73168-SNA-013 73158-SNA-013

Nice video, I was able to follow the steps to replace both the left and right Drip Edge Molding parts. Here the parts were about $115 each from the Honda dealer, and the clips were about $3 to $5 depending on the type. The box that each molding comes in is 8 feet long, about 18 inches wide and 4 inches deep, about the size of a surf board. By folding down the rear seats and moving the passenger seat all the way forward and reclining it I was able to take one box home in my Civic per trip from the dealer. The yellow and blue clips, underneath the floppy rubber bit, can be more easily removed by using a small flat head screwdriver to release the tab through the slots on the white clips that are attached to the body. The clips are fragile, so be careful. The section that runs along the roof can be most easily removed by tilting the drip edge molding towards the center of the roof. Again, remove the parts slowly and carefully to avoid breakage. My advise, pick up some extra yellow clips. Depending amount of deterioration you may find that some of the clips are damaged, also they break fairly easily. I also discovered that one on the white clips along the windshield had only half the plastic remaining and I had to run over to the dealer to pick up a new one before proceeding. The entire process took about 35 to 45 minutes per side. It was fairly easy to do. I can't believe that Honda wanted about $200 in labor for each side to do this relatively easy fix. Thanks for the video, great job!

Excellent Video. I followed these simple steps and completed the job in about 40 mins. (I could do it in half the time if I had to do it again). Parts were $92 each at my local Honda dealer. Called first to make sure they were in stock. Part numbers for 2008 4 Door Civic were: 73158-SNA-013 and 73168-SNA- 013. Left and Right.

Should definitely be a recall for these all my molding is gone also.

Thank you for taking the time to help us all out. You would make a great neighbor 😁

Thanks for the video!! Here’s another PRO-tip when removing the old molding! 👉 you can avoid breaking a clip by pushing on the yellow tab you can see through the window of the white clip, as you pull it upwards.. I used my pocket knife to press the yellow clip in a bit, which helped me get it out smoothly... I learned this after breaking one of the white clips on the first side

Thank you so much! Love the video! The dealing in San Diego wanted to charge me $106.12 parts, per side, plus $120 per side installation. Dealers are Robbers for sure!

Thank You for the awesome video and giving me the part numbers i needed. I could not tell what was needed by the diagrams I looked at. Call Honda and the had the right side in stock, 150 bucks in California. Returned home and installed in less than 15 mins. Once again Thank You...

This is why the internet is awesome. Thank you for posting with part numbers!!!

Migs714, I really appreciate you taking the extra effort to record the awesome and succinct tutorial - good looking-out, wingman. I've got a 2011 Civic; parts look the same; now searching for parts.

Dealer wanted $450 for parts, labor, and install. rip-off! Awesome vid, thank you!

I just replaced mine without any issues. Thanks a lot for the detailed instructions. As a hint, rather than pulling the old trim directly from hand, just use a flat-head screwdriver to gently push the clip fastners. This way you can ensure all clips are secured for reuse in the new trim.

Mine are missing as well on my 2010 Civic ! I feel it should have been a recall for all 2010 Honda Civic for this issue !

Thank you for sharing this. It is exactly what I needed to know. The car wash blew out both sides on my 2010!

Just replaced the same trim on my 2011 Civic, thanks for your time and effort sir to post this video. God bless!

Thank you so much for this helpful video! Saved a lot of money doing it at home instead of through the dealer. Thanks!

Thank you for making this video so clearly and not over explained. Keep doing more videos 👍🏽

Thank you for putting this video together. It put my mind at easy to know how the thing was held together. I just replaced my left and right molding for the cost of the parts, which wasn't cheap. This part was so poorly designed. Honda should have realized how stupid the design was when they had to put the part in 7 foot long boxes. Thanks again.

I'm adding another "thumbs up" for the OP's creation of this video. Like others, I needed to replace one (driver's) and the other was showing serious signs of deterioration as well. (vehicle is 10 years old, though.) The dealer's price for labor/installation was insane. Labor at home took about 40 minutes, and saved about 200 bucks. Note: For those considering a do-it-yourself option.. the installation isn't bad. However, where you order the parts from will make a difference. True, dealership pricing isn't cheap. However, if you order online, note that not only are you paying shipping, the cost will be far more than usual as the parts come in boxes that are about 7 feet in length. Therefore, (as I understand it) they can't be shipped through regular protocols are are considered "Freight", adding even more to the shipping costs. Go ahead and buy the parts at the dealer. Handle the installation on your own. Oh.. go ahead and purchase at least replacement yellow clips. The ones in place may have deteriorated and could break off when removing the older parts. It's far better to pay the extra and have the clips available, than to risk breaking one, and have to make a second trip for parts.

Very good instructions…Thanks

@migs - Extremely appreciative of this walkthrough! Replacing these on my '07. The black covering on the moulding had started to separate along with the little skirt between the moulding and the windshield.

Thank you for the video. I didn't know what to call that trimming. Regardless of word play you'd think it would still pop up when I searched for it. Wrong. You're much appreciated!

Thanks for the video. Extremely helpful. After reading the comments I agree, Honda charges way too much for the aesthetic parts.

Thank you the best video I’ve seen so far, to fix this problem

Thanks for the video. Got the parts from eBay ($200) and did in one hour while following your video.

I know you put the part numbers up in the video but it would be helpful if you put the part numbers in the description and where you saw them online for $65.

1:57 looks like Big Bronson Reed in the window lol

Excellent!!!! That trim is Now $123 at the local Honda dealer and Online $71 but they want to gouge you for $200 Shipping!!! Thanks, that's simple!!!

Thanks for the video, great job!

I haven't replaced mine yet but I just got done doing a road trip and the clips are exposed because the rubber flew off. The wind noise was a lot louder so it helps in that area too..., so I need to fix it asap! ***Edit- Replaced the parts. Thank you for the video.

I really appreciate you doing this video. I couldn't find much info on how to get new ones. Going to order these for my Civic ASAP. Thanks yo!

Thank you for making this. Helped me switch these out in 30 minutes!

Thanks for the video greatly appreciated. Now I need to call the Honda dealership and have them ship me the drip edge moldings.

Thanks guys. That was helpful to see it done. I’ll be doing mine this weekend.

Love the track in the background!

Mine are gone as well, should’ve been a recall.

If you are going to replace this yourself you need to know that simply pulling the trim to unclip doesn't work. You want to use a flathead screwdriver to press the part of the clips that are holding onto the part that's connected to the car. This allows you to remove the trim and reuse the clips. I just replaced mine and broke three clips in the process.

Just replaced mine right now and this video was very helpful since I should’ve done it 5 years ago.😂

Thanks for sharing now my car won’t sound like m Going back to the future when I hit 88mphs

Very helpful video! I just bought a 2010 8th gen myself and really need to do this for my car. Can someone please send a link to where I can order these drip moldings online? Thank you!

This video is a big help!! Thanks bro.

Thanks the part numbers were super helpful

Well done, thanks!

Any alternative fix for a low budget college student? Parts where I live won’t go for less than $150

Thank you! My Honda's trim is basically gone now and I need to replace it.

What about the rubber seals that go in the sides under the trim?

What will happen if I don't fix this on my car?

Honda Civic 2016, top molding is coming apart, wondering if I can change that part without disassembling the windshield

Thank you

I have the same problem is 2009 honda civic could you tell me what is its name of the parts that you replaced

Can't believe Honda Service Department charges $200 to install these moldings. Insane! On a side note the shipping costs are more than the actual moldings. So I guess I will have to buy at the dealer. Unless anyone knows where these can be bought and shipped at a fair price.

How much is the cost of rubber sir

I still my 2008 honda civic which runs great. I installed these about 2 years ago. All the civics I see on the street do not have these. The pieces are difficult to find because of the size. I found mine in amazon but you cant find then all the time.

Hell yea!! Nice video cause I’ve been wanting to replace mine. THANK YOU!!

Thank you for the video really helped out a lot. Been meaning to do this project for a few years now and wasnt sure how to. Thanks!

Thank you for that excellent video on the install !

This helped a lot. Thanks for sharing

Great video, glad I found this. I also have a 2010 Civic and need to replace the same thing, including the window trim on all 4 doors. My local dealer here in Newport News, VA quoted me $1,463.00 for parts and labor for the 4 windows and the windshield trim......yes that's correct, $1,463.00. Parts was about $500 and the rest in labor. Of course I declined.

Thank you for the part numbers.

Do they come with clips or you have to purchase the clips separately? Thanks!

thank you, just did a 2008 and it was easy, thanks to YOU

I have been looking for these steps and part number for a long time. Thanks a lot for sharing. Just a query, does this come as one piece with the rubber seal and side plastic cover that closes the gap between the Windshield and the trim?

This is the stupidest design ever.thank you very much for the video.saved me a lot of money.stealerships are outrageous with there prices.

Where can i order the molding trim from? I can’t find it. That’s how it look on my 2007 Honda Civic LX sedan

Where did you get these parts? Everywhere I'm looking is $200+ for both.

exactly what I needed thank you!

My honda Civic the same problem both side I need buy the same that or just the rubber strip I need to buy to protect the rain

Thanks! Question if anyone sees this: When I search the parts, 73168 says L drip guard, and 58 says R. Does that mean left and right? In the video and in comments below, it seems that is opposite. Is the side based on looking at the windshield or sitting in the car? Thanks!

Perfect video. Part is hard to identify. White clips exposed on my car as well cause rubber is gone.

Awesome thanks for the video , i was wondering what it was called

Thanks for the post! the rubber stripping was blown away in a carwash on both sides of the windshield. If I buy these mouldings will they come with that rubber weather stripping/seal/ attached? Thank you for reading this and for your response. If the seals dont come with this moulding, would you know of how I could get the seals and repair the car? I noticed in your video the rubber seals are missing before you put on the mouldings and then the seals are there when you put the mouldings back on.

Will water get inside if dont replace? Can i put some tape instead lol.

Will this parts fit a 2011 Civic LX 4 doors?

Can you put a link to where you got them??

Exactly what i needed. Thanks.

Migs174 Thank you so much for this Awesome video! It helped me gain confidence for diy and I just got it done! Honda dealer quoted me $493 for parts and extra for labor. I bought my parts online for both left and right trim molding for 225 delivery inclusive and used the existing clips. Honda Civic looks pretty now😁 I broke one clip but the molding seems to be in place.

so i dont need the long strip that goes along the roof of the car. i just need the piece covering those yellow clips on the sides. what is the model # for those? or the name

awesome video. just what I needed.

Can you share link where you got these moldings from

Honda should fire the person designing the trim around the windshield. The one around the CRV windshield was also a pain.

Question, what it the rubber lining part you installed in the inner part by the front windshield after you installed the drip side part

Hello Where can I find those products?? Thanks

Where did you order it from??

Do the lower corner plastic cowlings on the bottom corners of the windshield have to be removed in order to remove or install the bottom end of these moldings underneath the cowlings??

I put the trim on and new clips. Now the clips rattle at highway speed. I've tried everything and nothing stops it. Any suggestions?

Why does the molding come out so easily when windy? Any fix for that? Thank you so much for your video. Annoying music though. Good teacher/demonstrator

Online links for parts?? Can't find them online for under $150

Thx for posting the part # the video also helped with removal/installation

This video is so great that I wish you could hear WTF they’re saying

Does roof molding on Honda Civics help to keep water out of windshield and surrounding area?

Honda don’t sell the parts anymore. What is another alternative?

Great install video!👌👍

Thank you for posting!

Music source? Ty for the vid!

Mines missing just on the sides of the windshield can I buy just that

Great video. Would you provide the links on where to buy the parts. Thanks.

Hello Migs. Thank you for posting the video. Is this necessary to replace or for cosmetic purpose only? My trim's rubber are peeling.

Where did you purchase the trim from, it's hard to find.

Hey my Honda need that part what is it called so I can look it up

Hey what are those hole looking things by the windshield I need one like the are big circles by the windshield wipers