“Heat Treated Frame. Do not drill or weld”. To hell with replacing a rail due to a crack. I’ve done over a dozen of them and not one has come back. Nothing ventured, nothing gained. Carry on Wayno

When your OCD kicks in we all know it will be done right and NOT HALF / ASSED. Great video as always DETROIT MASTER

Nice repair and paint job, not to mention the radiator as well bud! That was a small crack, but better now. 40 or 50 years ago I was motoring along in the 7UP Co. International Loadstar with about 50 thousand pounds of soda pop on board and heard a loud clang/ping noise, thought a bullet went through the cab. Pulled over, discovered the driver side frame rail between the cab and the load body had broken from the bottom flange, all the way to the top flange, which was all that was still together. The crack was about a 1/2 inch wide at the bottom! I motored very gently about 5 miles to the machine shop. They jacked it up til the crack closed. V'd it out and welded it. Then welded plate steel over the crack on both sides and the bottom flange. I was on my way in less than 2 hours.

I will admit, I'm not a smart man. I would have just jacked up the frame until the cracks kissed, grabbed a horrible fright welder, and good enough. But Wayne has shown me why I'm not a fabricator. I'd have never thought of a liner to strengthen it. But, it makes total sense. Wayne, thanks for educating a Gump like me.

We do it twice and we do it nice !!

Hey Wayne, an old painters trick. Instead of using tape to mask all the lines, it's much easier and faster to wrap the tricky stuff in tinfoil and just rape at the ends. Your welcome.

Nice work 💁‍♂️😉👍 Wayne-O!! 💪 Better to have placed a liner inside the frame anyways. Better strength, no doubt. Need to buy some merc from you guys soon, as well. “Ol 2 Stroker” getting it done.

Always great to see Mossy Broke get better with age.

Good thing you were wearing your welding crocs! 🤣

Great video Wayne glad to see Mossy Broke getting some maintenance on the frame and a little touch up on the paint done. Radiator reinstalled it all looks great sounds even better. Looking forward to your next video stay safe Wayne.

Us Old International Transport family members love your content. Great Job

it's a good thing you look over your rig, lot of truckers don't do their pre-trip

Good job, again, Son . You're become a very professient HD mechanic .

Done both rails past the sleeper once upon a time on a K100 with 8 air bags. I decided after that I would let someone else do it next time if there was a need to do that again.

Wayne, when are we going to talk about the elephant that's left the room, I noticed you had the Caddy on Mossy's trailer and out of the shop, is it done, and if so, where's the video, keep up the great work Brother. 🇬🇧

Wayno I really appreciate the amount of hassle/effort that you go through filming and editing this stuff, having to rip apart half the truck just to fix one thing or another...

Nice Job Wayno! Didn't notice the Caddy until I got here. Can't wait to see it! 🍻

You keep your trucks Thank you for your trucks, trucks gather and everything else. I'm sorry about the first one. That was a mistake big but miss messages to tell you you. Every truck that drop bears are in good conditions

Nice job wayne

I absolutlely love that 359!!!

Well done bud

Hey Wayne frames cracks are simple to fix, fish plates and good to go.

How long does jimmy gotta wear the collar of shame?

Luv the liner . You can custom order exact , full , inside or outside , in just about any stregth or thickness , sections from PG Adams . Btw , do you have a Porta-Mag drill press ,,, ? ,,, Common rail 8-V-92 ,,, ?

That's a good old truck never part with it

She may crack somewhere else but it ain’t cracking there again.👍

You’ve done that before, nice job, good for a long time. The frame must have been pretty straight, no movement when you unbolted spring and engine mounts.🇦🇺

Thanks for the show Wayne 🍻

Great great content I've watched your channel a couple of times

Seems to be a common problem on the 359’s mine was welded and sleeve installed before I bought it , one less thing I had to do 👍🏽

I’ve seen a lot of frame cracks just over the rear shackle on the front leafs from stress. I didn’t realize how much stress is on that part. Maybe now it’s time you show how to re frame an old truck and get a little more length at the same time. Good luck!

Looks so much better

Great videos as always ole Uncle Wayno. Keep on keepin on!

insanely cool truck

Love that truck good job

cool repair. also like the tunes at 13:xx

Nice job wayne ! Only thing i would have done different is taper the end tword the rear of the truck so it would not point load the frame.

They probably cut the frame because the motor mounts were bad and rubbed a hole in the cooler. When they changed the cooler it was probably still close so they just hacked up the frame instead of fixing the motor and transmission mount. You always do a great job. Your 359 and trailer are my favorite. One day I’m gonna find me one like yours.

Well done!

Yay engine work, my fav thing to watch

Perfect color of green

Now u gotta repaint all ur pretty bolts lol

THE BIG GUN!!!! WAYNO FOR THE WIN!!!!

Good work Wayne 🤙🇨🇦

Love the truck

Very common on 359s

First time to your channel. Seems you really do good work. If that's Tig welding, can you explain to this old guy how it's better than mig. Could it be a heat thing ? How did you compensate the thickness of the sleeve at the engine mount ?

You're like me always seem to follow the idiots fixing their shit. Looking perfect is not as important as it's done right. You do it right! I always do my own work cause ya can't trust anyone any more. Great work I hope you're proud of this cause it's awesome!

“Heat treated, do not drill or weld” Nunky Wayno- “Hold my drill and my welder”

keep the junk coming 🎉

That's a nice old apple t. V. Can you give that truck and go ambition? Replace clean

I was wondering I’ve seen other channels put grease between the rails to prevent rust and jacking, are you not worried about that

How did you find out it was cracked?

& wow, soo u have to build & weld a complete channel on that front right side ,holy 💩

😂hell I should have called you for help when my flywheel housing and bell housing snapped and dropped the trans on 29 by your house 😂 you were in pa tho

Stay cool wayne

Great video dude, High Fives and beers all round that was good work. I didn't get me a "click" though

Hello there bud 👍✌️

Where did you get your new manifold to turbo pipe? Need a couple for the one I'm rebuilding right now.

replace bumper with deer guard

Is that truck an old one from International Transport that used to be in Rochester, Mn.

Mint!!!

I've seen idiots notch frame flanges to put PTO's on. One time on a brand new double frame IH

I drive an 84 359 long hood and the front passenger side frame has been sleeved at some point in its life it was done right whoever did it but I'm guessing it must have had the same problem you got with yours

You fixed that frame like your from Pakistan..

& u coulda even painted yur engine as well, in that green 💚

What model size is the detroit

Hey man I’m looking for a 453 Detroit or a 4-71 for a project. If you could point me in the right direction I would appreciate it

👍🏻🍻

Whats the tunes at 14/16

That's another petty hassle out of the way.

Comment

Damn it would’ve been cool to paint the radiator in green

When the fuk is mossy broke getting a monster turbski and injectors