Thank you Mario. Good job again. Have a blessed and safe week to you and your family.

You’re a beast Mario !! Love the videos. Keep them coming

Awesome diagnosis, thanks for sharing!

Thanks for sharing buddy. Good diagnostic

Appreciate you mate takeing the time

Nice job Mario. Thank you

Wow. You did it the right way. Evidence led you to the issue.

Yup, I run into this all the time here in Portland, Oregon. I use autohex 2 to read the ISN and transfer to a used good known DME and then code / program so the VIN transfers. New DME is spendy!

Good job Mario.

Love that scanner you got, good job on the diagnostic work!

You're amazing man.

Great job man, love your channel.!

Greetings from Ireland, new to the channel great vid as per all of your other vids I’ve watched so far, this car looks like it suffered from as we used to call it in my last job, it was suffering from German leaves.....! We used to service a shed load of 1 and 3 series and always clean out the drains of the leaves as they could cause rain water going where you don’t want it too....!

A small soda blaster nozzle can be very handy for cleaning corrosion off of connectors with relative ease. I use baking soda in one and it works great. Made by airboy who make air blow guns (for shop air blowing).

thank for sharing

Mario, you are AWESOME always good approach and logic to get the job done only if you took the time and showed ur viewer how did you finished the coding/programming the the DME and the tool u used and would be very helpful to the links where to get them as always good job and thank you for sharing ur knowledge brotha. cheeeeers from Ontario/Canada

Mario brother! Great video! Thanks for sharing! The cloning modules (if that’s the correct term) and all that is on a whole other level for me. Great stuff bro!

También es válido que nos toquen cosas "sencillas" Mario. Para no cansar demasiado el cerebro jeje Saludos Bro.!!!

Thanks your very good

Mario that is a mess an expensive one at that. Thanks for the advice and sharing. Stay safe and well 😊

Good job

Easy to take apart and clean. Most of the time it will work again.

You’re good bro, peace out

nice job

Nice !

Very common nice video

nice Mario

Awesome Diag👍 Bro what were the challenges with Autel, when writing the donor DME's ISN on the FRM & CAS modules Also, plz consider filming the process of programming donor unit's on bench, it will help many sub's worldwide😉 Stay Safe👍

I've come across a product it's good at dissolving rust and corrosion and it's still used in coffee makers believe it or not and soon a small bottle you can get at the grocery store but this stuff works better than anything that I've ever found on the market today and it's inexpensive, a little bit of that on a on an old toothbrush and you will not believe what ends up happening with your electronic connections almost like brand new, and then you blow it out with some compressed air in your finished

i wanted to see the power and ground and comm wires hooked up and check out communication...

My car also cranks, but doesn't start. Not fire...I have to check dme. I saw the video well.Thank you...^^

Is there a channel for the remapping part?

who is this scanner danner you speak of ? sounds like a cool guy

Mercedes turns the fan to full blast because there’s a separate device from the ECU for the thermal managing. In BMW, the DME does all this together.

Todavía estoy esperando los subtítulos en español 👍

I have a 97 528 I no Start No Crank. Any advice on where to look for the ECU Or ECM

This is why you should always clear your water drains, seals/covers, the trays, & if you have a sunroof.

literally had an a4 b6 2.0 na today with water damage in the pcm connector. caused coil control to be shorted to the injector control circuit because they are on the same connector, shitty design to begin with. coil controi is like 10% duty cycle while injector control is 80+. caused a burndown of couple of cyl3 coils because on time was so high. thorough pcm connector cleaning took care of the issue.

That sounds like replacing an entire wiring harness from the DMV? As I said previously you can use this corrosion cleaner in the connectors and on the DME itself and you will not believe just by using a toothbrush or a connector probe that's used for cleaning connectors how quickly this will clean that up in a matter of minutes versus spending hundreds of dollars on a DMV and a whole wiring harness? That unit is supposed to be covered with a weatherproof seal to begin with? What is the deal with that?

Please help me I have an e90 2011 328i I went through the water I turned off the car does not boil nor the glass cleaners do not work maybe you can help me what can be

12:19 something in the cabin air inlet moved

Mario quit zooming in. on your face lol . Great job .

Ayuda mi BMW x5 4.8 2009 no da marcha y al parecer creo que es porque la palanca de cambio no marca la velocidades nadamas se ilumina de rojo pero no marca la velocidad ya cheque fusibles y relay y todo bien cheque el arnes de la palanca y tiene corriente pero el de la transmisión no tiene corriente será por eso que no marca la palanca y no arranca? Espero y me puedan ayudar?

Hi bro ,, my car same porblm,, what can I doo now

What could 2ACC code mean for a 2008 328xi n51 e90

Mario we can see your tonsils. lol 😂. Good find. Stay safe

Did u figure out issue??

🙌🏼👍

Autologic for BMW is the must.

If they would just set the DME facing down with the connectors. its obvious that design would have problems. I bet every one of those with that design is going to have them same issue. I guess its their way of selling ecms and wiring harnesses forever. Do most bmw's have the ecm/dme in the same location and facing up like that? It will be the first place I check on anymore bmws.

How much would something like this cost bro?

Mario los subtítulos en español 🛠

What is your technique when cleaning corroded connectors like that ? Such as do you have a trustable spray you like to use ? Thank you for the content , really liking this channel .

Isn’t there a cream plastic weather cover supposed to be on top of that DME??

Wow talk about water intrusion! What about a gallon of DeOxit?

Are u in Phoenix

Did you look at the video at 12:22 for whatever reason the Recirculation door opens up🤔

I used to work with a guy who's teeth looked worse than those DME pins. Not kidding. That wasn't even the bad part-- it was the breath from the dying teeth. If CRC made tooth paste, I would have gotten him a can for Christmas. Thank you for another superb video! Was cool to hear the Diagnose Dan shout-out! He seems like a great guy. Maybe when tbe virus passes you can invite him to the Super Mario Miami Mega Mansion Magnificent pool party?

make sure you clean those drains before you put another one in.

It would have been interesting to see , if you would have just cleaned the female and the male terminals and then tried to start it up! I have a feeling it would have been fine. Why didn't you try that?

euro classics.fish bowls

Wait until they fly. Lol it's the worst mistake man ever did was put a computer in a car.

Thank you for a conclusion on your video and Diagnostics I was kind of confused why you kept trying to laugh all the way through dictating your video? That makes me feel that you're not serious about the work that you're doing?

Wow... that's extremely bad! Quick & dirty here. Lol

Nice handsome face, good job on this!

There's way too many reasons for no communication. I think your going to have BMW software

There are some sloppy mechanics out there! Forgetting to put stuff back. So irritating.

We've had loads of these. Really shit design from BMW putting their DDE/DME inside a washing up bowl.

Whereee are u because these mechanics are lazy

ok but all the wires going to that DME are also most likely corroded... since the water goes down that ground cable and makes its way into the wiring harness. the water vent below the DME box is also probably clogged..same problem will return after a few rains. this is a dishonest fix. typical bmw money grab by the mechanic just throwing parts at it. to actually solve this problem you would have to remove pins from connectors that are corroded and replace wires that are dirty. this is why I fix my car myself and don't bring it to any shops. they also steal parts out of cars like these! fix the car yourself or don't get a European vehicle.