what was the smoke coming from the condensor? Dirty condensor or was it oil from then refrignant lines burning? Like your oldschool scale, i bet it will survive you!
@subcoolHVAC21 күн бұрын
It was a combination of leak detector liquid boiling off and may have been residual oil on the coil from the initial leak. Yep, the scale will outlast me 👍
@davidnull559023 күн бұрын
Thanks for the video, it was interesting. Was there a huge difference in price between a repair and replacement? thanks,
@subcoolHVAC23 күн бұрын
Thanks David, would’ve cost at least 6x the $ to replace , ultimately it’s customer decision 👍
@nicolasmuniz945219 күн бұрын
Hopefully no fan, capacitor or compressor goes out in the near future they might blame it on you, usually no good deed goes unpunished, I've done a a couple of less expensive jobs to help a customer out and BAM! they call back that their water heater, on other side of house does not work a day after I repaired the a/c, this really happened to me, just told them to go kick rocks.
@subcoolHVAC19 күн бұрын
I did replace the capacitor, no guarantees when in situations like this. The owner is aware of the condition
@TrustedHVACR23 күн бұрын
I would be challenged to do that without burning a hole through the copper … any suggestions?
@subcoolHVAC23 күн бұрын
Yep, clean the u-bend with sand cloth, small light flame and keep it moving with brazing melting over it. I use Stay-silv 6% . Had to stop the nitro because it was popping holes, but got it to close. You can do it. 👍
@Paul-IE-Repairs23 күн бұрын
ive seen several systems installed without a dryer, when the lineset is less than 10ft long. i dont think that is the case in this situation. did someone put a hard start on a scroll compressor smh....
@subcoolHVAC23 күн бұрын
They provide a drier with those units, none was put in when the evaporator was replaced either 🤔.
@DabblelyDiddly22 күн бұрын
funny, most window units still use copper. besides the midea 5k
@subcoolHVAC22 күн бұрын
👍
@jwotham9620 күн бұрын
Forgot the video, but what is your opinion on the compressor jackets? My unit has one and I still need to clean it.
@subcoolHVAC20 күн бұрын
Sound blanket? Not a fan… not sure what that has to do with cleaning?
@jwotham9619 күн бұрын
@@subcoolHVAC didn’t think about it for sound reduction. I asked so when I go in to clean I could address it at the same time if it had a negative effect. Thanks
@subcoolHVAC19 күн бұрын
Gotcha, clean it sure or toss it 👍
@mrsmith511421 күн бұрын
Wish you posted the prices.
@subcoolHVAC20 күн бұрын
Replacement would’ve cost 6-7 times as much if that helps
@mrsmith511420 күн бұрын
@@subcoolHVAC It does :) Thanks for the response. Donno why I watch all these repair stuff, but always interested in the prices. Best of luck!
@bjbuchanan73267 күн бұрын
What was the cost of fixing the unit?
@subcoolHVAC7 күн бұрын
About 1/5 the cost to replace
@stevem108118 күн бұрын
They may save money now, but the unit being that old, they will be paying a lot more in the long run due to it being less efficient and more leaks are likely to show up again before long.
@subcoolHVAC18 күн бұрын
Ultimately customers decision
@divine4fi24423 күн бұрын
They dont make them capacitors like they used to 😅
@subcoolHVAC23 күн бұрын
Definitely not !
@markcotter235523 күн бұрын
15 pounds of refrigerant good golly.
@subcoolHVAC23 күн бұрын
Yep 241 oz. Factory charged
@wayneguy604318 күн бұрын
Who wants to to put in a new 5 ton every 10-15 years for $18k
@subcoolHVAC17 күн бұрын
You could spend that much but not for a comparable replacement to this one . Thanks for watching!
@MindzEnt22 күн бұрын
All depends on how much you charged them, if you go around making leak repairs for 500 bucks of course the owners will go with repairs.