There are 3 things to look at your brake light switch, the abs system( expecially the wires) and your front wheel bearings. I have a jacked 2010 4x4 and that those lights let me know my wheel bearings are about to go. I also had a abs wire get pinched and was grounding out up front. Hope that helps

I was having the same issue I replaced the spark plugs and wires problem solved thanks for the video

I'm starting to have this problem too! I'm checking KZfaq for a solution.

I know this is an old video. But if you have this problem check your codes. U0101 is a transmission control module failure. It’s $500-600 to replace and have flashed. Good news is that it’s covered under the Federal Emissions Act for 8 years or 80,000 miles. A lot of dealerships don’t even know this. Hope this helps someone out.

Guys, just disconnect the Negative Battery Cable, clean it with abrasive cloth, reconnect the cable Ensuring that it’s snug and tight, ( removal of the fender firewall brace may be necessary, just four bolts), and you are done. Also you could have a bad battery. GM’s CanBus System requires 12 volts to function properly. The sound of your engine should indicate when your car/ truck is not getting enough voltage.

My 2007 Chevrolet Silverado was doing the same thing I changed the throttle body and that fixed my problem.

I had the same problem with my 07 Tahoe 5.3L, I would drive around for a while and those lights would come on, say service TC and Stabilitrak, then cut power and go into limp mode. The repair was pretty simple I just bought a new Throttle Position Sensor (~$50) and installed it at home and now it's good as new.

Mine is doing the same thing took the bed off to have body work done and noticed the wires for the abs had broke I agree with couch audio check abs wires and wheel bearings

check your intake make sure all hosses are pluged in (airlines)

Your Service Stabilitrak error did not illuminate until you had turned your steering wheel At the 1:12 mark. This tells me that it's your steering wheel position sensor. I had performed many tests eliminating everything that wasn't the issue. This SAS (Steering Wheel Angle Sensor) was my problem until I had replaced this part.

Check the spark plug wires. Look inside the wires. One of my wires was burnt. Causing the issues.

2011 tahoe - replaced with bigger battery cables. Been good since. Did it 6 yrs ago. Factory cables have bad crimp and has a service bulletin from chevy about it.

On the 2011 Silverado, I have the same issue. It is a sensor that is located in the steering column. There are 5 total, 1 on each tire and the 1 on the steering column. I was quoted $385 from my local Chevy Dealer.

I had the same problem on my yukon denali 2007 and changed the steering wheel position sensor and i got it fixed

my 07 yukon have the same problem 2yrs ago, change the brake pedal switch and fix the problem, check your brake lights!

Chevy Stabilitrak and Ford Advancetrac - systems designed to extract money from your bill fold.

I fixed mine with an accelerator pedal sensor same issue on my 2008 escalade.

Hi, I feel your pain. I had the same problem. It all started with a "Low oil pressure" signal that went to a "turn off engine now" message. I did, let the truck cool down and restarted. kept getting same message, checked oil and it was fine. Went to a mechanic who said it was probably fine just an error on the computer but he couldn't get to it right now. Later that week while driving down a highway I heard a clunk sound and started getting an error message "check stabilitrak" followed by "check traction control". Those went to "service stabilitrak and traction control". The truck started running very rough, wheels felt as if they were going to fall off, etc..My husband checked the error codes and it said that we had a misfire on #4. He changed out everything he could, spark plugs, wires, wire housing, etc. No help. It was running so rough we had to have it towed to our mechanic...he had it for over a week and couldn't find the problem. He suggested we take it to a dealer. He felt it was something internal. We had it towed to another mechanic that was recommended by a friend. He found the problem and fixed the truck. Here is what he did that solved our problem: Changed the valve lifter (it was bent in position #4) since he had to go inside the engine he went ahead and replaced all four on that side. As a result of having to open the engine he also had to replace the head gasket, replaced the oil, replaced the anitfreeze, His diagnosis: Intake lifter on #4 cylinder collapsed. Cost: $1534.24. FYI...I drive a 2009 Chevy Avalanche. I hope this information helps all who are having the same or similar problems. Good luck.

I have the same problem with mine when my car would sit and idle for a few minutes when the weather with cold. I would have to disconnect my battery to get my truck to run right again. After disconnecting the battery the check engine light would stay on for a little while but it would eventually go out as well

Hi .Could you share how did you fix this?

I just started having the same issue. I have a 2009 Chevy Silverado 1500 4.8L

MrBosanacBIH not sure if u got that fixed yet but i just bought the same truck and it is doing the same thing. What i noticed is it comes on as soon as i turn the wheel not when it is rolling. I noticed that yours is doing the same per your video, fyi. I looked it up and it is a sensor on your steering column by your knees. KZfaq it. Have a gooder :)

I had a similar issue on my 2011 Chevy Silverado where occassionally, when driving, the traction control and stabiltrak lights would come on, and the tachometer would stop working, or sometimes the truck would be hard to start. No code was being thrown at first. I tried a few things but nothing worked. I did some other work to it where i changed the plug and wires, replaced the water pump and thermostat. During that job I disconnected the battery and the issue went away for two weeks then came back and threw a code. Turns out it was the crankshaft position sensor. I replaced that and no issues for the last 5 months. Part was about 50 bucks. Could be different for you, hook up an ob2 scanner and check if any codes then go from there. Hopefully this can help someone.

I got service traction control and abs light and my cruise control didn't work,. Changed brake switch and that fixed the problem

Steering Position sensor and R&R Steering wheel sensor are listed on my bill. It defenately fixed it $180 total parts n labor 2012 Silverado LTZ

I thought that I had this licked and now I don't know. Just ordered the Steering Wheel Position Sensor and SLS587 Stoplight Switch. If not, I'll have fun under the dash all cramped up, great times.

It's the Steering Wheel Position Sensor. Look it up

Happening to my 2015 silverado

Does warranty cover?

i had traction control and brake light on. checked the brake fluid and i had half. filled it up to max and all lights took off 🙏

Best thing is but a ford or something before you’ll start hating yourself for not doing it sooner but in this case usually the dealer will remove the code or possibly you can use a obd2 scanner to remove code but most likely it’s gonna come back so best to get it fix

09 silverado experiencing Stabilitrack and service trailer brake... Any suggestions

Any insight is appreciated. I was driving down a heavily washboarded road dog about 50 meh when I simultaneously had ABS, Service Traction control, Service Stabilitrac, Service Trailer Brake Control Module. (factory). I also intermittently have the parking sensors disable from time to time then enable on their own. I had just ordered new tires and when I was dismounting the rear off the truck I noticed the rest brakes were down to about 10% life and fronts were 80% installed new rear pads hoping that would at least fix the ABS light. No broken wheel speed sensors/ wires, nothing, after everything I could think of, I'm still at a loss. Any ideas. 2009 Silverado K2500 HD 6.6L

I am having this problem, what’s was the cause of the that light I re did a ground I changed the two abs wheel sensors I cleaned my air system and still the same

I have a 2013 Chevy Silverado Crew Cab 5.3L. The stabilitrak and traction control lights come on and off with the engine light blinking. Went by the auto store and had them run a diagnostic and it came up 3 misfires on Cylinder 1 and a ABS code that they had no idea what it meant. I replaced the plugs about a year ago and one side was fouled and to other were fine. I've got coils and wire coming to change them out but the ABS code has when wondering. Would like some guidance for this if you have some knowledge. Thanks

Check your brake fluid level if it's low the sensor will get service brake message

Video is old but it could be Wheel Hub bearing beginning to fail. Keep driving like that the wheel bearing will fail brake light will engage and hopefully you stop in time

Just recently had the issue while driving on ice and sleet. In addition, Reduced engine power came on and the motor died. A bit unnerving on the interstate with traffic.

I’m having the same issue in my 2011 Chevy Silverado 5.3L. A few months ago when it was extremely cold, the light and warning for traction and stabilitrak didn’t come up until I was curving on the road after taking an exit from the highway and all of a sudden the truck went into ABS mode. It scared the shit out of me and good thing there was no one behind me. After the ABS kicked in, the service traction control and stabilitrak lights came on and traction was turned off so I was able to continue on my way. I have a feeling it may be a speed sensor on the wheels or maybe the steering column but I haven’t had a chance to look at it. Anyone else with similar symptoms while out on the highway?

i also have the same problem with my 2011 silverado. dealership told they wanted $100 just to read the codes and diagnose the problem. so any chevy dealership should be able to atleast do that. im still doing my own research online 1st at the moment.

I was having the same issue with my 13 sierra 1500 , man i hate it it was a misfired cylinder 4 had to change one of the lifter did the whole tune up first they nothing kept doing the same so i changed the deactivation solenoid then last thing had to replaced the oil pump because oil pressure fail after changing the oil pressure sensor , swear i was about to throw this truck in the garbage but finally got it fixed now everything in back to normal ,, it didn’t have nothing to do with the abs system ,, i also changed the valve covers

I have the same problem..chevy express 2017..the dealer said its an old code...i don think so..

I had the same problem check your spark plugs, high miles

Did u check brake fluid my came on with the brake light put fluid no more lights

I have the same problem with my 2012 Tahoe have you found a fix? two mechanics new tires 2 alignments and still no one can tell me whats wrong or how to fix it

I reprogram my throttle body on my 2010 camaro v6 bc of the check engine light. Now I get a stabilizer alert, now don’t know what to do...

2013 Silverado same problem. Codes supposedly shows that i need to replace MAF & of ABS Sensors.

I was having same problem it was the engen fuel injector dirty wat's they canntion I don't know really

It's the wheel speed sensor Scana it'll tell you what size bad

I had this same problem with my 2011 Impala SS. Fuel pedal sensor

Have a 2013 Tahoe same issue.....its a steering wheel sensor

they same mess kept poppin up so i ended up putting in a 2in leveling kit because i had some mud grips on it and i had to get a front end alignment and that ended up fixing it. I hope this helps somebody

Wow, after reading all the comments, I’m figuring that fixing this truck is going to be a freaking turkey shoot…. I’m starting with an idler arm and a new steering stabilizer shock since it doesn’t have one…. I’ll post more, maybe even the fix… if I can find it….

My 11 suburban does the same thing and since the last snow storm it won't shift out of 4w low.... so I really can't drive it on the road (over 40 mph) ..

Must of the time it is a grounding issues my 2011 chevy suburban had it cleaned terminals and did some research on how to do a better ground and that fixed it. But if you have a reduced engine power that going to be your throttle body sensor and your throttle body might need cleaning. Clean first then replace sensor takes 15 min from cleaning and pulling back off to replace throttle body sensor

Do you have a slight rough idle bc I do! mine is making the same thing??

I just had that happen on my 2007 avalanche LTZ. The traction control light came on and it said service Stabilitrac and service traction control and was shifting hard going into second gear. I had been having battery problems prior to this and thought that that might be the reason. I just put a new battery in there and it fixed it.

Mine is doing this and flashing "Service 4 Wheel Drive". Is a newer Sliverado too. Im so fed up with it. Thinking about trashing it and getting a Tundra instead. Smh...

I have this same problem. Weird thing is, it doesn't come on in the morning, when the day temperature is cooler It does come on in the afternoon, when the day is warmer.

Could be the brake sensor causimg this

im getting same thing but if im driving on highway crusing at 65-75 MPH and when light comes on itll drop down to 3 gear and stay there if i pull over to a hault it will shift down to 1st gear. no its not my transmission i just got it rebuild by the best shop in town and im over this s*** it happened to me a few times already while i was driving. and it goes away sometimes if i turn off truck completely and turn it back on. WEIRD

Have you seen the video by J Gary, he changed a sensor on the brake pedal and said it was a $25 part.

that's why I drive old cars NO stupid sensors no nada..think about it ..is all business of course they know u don't want to see nothing on the dash board so they come up with all kinds of stuff to have u spending more.. OLD CARS RULE!!

2011 Chevy Silverado 1500 LT 5.3L V8 - Check engine light, stabilitrak light, and tire light all on. Check engine light blinks. The tire light came on after I got a flat and replaced with the spare tire the other day. Waiting on shop to get the new tire in. Check engine light came on before this at some point. After the tire light came on, stabilitrak light along with service traction control warning populated. Going to check for codes later today. Any advice is much appreciated.

Hi sir.. ihave toyota avalon 2012.. There are no any lights or symbols in the dashboard board, but suddenly while driving the check engine and trc off lights turn on, and the traction control shows up also but disappears after 5 seconds then come back again , icant drive the car with this situation. So can you help me with this issue... Thanks

I took mine to the shop to replace the rear seal... and wen I was driving back home the traction control and stabilizer came in ... went back to the mecanic... and he told me IS THE MOTOR MOUNTS OR THE TPS, OR THE CATALIC CONVERTER, OR THE COMPUTER YOUR ENGINE IS GOING BAD, BUT U CAN CHANGE THE SPARG PLUGS AND WIRES IF THAT DOESN'T FIX IT, BRING IT BACK AND WE SE HOW MUCH IS GOING TO BE TO FIX IT... I replace the wires, spark plugs and still the same. And I'm not going back with that (mecanic ) she was good and now i got a big headache

A nice enough scan tool will read what it is for me it was my steering angle sensor.

was happening to me and i found out what it was . wheel was straight but it had a -180 offset. had to set it to 0. and hasnt turned on since

YOU NEED A STEERING POSITION OR STEERING ANGLE SENSOR

problem caused by GM Engineers designed with fuels management. the lifters inside engine need to replace all. GM 2007 to 2017 if you lucky it can drive 120k miles, it cost $3500, i have my fixed last month it run like new now. take to the shop have them estimate for you. my 2007 Yukon 5.3 engine. with 110k miles on it.

Having the same problem on my 2010 avalanche hit new rear struts got back in the car and seen the triangle brakes warning and rear stabilitrack off also I just seen my brake fluid is short of full can anyone help me?

Have you found a solution? Mine comes on after a while on the road, and sometimes there is vibration or knocking before it comes on.

My 08 GMC Sierra started doing the same. I also found that my brake lights stay on because of a faulty brake pedal sensor. Also, I need to replace sway bar links so all of that may be it. Hopefully you got it fixed.

I have a 2011 Tahoe LT with 158k miles on it. I replaced both front hub assembly's the first week of June, so almost 3 months ago. After I filled up with gas I got in and started the truck. I got the stabitrak and ABS lights along with the service messages. I drove it straight to the dealership which was only a 1/2 mile away. They put it on the computer. They told me my left front speed sensor was malfunctioning and my right hub assembly was loose on the inside. I don't really believe them after reading these comments and other video comments. The first week of June I also replaced the "brake switch" under the steering wheel because my cruise control wasn't working. Does anyone else have any other things it may be?? Thanks y'all.

Me too! But I drive in snow so when the light kicks on after about two minutes of driving my steering turns to shit and it drives like a 2WD piece of crap. It’s obviously disabling the traction control as well

i have the same problem

i just change out my BLS about a month ago to fix my crusie control.... now i have this same problem with this traction control and stabilitrak....

I got the same thing going on in mind started with low oil pressure

It’s just a loose connection I put a shim over the connector haven’t had any problems since

Check your wheel speed sensors

I started smelling gasoline a week ago. Just today these lights came on and the truck doesn’t idle the same as it did before. I’ll do a follow up after I take it to the shop.

Car has same problem but light pops on at random at rpms stutter and car struggles to gain speed and feel like it hops. I dont even know where to begin looking

I have a 2011 Tahoe Hybrid, I have the same problem. Had it at the dealer, they change the oil sensor since the oil gauge was acting up and had the computer module installed and reprogrammed. Drove it 80 miles and back to square one with the triangle light on and the engine light one and the power at half power and the two codes StabiliTrak and service traction control and a message saying service brakes. I then watch a video that said to change the Brake Switch. it was $25 and i did. It still didnt help. Dont know what to do.

Okay so my 2011 chevy avalanche LTZ rear left tire had a nail and so we went to a shop to patch it cuz the stabilizer and break light went on. When they patched it it went off then a week later it's back on again. Just took it in to the same shop and they cleared it and right when I reached home the damn lights came back on. CAN SOMEONE HELP ME PLEASE.

I just had the same problem on my way to work on a 2010 silverado 5.3 lt the engine light came on so the traction control came on but my idling it’s really rough the engine sakes a lil and makes a mocking sound

Ami se me prendiron las mismas al cambiar amortiguadores en ningun lado me las pudieron arreglar investigando resulta q por la altura del tornillo del amortiguador lleban un sensor aparte de el del amortiguador por arriba del chasis se desconectaron por accidente y los reegrese quedo como nueva suerte

This can be very dangerous,was driving home today ,on interstate @70 mpg ,the transmission went into low gear twice ,lost power ,door locks up and down,abs light came on , traction control and stabilitrack light on ,

Try turning wheel before putting in gear. If it comes on it could be steering wheel position sensor.

Has anyone gotten a solution?!

It's not when you start rolling, it's when you turn the steering wheel, I don't know why this causes the light to come on but mine is doing the same thing as well

happen to me and first i check brake oil found it low , add oil and everything ok

Lol, that was a question, not a video of how to fix it

What can I do my abs and stabilitrack turn on and i cant put it in reverse i need help

I have the same problem i have a 2010 Silverado 1500 LTZ and my lights come on when i hold my back for a period of time then traction control and abs comes on

Mines doing the samething

Fuse FIRST !!

i had the same problem all what was needed was brake fluid added then lights cleared

Disconnect the battery like for 10 seconds and then connect the back and turn on the truck it going to be good

My truck does that only in the day time when its hot,no problem at night...

brake switch on the pedal brake cost you around 20 buck's