07376369067 www.williamsmo... Support the Channel and Donate: www.paypal.com...
Пікірлер: 160
@yueru33 Жыл бұрын
Thank you Kevin! I watched this about 1000 times and I've just finished changing the clutch on my Yaris MK2 1.0 It took me a lot longer than I thought but I did it.
@yueru33 Жыл бұрын
@@baracuda40 It took me several days because I struggled with a few bits but altogether probably 15-20 hours.
@didge110 Жыл бұрын
I'm doing exactly the same right now but I feel like its taking me longer - I keep referring to various videos. The biggest pain for me was getting all the ancilliary items off with bolts at the rear of the motor where I couldn't see them and reaching them was almost impossible and then the problem of how ro suppoer the motor and gbox whilst separating them@@yueru33
@fizaraja22055 жыл бұрын
Hello Kevin. I would like to thank you for guiding me through all the process and i have successfully changed my 2002 Toyota Yaris clutch kit. Which is quite similar engine. Hats off 👍
@WMCS5 жыл бұрын
Babar Gull Thanks for the feedback.
@WMCS5 жыл бұрын
Babar Gull Glad you got it done mate.
@fizaraja22055 жыл бұрын
Your’e Welcome bro 👌
@soldiersvejk20534 жыл бұрын
Glad to see someone succeeded! Also want to have a try. Just a quick question: did you leave the outer drive shaft in the wheel, or did you just left it in there and bent the brake over? I saw a lot of other videos removing the drive shaft completely, yet the staked wheel nut makes it hard to remove, and needs to be replaced with a new one afterwards. Thanks!
@rbutler29302 жыл бұрын
Perfect job Kevin, welldone! What a legendary step-by-step video, Make sure to add "Yaris 1.3" to the title it was identical. I must have watched this video 3 times over months to get everything ready!! ¬.¬ Took me around 4 hours, my biggest takeaway from the video was hunting down your mid-torque impact I ended up buying the gen 2 MILWAUKEE M18FMTIW2F12 what a game changer thanks!!! I needed to use a splitter for ball joints, hammered the **** out of them would not let go! Sending £20 on its way to paypal Kevin, thanks again!!!!!! Here is a quick write up i made you can take to the car with you, from the vid and with extras and torque settings from Toyota service manual Mark a piece of card for bell housing bolts to place in when removed 9 in total + starter motor bolt Jack up car high to get 4 jacks under, (maybe lift one side to get jack deep under onto mount bolt) Remove front wheels, chuck under for safety Drain gearbox oil, do up drain plug! Passenger side: Remove tray side guard (2 bolts 10mm) You may need to remove plastic under tray from front i did, about 8x 10mm screws Undo bottom wheel ball joint (ball joint splitter or Hammer) (Castle nut + clip) 98Nm* (when putting back if you cant get whole to line up tighten a little more) Undo lower link arm nut, disconnect (grips or Allen key) 74Nm* Drift out the driveshaft from gearbox with hammer & chisel Pull out and stow out the way Remove 2 bolts from bell housing at the front and next to clutch slave cylinder (wrench) Drivers side: Undo bottom wheel ball joint, Hammer & leaver or splitter (Castle nut + clip) 98Nm* (when putting back if you cant get whole to line up tighten a little more) Drift out the driveshaft from gearbox with hammer & chisel leave to the side remove 2 bolts above driveshaft spanner or extension wrench! (for starter?) 17mm & 14mm remove 4 bolts at the bottom of bell housing Remove 2 bolts from engine mounted under the centre and pull out engine mount 120Nm* Using block of wood Jack up sump just to take weight (when removing upper engine mount later) Under bonnet: Remove Battery, 10mm. Remove Battery tray 3 bolts (wrench) + cable clips Remove upper engine mount 7 bolts + cable clips Disconnect earthing lead 14mm Disconnect the 2 gear linkages pins Disconnect electrical connector Disconnect Linkages bracket (the 2 lower bolts) and stow up out the way Disconnect the clutch slave cylinder 6 bolts and tie up out of the way Remove top front bell housing bolt wrench Remove LAST 2 top bell housing bolts (wrench) next to gear selector bracket (care: gearbox will drop) *Carefully* go under and lower gearbox to floor!!!! Twist forward to lower down and out remember its heavy 15kg or more (took some wiggling to get it free) Clutch & Gearbox: Remember how the clutch sits before removing (photo!) Using screwdriver to hold fly wheel in place Remove the 6 bolts half turn at a time evenly and remove the clutch (Important note which way round the clutch plate goes springs face gearbox) Clean the plate and wipe with clutch brake cleaner, Clean rag!!! Before removing bearing check its correct positioning!! Clean gearbox, remove bearing, lightly re-grease arm/shaft replace the bearing check movement, grease spines lightly!!! Check clutch is the same and fits on splines! Fit new clutch with alignment tool, small dab loctite (blue) and torque bolts (Important note which way round the clutch plate goes springs face gearbox) Check its centered even all around, do them up in criss-cross pattern half turn at a time to clamp down spring pressure evenly Refit gearbox by tipping it forward and rotating back in to place, twist wiggle shaft back into place using a couple of bolts to hold in place Refit torque everything back in reverse, and then REFILL GEARBOX OIL!!!!!! ################################### Tools Required ----------------------------- Chisel + Hammer Long pry bar Ball joint Splitter Oil pan + Oil + syringe + Rags + Card 1/4" Short Ratchet + 10mm Socket 1/2" Rachet 1/2" Torque Wrench Spanners (both fixed & rachet) 10, 12, 14, 17 (tube for leaverage) 24mm Oil Allen Key (for sway link) Impact wrench + Short extention + Long extension + Universal joint Impact Sockets 1/2 - 10, 12, 14, 17, 21 4 Axel stands Trolley Jacks Large + small (to get one side up to get large under) Piece of wood to protect sump Brake cleaner + clean rag Loctite (blue) Clutch Kit 3 piece (as your taking it all off worth replacing for new, Advice to buy a quality brand as your going to the trouble to do this, it wouldn't be the fist time ive heard a clutch redone 6 months later) Clutch Alignment tool String/wire/bungee Shadow board for bolts Phone to take pictures if need be Good luck!
@WMCS2 жыл бұрын
Thanks so much for a detailed write up. I genuinely appreciate the time and effort you have put into detailing the tools and materials needed. It will help a lot of other users of this channel. Kind regards. K-A. Williams.
@paulluce2557 Жыл бұрын
I came here to look for the 'how to' on the Yaris as I am abiut to do one. I was wondering about torque settings amongst other things and this write up has it all. I am confident I can do this now.
@Gunsgame19667 ай бұрын
Best tutorial on Yaris/echo I’ve seen on all of utube guys well done 👍🙏
@contactmiller2 жыл бұрын
Just finished the clutch on my 08 Yaris 1.5L gas. Almost exactly the same as this video. Original clutch at 210,000 miles, the rivets were starting to groove the pressure plate, but the flywheel was still good. (I dive like an old grandma). Shined up the flywheel with an orbital sander. The hardest part was getting the bell housing to let go of the dowel pins. I had to hammer and pry for an hour to get that off. Just as hard getting it to mate back on. Great video, thanks!!!
@WMCS2 жыл бұрын
Excellent 🍻🍻🍻🍻
@pierresankey47525 жыл бұрын
Less talk, more work.! Love it. 👌👍
@WMCS5 жыл бұрын
Pierre Sankey thanks for the feedback
@PHSPictures4 жыл бұрын
What an absolute soldier. You are the MAN!
@WMCS4 жыл бұрын
PHS Pictures thanks for the review man. really appreciate it.
@killermy925 жыл бұрын
Good video! Thought I would be able to change my clutch by myself, but don't belive I'll be able to do that now. Still interested to watch.
@WMCS5 жыл бұрын
killermy92 thanks for the feedback
@kentdixon57165 жыл бұрын
Hey Kevin, loved your video, like your no nonsense approach, helped me a lot on mine, thanks for posting.
@WMCS5 жыл бұрын
Kent Dixon thanks for the feedback.
@toddcott95105 жыл бұрын
No a job for the faint harted. The impact gun sure helps. Great video, many thanks.
@WMCS5 жыл бұрын
Andy Clockwise Thanks for the feedback
@vinegar0084 жыл бұрын
I notice so many similarities with the Toyota IQ 09. Except there were 2 things which makes the IQ clutch one hell of a job. 1. A giant sub frame is in the way. The sub-frame stretches from the radiator to firewall. So you have 2 options: Drop the sub-frame OR lose the engine's sides engine mount, force the engine to one side to make room. (I took the second option, which I regretted). 2. The Driveshaft on the right is so much different. That particular Driveshaft is a steel rod comes out of the gearbox which is then secured to the oil pan by a bearing holder, follow by an inner CV joint, a rod then outer CV joint. What you'll find is the rod (which has is own bearing) is seized into the bearing holder by rust, makes removing this Driveshaft virtually impossible.
@WMCS4 жыл бұрын
Vincent Ng absolutely correct. It’s the same with the Toyota Auris. I always leave that one drive shaft in. I’ve never managed to get one out. As for the subframe. I find the gearbox can just fit inside if it’s dropped down on one side a few inches. Burning question. Did you manage to get it done alright
@jeandiamfoumfou2549 Жыл бұрын
Merci pour la qualité de ton travail tu es et tu restera un maître en mécanique
@willdatsun Жыл бұрын
Not necessary to remove driveshafts from hubs, there's plenty of swing on that left strut to just put the shaft form the gearbox and just tie it up to the brake lines. You don't even need to touch the RH driveshaft, apart from levering it out of the gearbox. you can then just lift the gearbox away from the shaft when you remove it. Also it is quicker to take the single bolt from top engine mount rather than remove all the bolts on the inner wing bracket. One more tip, leave gearbox in gear when you are refitting as it helps the spline to go into the clutch plate.
@WMCS Жыл бұрын
.
@tesytesy95314 жыл бұрын
You are very good at your job
@fizaraja22055 жыл бұрын
Best video ever 👍👍👍👌👌👌
@tonyn98584 жыл бұрын
this is a brilliant video for any diy guy wanting to have a go. what i like about this video the guy shows you what it is like in the real world lifting the box out on to your chest and the hardest bit getting the box to line up and back in. its a young man's game lifting gearboxes back in on your own.i did the Micra 2 years ago and i found it hard work as I'm 60 now. if you are a young chap give it a go you will save yourself at least £ 450 garage fees great video my friend. Tony Leics
@paulluce2557 Жыл бұрын
I will be doing one of these soon. I use an engine crane to handle weight of the gearbox as i am no spring chicken either..
@giovanniabruzzese51673 жыл бұрын
Quick clean and fast job Kevin.
@TU-TOF4 жыл бұрын
very good job ! Clean speed and efficient !
@WMCS4 жыл бұрын
Tutof thanks for the feedback 🤩
@romiadam56974 жыл бұрын
Excellent video. I am going to replace the clutch on T Yarris1.0L 2006 too, so this video will be a guide for me.. The comment as e.g. subtitles would be great (what to be aware or where to take extra attention, or what to replace, what to clean,...etc...).
@WMCS4 жыл бұрын
romiadam it’s a fairly straight forward repair. If you follow the video it should be pretty much self explanatory. If you are not sure about anything you can always send us a message.
@ray012025 жыл бұрын
Y the 3 thumbs down he noes his stuff keep the videos coming 👍👍👍👍👍👍👍
@WMCS5 жыл бұрын
ray01202 Thanks ray.
@domenicaloisio51364 жыл бұрын
Thanks for the video, I will have to do mine soon. I like the floor mat.
@WMCS4 жыл бұрын
Paul Domalo they’re definitely good the floor mats. You can pick them up from Halfords for about £12. Otherwise on eBay
@davidm13543 жыл бұрын
Fantastico non ti stancare mai di pubblicare questi video🙂🙂
@PaulB584 жыл бұрын
Thank you very much did my clutch following your video step by step perfect keep up the good work
@WMCS4 жыл бұрын
P B glad the video came through for you. Thanks for the feedback.
@nikolayneshov61203 жыл бұрын
Hello, Recently, I bought Toyota Yaris 2007, 1.3 VVT-i, MT, Engine: 2SZFE, French build, LHD, 114 000 km. I've a problem with the clutch pedal biting point, which is fully down to the floor for all of the gears. Sometimes when I try to shift into Reverse (even if the clutch pedal is fully depressed) a grinding noise is heard when I move the gear shift. If I push the pedal fully down on the floor, shift into 1st gear and release the pedal even 1-2 mm higher than the floor, I can feel that the car starts moving. Sometimes when I drive and switch from 1-st to 2-nd gear, the shifting of the gear is a bit difficult (the pedal must be strongly pressed fully to the floor). My leg gets tired after a long drive and sometimes I cannot make such a presure, so the difficult shifting problem appears. The pedal free play is around 17-18 mm. The push road play is 7-8 mm. The pedal height from the floor seems to be OK (It's a bit higher than the brake pedal). I can depresss the pedal fully to the bottom on the floor. When relased, the pedall gets back to its highest position normally. The pedal is not soft. The clutch has never been replaced. Service technicians said that I need a new clutch. I asked them if bleeding is needed, but they said that the clutch fork mooving is quite well far, so the hydraulic system is OK, and bleeding can even worse the problem. Here is how the clutch fork looks like when the pedall is fully released and fully depresed: drive.google.com/file/d/1Bd1y0MzWDXWIQeLhFrjiWu2JNkG9-veH/view I was wondering if the pedall free play rod can be adjusted, but I can't seen any adjustments on my master cylinder. Please see the left part of the figure bellow: drive.google.com/file/d/1wzsue-fkHt-FGJeaFHPUFynZFSDBeAdH/view Can you give me an advice?
@talat034 жыл бұрын
Tu connais tout les voiture bravo 👍👍👍👍
@WMCS4 жыл бұрын
talatos03 un bon Peut de voiture... normalement je travaile tous les voitures.... Joyeux noel pour vous a la famille..et bonne heureuse anne 2020....🌟✨
@binagarten46673 жыл бұрын
Damn this is a superb watch!
@WMCS3 жыл бұрын
🍻🍻🍿✨✨
@stefstefoflex17934 жыл бұрын
Gros job👍 Thank you, from France
@chouchou457 Жыл бұрын
Merci pour la vidéo.
@WMCS Жыл бұрын
You’re welcome
@escanored59582 жыл бұрын
Oh noo you forgot the oil 😅 Nice video👍
@user-hd5dq4zi2h5 жыл бұрын
Thank you!!!
@JordanPeterson. Жыл бұрын
realest nega out there. i hope your doing good my g and staying strong
@3ziz9615 Жыл бұрын
Thanks for the video.
@tedbear2441 Жыл бұрын
Brilliant video. Just one question. Did I miss you refilling the gearbox oil?
@yueru33 Жыл бұрын
It's 1.7 litres of 75w. Fill it until it comes out of the fill plug.
@soldiersvejk20534 жыл бұрын
Very good video! Does this work on 2009 Yaris 1.5L? Also, how high do you need to jack up the car? Do you need to support the engine with a bar?
@WMCS4 жыл бұрын
Jiateng Wang just enough so you can get underneath. I use the jack to support the engine.
@soldiersvejk20534 жыл бұрын
@@WMCS Thank you! I watched another video and he is taking a lot more parts off than you do. So I just wonder if your method only fits 1.0L model. I don't think they have that model in the US.
@WMCS4 жыл бұрын
Jiateng Wang I’ll do a video of a 1.5l engine. Bound to get one sooner or later.
@soldiersvejk20534 жыл бұрын
Kevin-Albert Williams looking forward to it
@dermann24215 жыл бұрын
Great Video. Obviously know your way round the car!! Bet You could do it with your eyes closed ?!!! Given me some confidence.
@WMCS5 жыл бұрын
Ryvan MORRIS thanks it’s not so bad when you are actually doing it.
@rodrigosepulveda92053 жыл бұрын
Arto esfuerzo felicitaciones......Saludos..
@alfrediwanek55072 жыл бұрын
Great ,Master ! Worker .Thank you for this viedo !
@JLima-cz6kd3 жыл бұрын
Excellent, thanks for posting.
@markclan63314 жыл бұрын
Das ist wirklich klasse. Wow
@kennethvenegas81874 жыл бұрын
Its a verry hard this work i did happines 👍👍👌👌
@WMCS4 жыл бұрын
Kenneth Venegas it’s too bad as long as the weather holds up nicely... some cars are a bit more tricky than others tho.
@islamzaytsev75713 ай бұрын
Thank you 🙏
@darkokure4 жыл бұрын
Kevin,merci pour ton partage
@bigmacou2 жыл бұрын
Thanks!
@martinm342211 ай бұрын
thanks for showing...that i'm not able and willing to do it.
@brianrozgodfrey28305 жыл бұрын
Job well done
@WMCS5 жыл бұрын
Brian Godfrey Thanks for the feedback
@011235813213413 жыл бұрын
Hi - how similar is this engine/gearbox and procedure to the 1.33 L Yaris ? I have a 2011 Yaris with the 1.33L 6 speed engine and need to replace the clutch...
@WMCS3 жыл бұрын
It’s almost the same except for the driveshaft. Some of them runs in the front. Have a look on the channel for the Toyota IQ
@MultifunctionKaTech4 жыл бұрын
Thanks for the video. Very good
@WMCS4 жыл бұрын
Multifunction KÁ Tech appreciate your review and for taking time to visit our channel
@thewolf5651 Жыл бұрын
Exelente tutorial.....
@toyotoe37324 жыл бұрын
Thank you
@WMCS4 жыл бұрын
toyo toe thanks for visiting the channel
@hassemsadiq4 жыл бұрын
Would love to see a Toyota Corolla verso clutch replacement
@WMCS4 жыл бұрын
Infinity vidz help the helpless I’ll bear that in mind as soon as I get a booking for one I’ll make a video.
@ceckoslav3 жыл бұрын
Good job! What time did it take you to do it on the street?
@mazambeliqbal34872 жыл бұрын
I got 2006 Toyota Yaris 1.0, mine reverse gear wasn't able go in popley and need to change the gearbox, done mine at home , plus it not easy when working on the floor . at the end I done my job and vehicle back on the road again 😏😏
@WMCS2 жыл бұрын
Excellent 👌🏼
@leonardoflorez12133 жыл бұрын
Very good job...
@mannib68143 жыл бұрын
Greetings from Germany, great videos. Have a question, is the Aisin clutch good?
@WMCS3 жыл бұрын
Yes it’s very good for Japanese cars.
@shakib12502 жыл бұрын
Thanks
@WMCS2 жыл бұрын
You’re welcome
@kennethvenegas81874 жыл бұрын
Good good 👍👍👍🇨🇷🇨🇷🇨🇷 garage fix mechanic
@WMCS4 жыл бұрын
Kenneth Venegas thank you mate. What’s you glad please ..
@teddyjan1839 Жыл бұрын
👍👍👍🙂
@marcor.27374 жыл бұрын
Hello Kevin, very good guide. Do you think diesel version for the same car is quite easy as well?
@WMCS4 жыл бұрын
Marco R. It’s more compact but overall roughly the same.
@marcor.27374 жыл бұрын
@@WMCS do you mean diesel version has less space to manouver?
@WMCS4 жыл бұрын
Marco R. That’s correct... I haven’t seen a 1.0l diesel yet. But I have worked on the 1.2L version and they are a bit more compact
@jusb10664 жыл бұрын
@@WMCS there is no 1.0 diesel, it was a 1.4 , the 1.0 and 1.2 are petrol
@tiresombeast6772 жыл бұрын
What oil did you top the gearbox up with?
@tamrat_assefa4 жыл бұрын
So... I have the same car and it makes a slight rubbing sound when ever I disengage the clutch (depress the pedal). It seems like its louder in the morning but its there through out the day. Not sure what's the cause. Job seems like something I can do at home with the help of a friend. My question is, would I need any special tools when replacing the clutch (I read somewhere that I need a clutch alignment tool, don't know if that is really necessary) or if I need special tools to replace any of the bearings?
@WMCS4 жыл бұрын
Tamrat Assefa if you look in my channel. I’ve recently started showing how to align a clutch. It’s a simple £5 clutch alignment tool .. you’ll definitely require it. The noise sounds to me like the thrust bearing. It’s easily replace as shown in the video. On the flip side of this. Is your vehicle a petrol or diesel. ..? Thanks
@tamrat_assefa4 жыл бұрын
@@WMCS Thank you for the reply. Mine is a petrol (the 1.0L 1KR-FE). I'll definitely watch your videos on how to align the clutch. Thanks!
@WMCS4 жыл бұрын
Tamrat Assefa no probs... the 1.0L is fairly straight forward ....
@xinixxagnix2014 жыл бұрын
wtf need a torque wrench lol trained hands feel the torque with +- 5 nm off xD, Great job m8!
@stephendixon36964 жыл бұрын
Do you know how you would adjust a clutch on a Toyota yaris 2013 the bite is a bit high ?
@011235813213413 жыл бұрын
don’t quote me but i don’t think it is adjustable. Almost all modern car’s clutches are not adjustable, not like the old days were you could....
@011235813213413 жыл бұрын
if the clutch has a high bite point i’m fear you’re in the same boat as me and the clutch is coming to the end of it’s life 👎
@stephendixon36963 жыл бұрын
@@01123581321341 its not too bad I Fort at the time it was high as I wasn't used to the car But a year later it's going well. I have a Citroen C1 and I know I could adjust the clutch at the time and was thinking if I could on this vehicle . I'm a toyota yaris 2013 1.3lr
@011235813213413 жыл бұрын
@@stephendixon3696 i would love if i could just adjust my clutch - a 2011 Yaris 1.33 6 speed. It needs replacing and i was worried it would be a pig of a job but after this video it doesn’t seem so bad
@jackjonson26964 жыл бұрын
Hello mate do i need to remove the gearbox to remove the engine on toyota yaris t sport ?
@WMCS4 жыл бұрын
Jack Jonson no. You can drop the whole thing down if you have a ramp. Or twist it round and pull it out sideways if you’re doing it in the floor using a crane.
@jackjonson26964 жыл бұрын
@@WMCS i dont have a crane, so could i remove the engine in bit by bit ? Without removing the gearbox an clutch ? Thanks
@WMCS4 жыл бұрын
Jack Jonson you could probably do it. But keep in mind you have about 10 inches to pull out the spline from the clutch and flywheel which may make it tricky due to how compact the engine is in the bay.
@gordonsmit33962 жыл бұрын
Hi Kevin.. Will a GWM Florid 1.5 clutch replacement more or less be the same..... Apparently is the parts the same.. 🤷♂️
@WMCS2 жыл бұрын
Gordon I had a customer emailed me with a similar car. Apparently the clutch spline is different. But the pressure plate and the rest is the same. So I won’t work.
@Carlostype3 жыл бұрын
Hi, My 03 Yaris won't select gear intermittently. I notice the slave is not leaking and seems to operate the fork. Last time it happened I noticed I could select 1st after turning engine off but I feel a slight pull when I dip the clutch. Can you advise me as to what could be the problem? Thanks
@WMCS3 жыл бұрын
Most likely the pressure plate.
@Carlostype3 жыл бұрын
@@WMCS That you for your reply 👍👍
@clipper651 Жыл бұрын
top !
@af2523 жыл бұрын
How long did this take in total? I assume it’s slightly longer than the video since there were cuts.
@WMCS3 жыл бұрын
About 2.5 hrs roughly.
@af2523 жыл бұрын
@Kevin-Albert Williams how much did you charge for that roughly?
@Ramallinone Жыл бұрын
@Kevin-Albert Williams Does 1.33 petrol 2009 is harder? I have start stop and is slightly slipping on cold mornings. I noticed that release bearings is slightly different with triangle shaped patern to secure in to gearbox. I will choose valeo or blue print clutch. Can I buy valeo clutch with luk release bearing or its dosent matter which brand is release bearing? Prices is not that cheap considering the car. I done 4 clutches already and I need to prepare for any surprises will do this car to me. Thanks
@fsul85362 жыл бұрын
Hi, I have a 2011 Yaris 6 speed manual it wouldn't go into 4th gear when driving I can't figure out if it's the clutch or gearbox if anyone knows much appreciated. Thanks ☺️👍
@richardjones8684 Жыл бұрын
Hi Kevin would you know if it’s exactly the same for a 2009 toyota urban cruiser 1.3 petrol? Thanks
@WMCS Жыл бұрын
I wouldn’t know for sure to be honest.
@nirmalantony459 Жыл бұрын
Hello guys can anyone suggest me which clutch disc brand will be better for Toyota auris 1.33 , 2012 petrol.
@willdatsun Жыл бұрын
Anyone know which brand of clutch gives the lightest pedal feel?
@luisdavila80833 жыл бұрын
Y que paso con el aceite 🙉
@noussberad5 жыл бұрын
hi, can you please clarify why did you remove the two drive shaft rather then just one
@dragonskunkstudio75824 жыл бұрын
It is necessary as you can see putting in the transaxle back in the engine drive shaft is tricky as it is already without also needed to align the other drive shaft at the same time.
@tiresombeast6772 жыл бұрын
Do i need to bleed the clutch if I replace the slave cylinder which comes part of the kit on a semi auto. Also how do i go about bleeding the clutch as there is no clutch pedal with the semi automatic. Any help would be appreciated.
@WMCS2 жыл бұрын
You have to sequence it. .. usually with a software
@tiresombeast6772 жыл бұрын
@@WMCS what do you mean by sequence it?
@antonio-ww2zt8 ай бұрын
Ciao doctor Kevin quanto tempo impieghi per sostituire la frizione Yaris 1000 del? 2007
@WMCS8 ай бұрын
Dr 😁🍻… for me personal about 2hrs. But allow yourself another 2
@antonio-ww2zt8 ай бұрын
Grande veramente sei molto bravo 👌👌
@786subhaankhan3 жыл бұрын
Hello Kevin are u in the UK. We're are u located cheers
@castrolgtx50644 жыл бұрын
One of the easiest clutches I’ve ever done pity they’re not all like that.
@kokagt59943 жыл бұрын
No me acuerdo donde va tanto tornillo
@willdatsun Жыл бұрын
did you put oil in it?!
@martinm342211 ай бұрын
what a pain without a lift and no support arm.
@chinkonojutsu9 ай бұрын
This require a lot of mecanic skills I am not feeling able to change my clutch kit
@NickAbbot. Жыл бұрын
I saw another video where they remove the steering knuckle from the strut instead of the ball joint like you did. You’re way seems a lot easier, you don’t have to remove the entire shaft.
@WMCS Жыл бұрын
That’s it.
@jackjonson26964 жыл бұрын
Isn't this gearbox replacement not clutch ?
@WMCS4 жыл бұрын
Jack Jonson it’s to guide you to the treasure and out again. I suppose I did this to help mechanic who already knows how to bolt and unbolt a clutch ...
@jackjonson26964 жыл бұрын
@@WMCS ok thanks mate just i was asking because iv only just trying to familirise with these parts of car
@karoma78984 жыл бұрын
how is there so little in this car yet it's so hard to maintain! i needed to change a light bulb the other day and needed to take apart it's entire front plastics... wtf toyota?
@WMCS4 жыл бұрын
kar oma 😁😆.... it’s getting expensive to change just a light bulb nowadays.
@verygood71555 жыл бұрын
This is disappointing. Your video does not guide us through the actual process of replacing the clutch itself but only how to access it.
@soldiersvejk20534 жыл бұрын
Very Good Replacing cluthes are simple and universal,while Removing the transmission is different from car to car.
@lawts12404 ай бұрын
Nope, this video is exactly what I needed! Plenty of other vlogs on clutch plate fitting out there so many thanks. Perfect. (Just wish you would stop all the chat and get on with the job! 😁) BTW, How do I find one of those balaclava mask thingies??