$200 WaveRunner 3 Rebuild

Рет қаралды 14,161

Күн бұрын

Finally back with a long form rebuild video. This time I picked up a 1993 WaveRunner 3 for just under $200 that came with a toasty rear piston and needed a complete top end rebuild.
0:00 Intro
3:11 Oil injection removal
5:42 Pulling the engine
10:08 Removing old pistons
13:18 Inspecting cylinder
15:38 Power-washing
18:00 Siphoning old fuel
19:46 Removing and cleaning fuel tank
24:10 Prepping engine surfaces for reassembly
26:58 Oil block kit install
28:09 Top end installation
38:15 Engine installation and alignment
43:06 Exhaust installation
46:44 Odds and ends install
50:21 Test fire
53:54 Test drive and outro
Social Media Links
Facebook: / ruralplayground
Instagram: / ruralplayground

Пікірлер: 31

@cub1009 5 ай бұрын

Great work! I love seeing people fix up these old 2 strokes.

@tremorist Ай бұрын

Nice piece.

@stowaway475 Ай бұрын

Good job very good video

@Jonh707 Жыл бұрын

Appreciate you making these videos! Very helpful!

@albertodias5900 Жыл бұрын

Nice job man those are two dope looking and reliable skis!

@mikeperry2814 Жыл бұрын

Nice work! I have 3 of those and just need to replace an outboard bearing in one of them. *Be sure to stop engine when shifting into reverse/forward. Have fun! Oh, sit and lean forward and make a sharp turn at med speed to do a donut!!!! (hold on tight) Whoo Who!! 😆

@SuperLashawnn Жыл бұрын

great job

@stash420 Жыл бұрын

Good job bro going to do that to my 1992 Yamaha WaveRunner, 650

@wyatterickson-sy2td 9 ай бұрын

Great vid, love the channel. I just bought a 1990 Yamaha waverunner lx which rips but is super janky with 2 people

@RBSkellington Жыл бұрын

You can just pinch those rings up into the cylinder, there's gaps on either side that your fingers can go. No need for zip ties holding them

@432derrick Жыл бұрын

getting ready to do the top end on a 93 yamaha vxr 700 pro im getting 130psi on one and only 45-50 on #2

@JetSkiBuyFixPlaySellChannel 5 ай бұрын

Is the compression low on the VXR? The difference in performance might be due to the pump size. Some of the Yamahas had 133mm pumps so a rebuild might not make a big difference unless it's low on compression.

@user-dr2qv8hx3r 11 ай бұрын

Hey man great work on that thing! I have the exact same jet ski and it flipped in the water a couple years ago and I havent been able to get to run since... It ran absolutely perfect before that moment. You used to be able to click the starter and it would start immediately... I can get it to start up and I can rev it but it shuts off once it comes back down to idle .... Is there anyway you know what I need to do ? Thanks a ton

@joshuabarberi3192 10 ай бұрын

check your fuel reeds and make sure they aren't messed up, also check the carb make sure the internal fuel filters isn't dirty.

@manusengelbrecht9959 6 ай бұрын

Did you redo the Carb?

@patrickduncanjr.6847 Жыл бұрын

Hey great video…..I have a 94 that hasn’t run in 3 years should I just drain the oil and gas. Put fresh in and it should fire up?

@RuralPlayground Жыл бұрын

Yeah, get all new fluids in it and make sure everything is where it should be.

@mattheweburns Жыл бұрын

Proper maintenance makes a difference between 300 hours being a death sentence and being brand new. No ethanol never. And apparently it is better to leave fuel in these with stabilizer that is to let them sit dry like other small engines.

@tjn2254 3 ай бұрын

Where do you live? Have any wave runners for sale?

@Huntersprojects Жыл бұрын

Found a 1990 wave runner 3 for 500 bucks with trailer is it worth it the guy says in needs lots of work not sure what that means are these simple never worked on one before I assume it’s like a lawn mower but with a jet and it’s on water

@TySlimVlogs 4 ай бұрын

What do you do with the oil pump? Are you going to cap off the lines or just let it pump nothing? Thanks!

@RuralPlayground 4 ай бұрын

Oil pump was completely removed and replaced with a block off kit from sbt.

@DanLemire Жыл бұрын

Just curious.... whats the cost on having a machine shop bore them out? I have a simular projet lined up. Also I have to say this.. Your edits are awesome. I like that you showed forgetting the throttle cable. It's not easy..lol

@RuralPlayground Жыл бұрын

It was 60 bucks for the shop I used.