Did mine today. Pro Tip: You only have the remove the clamp/hose from the radiator. Don't struggle removing the the clamp/hose from the thermostat, just take the bolts out and pull the unit out with hose attached. A lot easier to work on clamp when it's out.
@paulwoodman51313 жыл бұрын
And the hose and housing is marked in order to install the hose to the housing on the bench. Or it should be, if not you can mark them according to the old one. And the fender liner comes out for access.
@StrawberryRazorz666 Жыл бұрын
Good advice
@lilibethdoherty2952 жыл бұрын
Removing the Tire made it so easy to get to and was very easy to unbolt .The Two Bolts actually were not very Tight at all. The O- Ring may have shrunk so much the tension on the Thermostat housing was greatly reduced. Thanks again for saving me a trip to the overpriced repair shop!
@bamafever923 жыл бұрын
Hey man first of all thanks for the video it helped me out a lot! I had this same exact issue and I changed out the thermostat my temperature gauge is working now but it’s still showing the check engine light and my ac still isn’t working do I need to go in and clear the code? Or should it go off on its own? Thanks!
@jessemora1822 жыл бұрын
Nice video thank you Question.... what lift are you using weredid you get it at
@Ephesians-yn8ux2 жыл бұрын
About to do this to my truck today. Thanks for the heads up. Nice worship music playing also!
@Joe-vc6ml3 жыл бұрын
Thanks for the vid, love the music in the background too!
@sandyblue4235 Жыл бұрын
Your garage is too neat
@joseislas84603 жыл бұрын
Amigo thank you very much
@alexlaverick61112 жыл бұрын
Don't bother with pulling the hose off the thermostat. Just loosen the bolts and pull the hose and housing out the wheel well. It makes it easier to reinstall the hose so it lines up with the mark on the housing I don't remove the hose from the rad either. I loosen the clamp and then work a hose loosener in between it and the fitting which allows a small controllable stream of water to drain the system
@bricelewis7869 Жыл бұрын
I removed the hose from the radiator on my end cuz I was draining the coolant at the same time. I figured while I was changing the thermostat it would be a good time to flush the system and change the coolant out with new coolant.
@StrawberryRazorz666 Жыл бұрын
Thank you
@bobbyjones-uv5cn3 жыл бұрын
Mine has a sensor plug on it.I can't get it off. I have a 2015 colorado.
@alexandera4123 жыл бұрын
Excellent video, thanks for the time you invested, I had the thermostat replace and my 07 Colorado temp goes almost 3/4 hot, it has new radiator, hoses the right coolant and I don't know what to do any more. I stalled OEM parts, if you have any advise, I would appreciated, nice music by the way
@oscars-autorepair32363 жыл бұрын
Good afternoon Alexander, try replacing the engine coolant sensor see if that helps.
@th3kings983 Жыл бұрын
New thermostat making the engine run hotter there’s a whole page about it. It happen to my also replaced water pump fan clutch and thermostat and all the sudden the truck it’s almost at 3/4 nothing wrong with it was just maintainer for the year and mileage.
@karenglass938411 ай бұрын
Hiw long does this take
@icaanul2 жыл бұрын
Seeing other sources that say the torque is 10 ft lbs.
@sirpancakes2 жыл бұрын
How long did it take you .
@oscars-autorepair32362 жыл бұрын
About 45min
@sylwesterskoczylas10253 жыл бұрын
Hey. I bouth Thermostat SKP manufactured is good? Better buy original? SKP "made in China" original too?
@oscars-autorepair32363 жыл бұрын
I would recommend stick to the oem part. I changed aftermarket parts like candy, they are good for a few months but they start to fail. Save urself the headache and get the acdelco part.
@sylwesterskoczylas10253 жыл бұрын
@@oscars-autorepair3236 thanks for reply. I try mount this and if not good buy original. In poland some parts cost too much
@dylonbaer9853 жыл бұрын
What’s the name of your special tool?
@onepunch7632Ай бұрын
Hose clamp pliers
@sandyblue4235 Жыл бұрын
Is your antifreeze red
@farstrider79 Жыл бұрын
All Chevrolet is. Dexcool
@thunderroad72893 жыл бұрын
Lol yea get the gm part made in Mexico
@scottshelley123 Жыл бұрын
You can actually do it easier by removing alternator ,serp. belt and fan shroud...you can gain access to both bolts without tire and shroud removal
@larsonny779 ай бұрын
Lmao you ever try to remove that shroud? Biggest pain in the ass putting it back in.
@delllong694119 күн бұрын
Sorry but wrong the hose stays on the thermostat and it better go back on the dye mark or it's never gonna fit