2009 Audi A4 2.0T Engine Misfire Fix And Intake Manifold Removal

Рет қаралды 96,182

3 жыл бұрын

2009 Audi A4 2.0T Engine Misfire Fix And Intake Manifold Removal For Business Contact :
Nathan's BMW Workshop
Po Box 115 Altenburg Mo 63732
nathan.youtube@yahoo.com

Пікірлер: 110

@mikimiki195 3 жыл бұрын

Yeah Nate is back fixing stuff 👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻

@DuaneMoore 3 жыл бұрын

Audi are such beautiful cars( the new ones) nightmare (rs6 ) to work on . Good job Nate Jack of all cars .

@JohnGriffithJr 3 жыл бұрын

OK, yes this was a good instructional video. No skipping the painful, tedious steps. No time lapse videography. The real thing just like you were there getting your fingers dirty. Thank you.

@shotbyqory3161 3 жыл бұрын

Right

@narreshsingh2346 Жыл бұрын

Your saved my life with this video

@jessesward9429 3 жыл бұрын

Just got done will a full day working on cars, time to watch Nathan work on cars

@ButtKickersReviews 3 жыл бұрын

Same lol

@robertoalvarez7960 Жыл бұрын

Very thorough thank you. Glad to be on board.

@gerardogarcia-et2pb 6 ай бұрын

You are good in all the explanation clear talk.

@ranbirrana3993 Жыл бұрын

Your video is informative. Curious what causes to replace hpfp?

@231mac 3 жыл бұрын

Try to disconnect the injectors/fuel pump before doing a comp test as the raw fuel help seal the rings and artificially inflate a cylinder's PSI.

@samoniumuziejus 2 жыл бұрын

I get P2015 but the manifold flap looks fine, what othrr parts could that code signal ? Manifold sensor itself ?

@jonowen6612 3 жыл бұрын

Good video! Thanks!

@R3MILI 3 жыл бұрын

Ive a a6 2007 2.7 diesel with manifold intake problem . Ive done all filters and oil change , but it consume 10 lit for 30 km in city . I dont know how much has consumed before becose ive buy it 1 month ago , with 255 000 km . In highway it consume 8 lit . It has even some code rfor injector 2 3 5 . If i use diesel moly purge directly in fuel filter and if i buy new intake manifold , will it consume 30% less or not ? What do you think , give me any advice

@Lovely_planet 2 жыл бұрын

"ECS Junk" i lost it hahaha

@oso2916 2 жыл бұрын

Do you need to program the fuel injectors ?

@GiotheGhreat 3 жыл бұрын

Hi. My 2016 A5 2.0 is jerking when I come to stop. Sometimes it goes away and comes back. No CEL or pending codes. What to do when there is NO CEL on? Should I keep driving it? I did common maintenance + New coils and spark plugs. Ca has 50K miles only. I never floor it or race because is a sedan

@fastboatster 3 жыл бұрын

Just wait till you get to do a suspension refresh, you might be having a lot of fun with upper control arm knuckle pinch bolt.

@Jacob-ug5hy 2 жыл бұрын

Yeah I had to replace my whole spindal on that one. Put anti seize on the bolt and has came off smooth so far

@robertoalvarez7960 Жыл бұрын

Cake compared to this

@jppoolcleaners 2 жыл бұрын

What was the issue that caused the Misfire? Was there a crack in the intake manifold that was causing the misfire?

@gutzu265 2 жыл бұрын

4.00 is that excess fuel shooting from the cylinder with the bad Injector?

@sufyanumar4663 Жыл бұрын

My 2009 Audi A4 Avant is misfiring on idle but slowly starting to misfire when I'm driving now. Will I need to change the injectors?

@R3MILI 3 жыл бұрын

Hello , ive a a6 2007 2.7 with bad intake manifold code . Car consume 10 lit in 30 km city , does it consume so much becouse the intake manifold ? In highway 7lit/100km

@jerryx2000 Жыл бұрын

Hey man I want your honest opinion. I own the A4 B8 2.0 TFSI since 2011. The engine was using 1l oil per 1000km. I got a new Audi motor in 2014 for free as the car was under warranty. Since then no oil usage, just the cooler went bad in 2020. Now the car has 190,000km & it is running perfect. Would you sell the car or keep it for another 200,000km?

@FloridaBikeSupplyOnline 3 жыл бұрын

@ 18:33 Do you know the name of the valve under the oil filter? I've been trying to find new o-rings to fit it, but thinking I'll just buy a new one. The closest I've found to a name or part number is "oil filter adapter valve" for a 2017 A4. I have a 2011 a4. Great video! Cheers!

@robertoalvarez7960 Жыл бұрын

Oil, filter, housing gasket

@kirkbanton9181 3 жыл бұрын

It would be nice to see you working on more customer vehicles.

@quincybattle9458 5 ай бұрын

I have a 2013 a6 3.0 supercharged that’s misfiring all on bank 1 and it’s displaying all the symptoms of this car, any ideas ?

@blakeamathews10 3 жыл бұрын

Sorry if this isn't the best place to ask for help lol, but I'm at my wits end, I've been troubleshooting, fixing and finicking with her for months now. I have a 2013 e93 with the n55. Randomly one day a while back she started having a random misfire in just cylinder 6 with no real reason as to why, and a rough idle, I've replaced the spark plugs with 2 step colder, the ignition coils are brand new and that seemed to help a lot, ran injector cleaner through her a couple times, and New MAF, I am in a pretty serious club so she gets her spirited driving in almost every week, and tats what through me off, the misfire is totally random. And only ever at higher rpm at higher gears, I have a manual so I can confidently say now it only happens sometimes above 4 rpm in 5th or 6th gear and almost always pops up if I'm going up a hill, I'm running jb4 and have never seen any codes to point me in a direction which is also wierd to me, catless dp's, and bms intake are the only major engine mods I've got in her, the rough idle I'm fine with, I can live with that, but I've been chasing this misfire so long I'm resorting to commenting on KZfaq, please someone help lol

@andyb6851 3 жыл бұрын

There are some youtubers like BMW Doctor that do paid consultation, much cheaper than going to a US mechanic. I'd really suggest going for something like that, just do the usual like smoke test for vacuum leaks, look inside and compression test cylinder 6. Also do what Chaminda said.

@tonka10r99 3 жыл бұрын

Did you gap the spark plugs to the correct inch?

@bootneylee9802 2 жыл бұрын

My man welded the plugs and oil filter in. 🤣😂

@andyb6851 3 жыл бұрын

That went nicely, when I saw the spark plug being on so tight I had a feeling there will be other surprises. So there's no use in trying to clean the injectors, better just buy new ones?

@NathansBMWWorkshop 3 жыл бұрын

They are cheap enough not worth cleaning , and prob has plunger issues inside the injector

@christoledo5217 Жыл бұрын

Did you had to program the injector?

@ddubz6356 2 жыл бұрын

"Its a baby engine" *struggles with spark plug* 😂

@wingitreview 11 ай бұрын

Lol I laughed too

@visualmanagement7662 10 ай бұрын

I got 400hp to the wheels with my baby engine 😂

@ruslik91 Жыл бұрын

Why you testing without remove all spark plugs from 1st cilynder. if there air bridge between 1st and 2nd cilynder you can see wrong compression bars.

@ericbloomquist9040 3 жыл бұрын

Aftermarket Boost Controller?

@tonym-so4tt 2 жыл бұрын

2010 a4 I’m in the military stationed in Korea and car runs rough and in traffic it cuts off when rpm are low,I brought it to audi here and the can’t find the issue.I had changed camshaft and crankshaft valve and cleaned the throttle body coil packs cleaned fuel pump and injection still having issues please help thank you

@ShowMeWhatINeedToKnow 3 жыл бұрын

How does he drive at night?

@vexican8132 2 жыл бұрын

What was the issue and the fix?

@Blankman-jq6xu 8 ай бұрын

Hey bro..long time man you might not even remember me. You began with the bmw green X5. I had the 06 fully loaded. I was at ground floor of your shop being built i watched it as you let us watch the build process😁 I didn't know you were into working on Audi vehicles too. Send me your email info again i lost access to my old email due to being hacked.

@fastboatster 3 жыл бұрын

Another note on how easy it is to work on b8 Audis is that on 2010+ you’ll officially have to disconnect the ac lines to replace the coolant radiator or grind of some tabs on the radiator. Also, if you haven’t noticed, there’s no valve cover in a BMW sense of this word. It’s an integrated valve cover/cam girdle, if it starts leaking, then you’ll have to mess with locking the camshaft. While easy for a seasoned mechanic, a lot more intimidating for an average diyer. I could go on, but I wouldn’t get so excited about this cars so quickly.

@NathansBMWWorkshop 3 жыл бұрын

lol these are not hard jobs, remember all the past cars i had and past videos, not much scares me anymore

@fastboatster 3 жыл бұрын

@@NathansBMWWorkshop yes, but the point is that it WILL be intimidating for a more novice person. I mean, it’s cool but getting some brackets holding some rubber air guides in the way of ac lines so that you can’t pull the evaporator out of the brackets on the radiator without disconnecting the lines is not stupid. It’s actually very smart and malicious, and that’s kind of quintessential VW group. 2009 - lines allow to unclip it, but 2010 the manual says “ac lines have been improved”, need to disconnect to replace the radiator. And it’s not just the labor, parts such as control arms, engine mounts are quite a lot more expensive. No, it’s just not the same as my e90 where I was able to pull the radiator out on the side of the street without jacking the car up or replace the belt in 15 mins doing it first time ever and in the parts store parking lot. Another thing is that they have timing chain issues and oil consumption, and all this is just too much to bother for a car which is not better driving and engaging as an rwd e90

@Tweakin Жыл бұрын

@@fastboatsterI’m fairly novice.. oil change here, brake job there. This legitimately looks as simple as it gets tbh especially considering

@fastboatster Жыл бұрын

@@Tweakin yeah, so is oil change on many bmws or brake jobs. Speaking of the brake jobs, b8s already have an electric parking brake, need a diag tool or need to apply some voltage to the parking brake motor to replace the rear pads without breaking anything. 3 series up to g series still have normal parking brake. Bottom line, own and drive the car you like but be aware that Audi is not really easier than BMW

@Mattmazz77 3 жыл бұрын

Yeah you're right about ecs tuning some of their own stuff is not quality. That fitting for the boost gauge or controller was causing a vacuum leak. Plus the boost gauge I got from them came with shit vacuum lines, the little adapter that converts analog boost to a digital signal is straight garbage!!!!!

@grantbradley5084 2 жыл бұрын

My 2012 A4 2.0 had a misfire. The motor was emitting a knocking noise from the front of the motor. Mechanic replaced the rocker arms and lifters. Knocking sound still there. After scoping, was determined cylinder #1 is scored, requiring replacement of the motor. Rings, pistons and timing chain replaced at 57K. Engine failure at 67k. New long block installed, issue addressed.

@uptownclarkson6662 Жыл бұрын

Does your car run good after the engine replacement? I have the same problem but don’t know if I want to waste the money to fix it

@mickmolloy6594 Жыл бұрын

So did you replace all the injectors or just cylinder 1 injector?

@snoopy5736 4 ай бұрын

All

@edgarmartinez3052 Жыл бұрын

Where u get the injector

@jessesward9429 3 жыл бұрын

Can a stuck injector hydrolock a cylinder?

@andyb6851 3 жыл бұрын

yes

@timgilman2495 2 жыл бұрын

If you cycle the key enough times to put "that much" fuel into the cylinder without turning the engine over, yes. Expect the engine oil to be contaminated by raw fuel as well.

@domanebyrd-white1140 Жыл бұрын

Hey Nathan I need your email and number again brotha....I thought you only worked on BMW vehicles. I just got a 07 Audi Q7 with 3.6L V6 quattro premium package suv. Do you have any vids on the EPC Light ?

@vexican8132 2 жыл бұрын

I'm having this EXACT issue, and i've been chasing this problem everywhere. Could you tell me what you did to remedy the problem?

@NathansBMWWorkshop 2 жыл бұрын

Fuel injectors

@isleseayou 2 жыл бұрын

If you’ve already replaced your coils,plugs and injectors and still having issues, replace your turbocharger wastegate. Like $50 on Amazon. I did this before injectors and it solved my issue.

@jordanacohen9555 3 жыл бұрын

Nathan, get yourself a Milwaukee Electric Hand Ratchet.

@stefanczechorskidds8435 Жыл бұрын

With the injectors plugged in electrically and fuel line connected and the manifold pulled back as you had it, it would have been informative to see what happened when you turned the key to ON. Any good injectors would not spray or shouldn't spray fuel . Definitely have a rag over number one suspicious injector!

@evilenergy7121 2 жыл бұрын

Remind me never to buy one of these....lol

@Morphz_Unlimited 2 жыл бұрын

Only if it has the 2.0t engine.

@GeorgeAusters 3 жыл бұрын

I would have put the car back to standard, could be the tune that is over fuelling

@EXOVCDS 3 жыл бұрын

Lack of residual pressure in the fuel rail is to be expected with a leaky injector, no? You seemed surprised about that.

@robertoalvarez7960 Жыл бұрын

He did great explaining it as a person that just started or is learning don’t be rude man

@Aikorslickbacks Ай бұрын

It’s a little low on coolant too

@klubstompers 4 ай бұрын

You could tell injector #1 was stuck open, because when you removed the injectors, fuel was leaking out of it. This wont happen, unless the injector is open.

@410kane Жыл бұрын

Had the same problem. Cylinder 1 misfire. I changed the plugs no result. Switched coil pack between 1 and 2 cylinder no result. I'm assuming it's an injector clog

@hectormedina2778 8 ай бұрын

Did you figure out what it was?

@410kane 8 ай бұрын

@@hectormedina2778 ended up being a bad battery. Didn't have enough juice to run the engine and accessories. All the lights on the dash disappeared and the car runs beautiful again.

@hectormedina2778 8 ай бұрын

@@410kane Dang so you got lucky. My car as a really rough idle and it also makes a really bad ticking sound. I’m going towards fuel injectors but not 100% sure yet.

@410kane 8 ай бұрын

@@hectormedina2778 hmmm. They say the 2.0 engines are known to get carbon build up on the valves because direct injection engines don't have injectors on the intake manifold to help keep the valves clean

@hectormedina2778 8 ай бұрын

@@410kane what would you recommend? Try fuel injector cleaner?

@dryhollowgarage397 Жыл бұрын

Probably no pressure due to the injectors stuck open.

@TjeRod 3 жыл бұрын

TFSI....oh boy.... :-/

@gregcowart8229 3 жыл бұрын

Nate with all do respect my n54 motor is a hell of lot easier to pull injectors than that one no disrespect dude

@NathansBMWWorkshop 3 жыл бұрын

But then you have to code the New bmw injectors and they are not $200 for new ones

@fastboatster 3 жыл бұрын

Coding the injectors is not a problem at all, everyone watching this or any kind of bmw channels knows how to get INPA/ISTA and code those injectors in. As for the N54 injector prices, they got jacked way up not in the least because all the kids like the one with this VW started to buy them because “it’s a German 2jz” and all the KZfaq hype.

@NathansBMWWorkshop 3 жыл бұрын

@@fastboatster ah yes but you still have to code them and most people cannot do that and most shops won’t do that , remember this is more comparable to a n20 engine , and no electric water pump on this one , and rainwater don’t back up and flood the ecu either , I have had a lot of Audi’s in the past , a6 and TT’s ,all cars have their issues and some are just more reliable than others depending what engine , at 100k miles they all need major service which most of them never get regardless of brand

@fastboatster 3 жыл бұрын

@@NathansBMWWorkshop yeah, I guess we can argue for a long time about this and not come to any agreement. But I just want to say that having both one b8 chassis car (s4) and one e90 328i and talking/reading the forums for either platforms, I’m not so hot on the b8 platform anymore. B8 came in in 2007 in Europe so really similar timeframe to e90, and while Bmw gave us pretty much the last of its kind NA I-6, VW/Audi came with 2.0t econobox engine. And for the turbos, n54 is a class or 2 above 2.0t and really compares to 3.0tfsi in a much more expensive and also somewhat troublesome b8 s4. Anyways, the conclusion is that it’s great to have different cars on the channel and perhaps it takes time to really gauge what the car really is.

@gregcowart8229 3 жыл бұрын

Then theirs that LoL but just changing them is definitely quicker

@fordnatic6011 3 жыл бұрын

Use your strong hand 🤣

@NathansBMWWorkshop 3 жыл бұрын

I was lol

@tech42long35 3 жыл бұрын

Autolite's ?? Jee Zuuus.. Enjoy the repair-shop type thing tho.. other ppls stuff, helpn the community out, especially.. saving good German machines from abuse. Liked it..

@kinderutz 2 жыл бұрын

Put on some weight, eh? Pandemic times 😄

@tech42long35 3 жыл бұрын

Exactly why you Never buy a decent car from a kid. They "know everything" fiddle with everything, and ruin everything, especially daughters-lives hahaha... what.. 560ft-Lbs on the spark plugs.. ya.. gotcha.

@visualmanagement7662 10 ай бұрын

Speaking from a kid with a decent car. We do know everything 😂

@deejay4837 4 ай бұрын

Almost ALWAYS cylinder one.....Arggghh!

@ericclinch 7 күн бұрын

Exact car to the t lol

@Lovely_planet 2 жыл бұрын

the boost controller killed it. those cars arent meant to have them unless you have a big turbo and then you probably arent doing that on this car unless its for the luls