Test ride after new bearings and brake pads install 97 honda cr125 2018 front fender and number plate Cut rear number plates Motocal graphics Boyesen clutch and covers
Пікірлер: 55
@marlattmotos3 жыл бұрын
Going to pick up my 97 project this weekend, 12 hr round drive but for 700 bucks it's worth it!
@unbiasedcobra66725 жыл бұрын
Ahh i miss that sound. To be a 16 year old kid again.
@aitosuomalainen72834 жыл бұрын
You can still own one, i have a 1994 cr 125
@tpghl52254 жыл бұрын
Mardej well no shit, but he was just saying
@samkornelis8893 жыл бұрын
I had a 94 when I was 18. 42 now and Im Restoring a 94. Been a fun project so far
@adnan89043 жыл бұрын
Best looking CR ever!!
@crisstylechris649010 ай бұрын
What model of the 2018 front fender and number plate crf450 or crf250?, and what brand of plastics? Acerbis, Polisport, UFO?
@connormyers30253 жыл бұрын
Where did you get that front fender
@IntuitiveUniversity3 жыл бұрын
I was a little sad you didn't do a walk around
@ejb21843 жыл бұрын
Had one loved it wish I didn’t sell it
@wattotatooine Жыл бұрын
same !
@antonyamb21182 жыл бұрын
What typa plactocs did you use for the front end? The updated look looks sweet. Did it bolt straight up to the triple clamps?
@bradsholler18402 жыл бұрын
What aftermarket front fender and front number plate is that? Where did you get your graphics?
@russianhunty66484 жыл бұрын
im the 190th like im going to get one for my first bike.
@jevikfreeman76284 жыл бұрын
just so you know they are a lot of bike for a beginner i started with one and it took a tilt of time just getting used to the bike before i could actually ride it like it was made to be ridden
@t-roymccoy594 жыл бұрын
How much power does a 97 make?
@250yamaharacer5 жыл бұрын
How did the front number plate mount up?
@clillyboostin31385 жыл бұрын
jacob s it mounted right up, no modification whatsoever
@kotariaku4 жыл бұрын
6th gear?
@simppo95865 жыл бұрын
How did you cut the rear number plates? @270 UnderGround
@clillyboostin31385 жыл бұрын
Simppo I just outlined the shape I wanted with painters tape and then cut with a dremel
@simppo95865 жыл бұрын
@@clillyboostin3138 ok thanks
@lorenzodivomano73483 жыл бұрын
Bellissima moto😍😍mi potresti dare gentilmente le misure delle plastiche tagliate posteriori?
@saveriomallemace69912 жыл бұрын
Di che anno è il parafango anteriore
@alessandropalmieri13 Жыл бұрын
how much hp?
@fazerider30925 жыл бұрын
I have a 1997 cr125 too and it has 2018 front plastics too. Where did you get the graphic kit?
@clillyboostin31385 жыл бұрын
FazeRider30 , I custom made them at motocal.com
@fazerider30925 жыл бұрын
@@clillyboostin3138 that thing looks way better than mine at the moment
@gregoenes11383 жыл бұрын
I have a 1997 cr125 and I just bought 2018 crf250 front plastics from UFO but they look different than this and i need a lot more modifications than just 2 more holes to get them to line up. Where did you get the front plastics for your 97?
@enduromosciska37634 жыл бұрын
Fajnie chodzi zapraszam do mnie
@haydenbartolomucci67274 жыл бұрын
Can you show me how you cut the back number plates?
@clillyboostin31384 жыл бұрын
Check out this link. There’s a up close picture of how i did mine. Basically take blue painters tape to get a good visual on how you want it to look and then take a jigsaw to the edge of your tape motocrossactionmag.com/amp/making-a-1995-honda-cr125-better-than-new/
@casfitness51393 жыл бұрын
What bike is the front fender and number plate from
@clillyboostin31383 жыл бұрын
2018 crf 250. You will have to redrill a couple of new holes for the front fender
@daraghevans76374 жыл бұрын
That bike is older than 97. Nice though
@tylerfrench2834 жыл бұрын
I got the same bike it’s a 97
@daraghevans76374 жыл бұрын
@@tylerfrench283 Honda brought out the aluminum frame in 1997.
@spoopytigrams90764 жыл бұрын
Daire Ó hÉimhín i have a 97 and it’s got the steel frame
@daraghevans76374 жыл бұрын
@@spoopytigrams9076 my apologies I stand corrected the cr 125 didn't get the aluminum frame until 98, very nice bike by the way
@spoopytigrams90764 жыл бұрын
Daire Ó hÉimhín an aluminum frame would be nice though lol
@Mellothebello4 жыл бұрын
Where can i order parts that are compatible with this bike (exhaust, fenders, levers, gear shifter). It’s like a f**king treasure hunt lookin for them.
@clillyboostin31384 жыл бұрын
Try Ebay, theres usually a variety on there
@CassWeber864 жыл бұрын
What bars did you put on it
@clillyboostin31384 жыл бұрын
Zeb Montgomery pro taper, not sure which version
@quavo23265 жыл бұрын
You did you get 2018 plastics on that
@clillyboostin31385 жыл бұрын
JACK AVISON just the front number plate and fender. Plate mounted right up and i just had to drill out two more mounting holes in the fender for it to line up. Rear number plates are stock, but cut
@stuwebber5064 жыл бұрын
Was it 2018 fender and number plate u put on yeah?
@Rick-du6xq4 жыл бұрын
Hey man, i am 5”4, do you think the bike is too big for me? (Seat height)
@clillyboostin31384 жыл бұрын
It really depends on what you’re comfortable with. For reference I think they barely sit an inch lower than a crf250
@Rick-du6xq4 жыл бұрын
Clillyboostin how tall are you and how does it fit for you?
@clillyboostin31384 жыл бұрын
GHMX MOTORCYCLES 5’10 I had a crf250 before this and the cr125 was more comfortable for me
@malachi94274 жыл бұрын
im like 5'5 a 1995 cr125 is my size i just sit with one leg over and one leg on the ground.