Did my first clutch today on my mams Peugeot 207 1.4 Petrol... this is the only video I needed to refer to. Took me 10 hours but with the LUK kit costing €70, €20 for oil and €5 for a large tin of brake clean I got away with the job done for less than €100. Most difficult parts for me were getting at the starter motor bolts deep down the back of the engine and also getting that plastic bracket (3 bolts) off that holds the gear linkages, no space to work and VERY awkward. Flywheel was in great shape (no hotspots, heat marks or grooves) as was the pressure plate, release bearing, clutch fork and the gearbox input shaft (zero play, rock solid 😁). Replaced all the parts obv but whoever had the car before must have rode the clutch when driving cause it was only the clutch friction plate that was worn and it was down to the bones... car had only just started occasionally slipping but I'm glad I got this done today. Liked that I didn't have to drop the subframe and could just rest the gearbox on it while I worked on the bellhousing & flywheel fitting the parts. The gearbox weighed more than I thought as well but luckily it didn't take long to get it lined up and back on. Kevin doesn't actually show fitting the clutch plate & pressure plate or the release bearing and greasing up the clutch fork & gearbox input shaft but all easy. The one thing I did do was buy a cheap flywheel locking tool on Amazon which I used to lock the flywheel with a bellhousing bolt before I fitted the pressure plate bolts and also a universal alignment tool (LUK kit doesn't come with one in the box), again cheap on Amazon. Job was a 100% success and in summary it's a job any competent car diy'er could manage I feel. Thanks a million Kevin for a fantastic video mate 👍

So this guy replaces a clutch on the floor in the rain with limited space and no padding on the floor with no help and he get it into a short video. Massive props to this guy I'll be doing this on the 2posts at work forget doing it on the floor

Replacing the clutch on the Peugeot 207 1.6 VTI model right now. pretty much the same. Just sucks that the gearbox removal isn't that easy, but after watching this video, it seems pretty good to just lean it away enough so you can get to the clutch and the throwout bearing. Great job dude, keep going!

سوف يؤتى يوم ونلتقي واشكرك شخصيا على كل المعلومات والخبرة والسرعة والمهارة وخاصة وضع الكامرات كان مناسب لحساب كل الأبعاد، حقا تستحق الإعجاب ، لا يوجد كلام بل العمل في الميدان، من كل شخص اخد حكمة او فكرة او تجربة، شكرا جزيلا على كل الفيديوهات.... انها حقا ممتيعة وفيها كل المعلومات الخاصة بالميدان..

You make it look like I can do it in lunch time. Thanks for the video. Will be doing my 207's soon. But being from South Africa I dont work on a car if it even looks like rain.

Great video, dont know how you remember where everything goes. My 207`s clutch has started slipping when i go up a steep hill in fourth.

Felicitaciones! With rain Working 💪🇦🇷

The amount of times I've worked in rain/snow.... Great video...

You make separating the the lower arm/balljoint from the hub look easy! I'm doing this job at the moment and finding it a real pain

Greetings from Greece my friend...you remind myself...I have many clutches on the floor

Need to do mine soon, will be referring back to this a couple times

In these conditions hardcore...bravo

Thankyou so much for this video mate!!!!!

Nice work 👍🏼

great video, got one of these to do wednesday, i've got 205, C2, 206 but not a 207, pretty much the same but a few more bits to remove.. thanks for the video..

Thank you Albert. Türkiye den selamlar.

Hola maestro que torque de apriete lleva la placa de embrague y el volante motor?

Thank you for the video ! Do you need any special tool to carry out the replacement ? how do you keep the clutch disc in position when you replace it? thanks!

Best youtube vedo ive seen yet, going too give it a go myself,, thanks ;)

With the rain is not easy....good job

fantastycznie gratuluje wytrwałości

Felicitări BOSS👏👏👏

Did a peugeot deisel 207 fun the bolt at front above slave cylinder were it only turns 1/4 of a inch then backs on to the DPF braket there was fun getting it out all done running the 6mm Alan keys bolts for the starter fun aswell cheers very good job .BMW tommow .

Is there any adjustment required for the clutch while swapping to new one or the hydraulic line adjusts itself? I will be doing it together with a subframe swap so would you do it same way? Firstly put it up then same process as you did but before unloading the gearbox from the frame i would take off exhaust connector then few screws for the frame, drop links after what swap it and screw it back, all rest then do as you did. I am asking because i may be missed something in the subframe swap process that would be required or there is something to do with it as you mentioned it is better when it is off on one side but if it is totally off then gear box would not be supported by top frame mounts. Is that all the subframe drop would be for? Is there steering rack connected to the frame? I doubt it is not so i have to reconnect that too probably and would that be all? Any advice?

💪💪💪💪💪💪bravo Kévin

I have the same car, the same workspace, but better weather. Thanks for a great tutorial! :)

Your videos helps a lot mate Big thanks

Hi my friend has just changed his clutch but when he sticks his car in gear you can turn the wheels but the engine stays still what could it be

Hi, i have a peugeot 207 active and am trying to remove the clutch pedal but can't seem to get enough clearance to remove the Bush to remove the clutch and brake pedal, any tips?

Hello, nice job you do ! I also have a 207 1.4i and the typical steering rack motor failed. I wander if is hard to to change it myself (whole steering rack). I'm not a mechanic however I like this job and have the tools is just that I'm a bit scared because of the things I need to dismantle also the exhaust is in the way.

Needed this video, Nice job!

Are these clutches Self adjusting? Ive fitted on one a 2009 207, TU3A. Bite point is very high still and being told its because i didnt use a self adjusting clutch tool? just used the conical plastic clutch alignment tool. any ideas? thanks Video was very useful when i did the clutch.

how much do you charge to do a clutch kit replacement on my 207 peugeot 1.4 petrol i'm in dagenham essex

Is it works on many cars I mean that can do this from the floor?

which brand of gloves do you use? the one's I have tear after a few mins Thanks in advance

merry Christmas eve one,,,this xmas its the flywheel seal,,,god why didnt i change it last year,,,merry xmas KEVIN THANKS ONCE AGAIN,, only starter moto bolts ,,,when the rain stops lol,,or im going to get wet ,,

How much did you charge for this job i have same car and my clutch went today funnily enough 😣

Would this be the same process for the diesel 1.4?

did you replace oil in Diff? is the fill plug under the battery tray ?

Hi. Can you tell what brand is the clutch set?

The undercarriage of this looks pretty clean. Where abouts are you in the UK? Down where I am, this car would’ve rusted through by now.

Salut combien de temps tu passe à faire un embrayage sur cette voiture et combien tu facture au client merci

Great video really helpful

Good wee video handy for ref

Thanks man, very useful. Doing this job on a 207 right now actually. But why drain the transmission oil? Just for the sake of it?

Great job on the video, really helpful! A small question I have is what was the oil you drained at the start after taking the wheel off? Thanks in advance!

me after xmas if the clutch holds out till then,,fk £400 to £500,, The last Peugeot I changed the clutch on was my 86 PUG 309 GTI,, miss that car,,

10/10

Amazing video again , any chance of a video with the 1.4 hdi on the 207?

great job , lovin' ya work!!! have a question you might be able to help with if possible. I have 2013 Peugeot 207 sw 1.6hdi which i'm going to attempt doing clutch on, and in the Haynes manual it says l have to drain cooling system and remove radiator assembly and exhaust system, it this necessary or just Haynes being over careful in case l damage those parts when removing gearbox?

Nice Job...👏👏

Like a boss

Do I need to remove subframe extension bar to change gearbox

Hi mate.... Do you have any tips on changing a slave cylinder on a 2.6 variant of this box? Many thanks

But you didn't show us how u changed the clutch tho. You just took it off and on.

Amazing

Hola heres un krass En esas condiciones en ke trabajas porke no usa una carpa para la lluvia

Thanks the amount of plastic on bemmers and you have no room to move the engine has to be lifted out harf way it's the deisel model 4 years old .merc, audi, rangerover, discovarys, all have there Owen problems BMW mini the most amount of bolts to come out .very good video put more on sorry to see you get wet and snow on the day you changed the clutch.

How do you make putting ball joints back on so easy 😂

lo encontre jaja, thanks you .

Hi! Good job. But, find some closed space, you will destroy your health

this is more a survival workout than best practise mechanics, you should wear a helmet, man 😀

and in the rain again ...

👍👍🇹🇷🇹🇷🇹🇷👍👍

Isnt it the worst car for clutch replacement ? ffs peugeot