2001 Dodge Ram 1500 Intake Manifold and Plenum Gasket Replacement

Рет қаралды 2,809

Күн бұрын

In this video, I replace the plenum plate and gasket on my 2001 Dodge Ram 1500 with the 5.9L V8 Magnum Engine.
This is a well known common issue with all Dodge Magnum engines and applies to the 3.9L V6, 5.2L 318 V8, and 5.9L 360 V8.
Replacing the Plenum gasket and Plenum plate is not a very difficult job to do and really only requires some basic hand tools as seen in the video. Altogether this took me about 4-8 hours to complete so by following the steps outlined in the video, it shouldn’t take longer than a weekend to complete.
I really hope this video was helpful and thank you for watching!
Link to parts in video -
NGK Spark Plugs - amzn.to/3UUsJYI
NGK Spark Plug Wires - amzn.to/3KkcrmZ
Plenum Gasket "No Aluminum Plate" - amzn.to/4aG52ci
Belt Tensioner Assembly - amzn.to/3UQRZim
Thermostat Housing - amzn.to/3R1GgfQ
Thermostat - amzn.to/3Vchzj8
Oxygen Sensors - amzn.to/3KBQSP3
Idler Pulley - amzn.to/3WVH49V

Пікірлер: 18

@SwanCanFixIt 2 ай бұрын

NGK Spark Plugs - amzn.to/3UUsJYI NGK Spark Plug Wires - amzn.to/3KkcrmZ Plenum Gasket "No Aluminum Plate" - amzn.to/4aG52ci Belt Tensioner Assembly - amzn.to/3UQRZim Thermostat Housing - amzn.to/3R1GgfQ Thermostat - amzn.to/3Vchzj8 Oxygen Sensors - amzn.to/3KBQSP3 Idler Pulley - amzn.to/3WVH49V Permatex Black Silicone - amzn.to/44VfoDO

@jeSuperfly 3 ай бұрын

Absolutely tremendous video. Cleanly done too!

@stevenanderson6658 12 күн бұрын

Nice video. Great job

@taywooten77 27 күн бұрын

Great video!

@user-dt7zs3jk6c 29 күн бұрын

Where are you located, and how much labor cost for you to do a 2001 Dakota 5.9..?

@---RON---- 18 күн бұрын

Surprisingly my blown plenum gasket caused smoke on start up. I replaced the valve seals first thinking that'd forsure be the fix but definitely not

@eltrompudo26 18 күн бұрын

Will the plenum gasket cause lack of power to the engine? My truck runs good. But it feels like when I'm on the highway won't respond even with the gas pedal on the floor. It goes on the speed but slow

@WanderingRobotStudio 3 ай бұрын

Hell yeah

@kyle5555 3 ай бұрын

Were your spark plugs fouling up before you changed this out? I have oil down there and have to change my spark plugs about every 4 months, and only the 4 on the right hand side lol

@jay-gu6pl 2 ай бұрын

isnt the crank position sensor easier to get to with the engine stripped down? I've never changed one but heard its a shitty job.ting ready to do the hughes plenum replacement and bought a cps figuring it would be easy to.

@SwanCanFixIt 2 ай бұрын

Yes, it would be much easier to get to it with it stripped down. I also thought about changing out the water pump and timing chain while I was at it given those would be easier to get at as well, but ended up putting that off for a later time. Good luck on changing everything! Hope the video helps!

@liammccarthy2277 2 ай бұрын

How many miles on the engine? Mechanic said my intake manifold gasket needs to be done (for ~$3500). But, engine has 255k...

@SwanCanFixIt 2 ай бұрын

This engine had 206k miles on it when I did this. Should be able to get at least another 100k miles out of it now. $3,500 is probably not worth it if going that route with that many miles. If you do it yourself with the Hughes plenum kit and new coolant, that will only cost you about $250-$300. Not a super hard job just takes a solid weekend to do. Hopefully the video helps if you end up doing it yourself.

@dean0233 3 ай бұрын

Did you have any performance issues you noticed before doing this?

@SwanCanFixIt 3 ай бұрын

I noticed that the truck was very sluggish when accelerating before changing it. Since then it seems to have a lot more power and it’s not burning oil anymore. It was burning about a qt of oil every 1000 miles.

@3c_guitars 2 ай бұрын

Did it feel like the truck had a parachute attached before replacing the plenum gasket

@SwanCanFixIt 2 ай бұрын

Yes, it definitely felt very sluggish when initially trying to accelerate like you are describing. I also did the spark plugs and wires while changing it out so that could have helped a lot, but overall after changing it out it feels a lot more responsive when accelerating.

@3c_guitars 2 ай бұрын

@SwanCanFixIt mine wont even do a burn out lol