***1997 HONDA CIVIC Rod Knock Fixed***💯

No video

1997 HONDA CIVIC Rod Knock Fixed💯

Рет қаралды 10,025

Blue loctite OG

Күн бұрын

in this video I fix a rod knock on my 97 honda civic.

Пікірлер: 80

@JuangSubakti 8 ай бұрын

I think I have a same issue. When the engine starts in first time I hear noise from the engine and then gone. And it goes again when I push the gas pedal into 2500 or 3000 RPM. After I watch this video, I am sure that my engine has rod knock and need to be fixed immediately. Thanks for sharing, sir.

@oggarage3459 8 ай бұрын

You're welcome. Good luck with your repair.

@user-qc2wt9uy9e 6 ай бұрын

this helped a lot, my 99 civic is making the same noise noise but worse because i had to use it to go to work. but this gave me a lot of insight of what i should expect, and how i go along with the problems im going to find in my d16y engine.

@oggarage3459 6 ай бұрын

Am glad it did. Keep in mind that depending on how bad your rod bearings are, if your crankshaft is shewed up by the bearings, this may be a temporary fix. My crankshaft was damaged, so what I did was smoothed out enough with sand paper, but it only lasted about 7 months and is knocking again this time am probably just gonna find a good used engine and swap them out. Good luck. 👍

@LonokeCountyResearch501 4 ай бұрын

Did you happen to stall any ?

@TheCarnager Жыл бұрын

Great video. I would change the oil again incase bits are in the other parts of the engine. I think it will last a long time if the oil stays in the engine.

@oggarage3459 11 ай бұрын

We have.

@albertv89ef8 5 ай бұрын

I remember doing this on a tractor once and i haven't really been mechanically inclined to do things like this anymore. Long story short i have this same issues i believe i have a set of bearing in my tool box i will be doing this this past weekend

@lifecaptured011 5 ай бұрын

Was the issue fix after your first week of new bearings, what caused the old bearing to wear out? GREAT vid my friend, awesome step by step process 👏

@oggarage3459 5 ай бұрын

Sorry about the late reply. The original cause for the bearing failure was low oil. Yes, it fixed the problem but only lasted about 8 months due to the fact that the crankshaft was damaged to begin with . As long as the crankshaft is good, it should last a long time. Thanks.

@svenholmgren5015 7 ай бұрын

Thanks for making and posting this, I will probably have to do this and your detailed video will be extremely helpful.

@oggarage3459 7 ай бұрын

You're welcome sir. I hope it helps you out and good luck.

@foreignisdomesticnow2142 2 ай бұрын

Finding good used honda d16y7 engines isn't so easy, at least in my area. May have to turn that crank down 0.10-0.20 on the rod journals, new oversize bearings and run it again.

@youngtradez9489 6 ай бұрын

They can move side to side. Form a wheel to wheel movement. What they can’t do is move up and down front the front bumper to the the back

@AhsanAhsankhan-kf6kd 4 ай бұрын

Thanks sir for that 🎉🎉🎉 people's are learn more knowledge 🎉

@oggarage3459 4 ай бұрын

You're welcome.

@daemonverucchi9501 5 ай бұрын

did youre engine have issues stalling while engaging the clutch prior to the repair? my d16y8 sounds identical to yours before fixing

@oggarage3459 5 ай бұрын

No, but this one is an automatic.

@daemonverucchi9501 5 ай бұрын

@@oggarage3459did you have to torque the crank girdle/ bridge back down to get to the other 2 rod bearings?

@LonokeCountyResearch501 4 ай бұрын

Mine has just started to make this noise but it’s stalling! On another video someone repaired it and it was the Alternator 😩🚨‼️

@infinitidriver7896 Жыл бұрын

Legit it’s fixed👍

@oggarage3459 Жыл бұрын

Yes sir, it is.

@jeffkarr461 11 ай бұрын

Still running good?

@oggarage3459 11 ай бұрын

@jeffkarr461 Yes, sir is a daily driver.still going

@axelmoiseslaham452 9 ай бұрын

nice content

@oggarage3459 9 ай бұрын

Thanks, I am trying to make good videos but is hard sometimes.

@felixnungaray3253 8 ай бұрын

Is it still running? How many miles since you did this? I am currently doing this to my honda pilot. Did you use thicker oil? Mine calls for 5w-20 but thinking if running 10w-30. Since there is some ware on the rod pins.

@oggarage3459 8 ай бұрын

Yes, still running its been about 4 months since I did the repair am not sure about how many miles probably around 5k my son daily drives the car, we're using 5w30, but my uncle when he had the car he was running 20w50 as recommended by his mechanic, maybe I should go back to 20w50 since there's more engine ware now.

@davidluevano3028 5 ай бұрын

So what fixed the problem? Was it the losse one or because it was bad

@oggarage3459 5 ай бұрын

The rod bearings were bad worn-out due to low oil.

@lucasornelas6113 3 ай бұрын

Why don’t you just replace the crankshaft if the compression on cylinders are good. My mechanic said if the compression is still good on all cylinders you can just replace the crankshaft or take it to a machine shop if it’s not severally damaged and have it grinded. To much work? I know you said it messed up again after 8 months.

@oggarage3459 3 ай бұрын

I mean, yeah, it is a lot of work, and a use crankshaft costs around $ 300 or more, which is almost as much as a use engine cost. So we'll see what happens. I'll probably drop a shorter video showing what it looks like the second time I already did the bearing again, and it runs, but probably not for very long.

@bradleymiller8623 10 ай бұрын

Nice video OG!

@oggarage3459 10 ай бұрын

Thanks, not the best, but if it helps, I am glad.

@rishardriveravalles 5 ай бұрын

Hello! Are the torque different for the Y8 motor becuase yours is the Y7 motor thanks!

@ClaytonroystonDeKlerk 6 күн бұрын

Does the oil light stay on

@oggarage3459 6 күн бұрын

@@ClaytonroystonDeKlerk nope

@bradleymiller8623 8 ай бұрын

Bro how did tou remove the top bearing of the main bearings with the crankshaft still in the car?

@trashboatjc Ай бұрын

spin the crank by hand

@trippieacid6251 19 күн бұрын

@@trashboatjc do I have to remove any belts first?

@oggarage3459 18 күн бұрын

No, you don't just remove exhaust that runs under the oil pan, remove the plate cover attached to the transmission, then all the bolts to the oil pan and use a 19mm socket to spin the engine when removing the bearings. ENGINE SPINS TOWARDS THE FRONT OF THE CAR.

@timduncan2531 4 күн бұрын

You did a fantastic job filming this peice. Congrats, someone really needed to film this procedure for people to see. It's the correct way to save an engine. Gas stations use to make tons of cash. Charging people for rebuilding their engine when all it is. Is this!!

@timduncan2531 4 күн бұрын

I bet it's still running too!!

@mojopojojojo2639 10 ай бұрын

Hi there, not sure if mine is rod knock or something to do with transmission. But it only do it's knocking when put in gear. But you can bearly hear it. If the aircon is on not possible to hear. She's been like this for so long driven about 30k kilometers and no change. It didn't gets louder it disappeares in some instances. You think it's a rod knock?

@oggarage3459 10 ай бұрын

Maybe something else rod knock usually never goes away unless you fix it.

@mojopojojojo2639 10 ай бұрын

Right. Great video.

@litare4328 9 ай бұрын

@@mojopojojojo2639piston slap when under load idk, do you have the answer?

@mojopojojojo2639 9 ай бұрын

⁠@@litare4328not yet. I shall have it checked by a pro.

@joelestevez2277 8 ай бұрын

How long took you from start to finish?

@oggarage3459 8 ай бұрын

4 or 5 hrs, maybe total. Am sure it takes less time if you're not making a video.

@donniesmith512 Ай бұрын

I really liked the 📹 🎥 📻 📸 thanks

@javaughnmannings3378 7 ай бұрын

Where can I get the bearings to buy ?

@oggarage3459 7 ай бұрын

I bought mine from O'Reilly. They're the standard size.

@Thundercloude 2 ай бұрын

Is the rod bearing acl better than the factory?! Need help

@oggarage3459 2 ай бұрын

Am not sure brother. I bought mine at O'Reilly.

@user-jp3br8bl2m 3 ай бұрын

How long did it last

@aarodedoon8757 2 ай бұрын

Hey so i replaced my bearings with the new ones, but my engine wont crank. I tested with my hand but it just wouldn't move. Any ideas?

@oggarage3459 2 ай бұрын

Did you put oversize bearings or standard bearings?

@aarodedoon8757 2 ай бұрын

Standard

@ramirocastillo1452 2 ай бұрын

Hopefully you measured with Plastigauge? Sounds like oversized bearings went in or got over torqued. Something is binding up.

@oggarage3459 2 ай бұрын

@ramirocastillo1452 yup, probably oversize bearings

@Xully 4 ай бұрын

W ❤

@E_Wideman_Communications 5 ай бұрын

Man my car just start making this noise 20 mins ago

@ini1337cool 5 ай бұрын

did u fix it yet?

@E_Wideman_Communications 5 ай бұрын

@@ini1337cool it got worse smh may need a new engine I’ll know one my mechanic tells me

@oggarage3459 5 ай бұрын

Yeah, since the crankshaft was too damaged when I did the repair. It only lasted about 8 months, and it's down again, and this time, we're looking into just replacing the engine But it ran well for about 8 months.

@ini1337cool 5 ай бұрын

oh god, wish u luck@@E_Wideman_Communications

@ini1337cool 5 ай бұрын

Thats pretty good for how much damage there was i feel like and its a honda so it wont be too expensive to change the engine hopefully. Thanks for the detailed video btw its probably gonna help me a lot if i decide to change mine. Currently have a problem of smoke coming out of my dipstick hole after an oil change for some reason. I really hope its not the rings but if it is ill change out the rod bearings as well :D@@oggarage3459