2012 Acura TSX Bumper and Headlight Removal- Vlog #35

No video

2012 Acura TSX Bumper and Headlight Removal- Vlog #35

Рет қаралды 98,895

Күн бұрын

In VLog 35, the driver's side HID bulb has burnt out after 42k Miles. I've looked around and researched how to change it because simply it isn't accessible via the engine bay. There were suggestions on going through the fender liner (I had no such success) I couldn't fit my hand due to the frame being in the way.
I then decided I would remove the front bumper and remove the headlights and replace the bulbs with as much room as possible.
Check out how that is done in the vlog. Not a hard job to do, just time consuming.
D2S Bulb (8000k): amzn.to/2NK087P
Feel free to share, if you share please hashtag #epicjontuazon
Subscribe ► / epicjontuazon
Facebook ► / epicjontuazon
Instagram ► / jontuazon
EpicJonTuazon ► epicjontuazon.com
Twitter ► / jonathantuazon

Пікірлер: 201

@smbmxdirt3427 5 жыл бұрын

Mine was flickering today. I can't wait to struggle to try to fix it.

@danielbailey553 2 жыл бұрын

A couple suggestions, if you also need to change your high beams and upgrade your fog lights to LEDs for example, now's the time to do it. All at once with easy access for everything. One additional hot tip, now is the time to polish your headlights while they are away from the paint. It's really easy and fast

@EPICJONTUAZON 2 жыл бұрын

👍👍👍 Excellent points!

@newunderthesun7353 5 жыл бұрын

Old video but still useful. Gave you a thumbs up because your's is the only video that actually shows the in-between steps everyone leaves out.

@EPICJONTUAZON 5 жыл бұрын

haha thanks! I like to be thorough :)

@toddmarshall1582 4 жыл бұрын

Thank you. Your video was very helpful. I had no luck getting in through wheel well to service the lamps, too. Used WD-40 on push locks. It really helps to not to break them when disassembling.

@EPICJONTUAZON 4 жыл бұрын

🙏🙏🙏

@junkimchi Жыл бұрын

Thanks for the steps. Easy to follow video with good advice.

@EPICJONTUAZON Жыл бұрын

Glad it was helpful!

@tomdolgin5441 4 жыл бұрын

Nice video. I did this, but without removing the bumper and headlight housings. Let me just tell you that I will never do that again! Took me 3 hours! The worst part is getting the igniter ground plugged back in.

@EPICJONTUAZON 4 жыл бұрын

easier with the bumper off and headlight housing off 😁

@fgdghfhjgfjgfhjhgjgh 7 жыл бұрын

This was very helpful.. could you post the link for the Bulbs. so i can buy the exact one.. its the 6000K?

@EPICJONTUAZON 7 жыл бұрын

Thank you yes the link is here: amzn.to/2p97eqz

@c0mikal310 3 жыл бұрын

Good comment on the clips under the headlight !

@JT-sk5nw 3 жыл бұрын

Thanks for the video, this will help about when I replace my headlight assemblies in the spring!

@EPICJONTUAZON 3 жыл бұрын

No problem 👍

@HamBawlz 7 жыл бұрын

I used to live a few houses down from you in that complex with the modded silver tsx; used to own a silver wrx bugeye wagon, too. my left hid ballast died this week. thanks for the vid.

@EPICJONTUAZON 7 жыл бұрын

+D. Tran Awh man sucks! should've hooked up for a shoot! Dang sorry to hear about your ballast, glad this video will help!!!

@joserubio8649 3 жыл бұрын

This man is a genius, well made video

@EPICJONTUAZON 3 жыл бұрын

🙏🙏🙏🙏 Please subscribe!!!

@ericknavarro8772 3 жыл бұрын

Yo this video helped a lot! I’ve been nervous to do it myself for a while so I would pay a guy to do it. Figured it was about time I did it myself and it’s not so scary anymore. Turned into about 2 hours of frustration and fun!

@EPICJONTUAZON 3 жыл бұрын

👏👏👏 Good job! Glad the video helped!

@luixanderton 4 жыл бұрын

Thanks much, your video is awesome. I just changed the bulbs my on Acura TSX 2009. Dealer wanted to charge me $600.00 dollars here in south Florida

@EPICJONTUAZON 4 жыл бұрын

😱😱😱😱 glad I could help!

@driverslineocsz4418 4 жыл бұрын

😒 stealerships

@MRskyliner91 6 жыл бұрын

Great stuff mate, really appreciate you taking the time to make a video of this

@fernandosolano1623 5 жыл бұрын

Thanks!!, saved me alot of money on my 2011 Acura TSX

@EPICJONTUAZON 5 жыл бұрын

🤙🏼🤙🏼🤙🏼🤙🏼

@LoonToon24 6 жыл бұрын

Dont hid bulbs have like a wire connected to them ?? These don't

@EPICJONTUAZON 4 жыл бұрын

You attach the igniter once the bulb is seated

@christianmaibach1299 7 жыл бұрын

thx. it worked for my Euro Accord as well thank you

@EPICJONTUAZON 7 жыл бұрын

Christian Maibach you're welcome! Glad the video helped! Please consider subscribing! 🤘🤘🤘

@tfirik Жыл бұрын

If we remove the bumper clips without breaking them, can we use the same clips or should we get new clips?

@EPICJONTUAZON Жыл бұрын

Yeah you can reuse them.

@TowProVlogs 14 күн бұрын

Super helpful bro

@mihailmilanov456 Жыл бұрын

I've managed to reach it, through the hood when removing the battery. It was difficult but not soo much.

@EPICJONTUAZON Жыл бұрын

Nice! Glad to know you can go that route!

@HellZell99 8 ай бұрын

Can the 2012 bumper fit on a 2009?

@TheFamedwarrior72 7 жыл бұрын

Excellent video! About how long did the job take? I think I'll hit subscribe.

@EPICJONTUAZON 7 жыл бұрын

Probably 1 hr end to end. Just take your time and be careful with those plastic clips. Thanks for the support man!

@Elheino 2 жыл бұрын

Thanx great video.

@EPICJONTUAZON 2 жыл бұрын

🙏🙏🙏

@briantano1248 7 жыл бұрын

thank you!

@EPICJONTUAZON 7 жыл бұрын

+Brian Tano you're welcome brother!

@ben5yt Ай бұрын

Thank you very helpful once you found the 4th screw. My self at least I hear what I need to and then I stop watching. Would be nice to edit the initial screw could as I was confused and had to watch further for you to realize you meant to say 4 screws.

@adamwarlock7158 7 жыл бұрын

Ohh. hope you adjust those headlamps after the project

@EPICJONTUAZON 7 жыл бұрын

+Adam Warlock why would I need to adjust the headlamps? just swapped out bulbs

@Mao2187 2 жыл бұрын

Great job.

@bigkev26 2 жыл бұрын

Thanks bro.

@EPICJONTUAZON 2 жыл бұрын

🤙🤙🤙

@sulemavasquez8261 2 жыл бұрын

I have a 2012 Acura Tsk and not able to find a way to adjust my light bulbs.. any suggestions?

@EPICJONTUAZON 2 жыл бұрын

Adjustments on the light bulbs are typically on the bulbs themselves there are some angulation screws. Depends on what bulbs you have.

@sulemavasquez8261 2 жыл бұрын

@@EPICJONTUAZON I bought D2s HID Headlights low beams 6,000 k and Sylvania 2 Halogen lamp bulbs 12.8v, 65 w, white lights , hope that makes sense, are these the wrongs ones lol

@EPICJONTUAZON 2 жыл бұрын

@@sulemavasquez8261 no they sound like the right ones. You won't be able to adjust the high beams. The HID bulbs themselves you won't either. I got confused with LED bulbs for a sec. On the back of the headlight housing there should be screws to adjust the level of the beam you'll have to take the headlight out make an adjustment and put em back in to see where they line up.

@sulemavasquez8261 2 жыл бұрын

@@EPICJONTUAZON awesome ! We will try that, hopefully it works . Thank you so much for your help

@s_nt_i8961 6 жыл бұрын

Thanks mate this video it's very helpful. You hit save my time.

@EPICJONTUAZON 6 жыл бұрын

Thank you! I'm glad it helped! No point in wasting time! Please consider subscribing!!

@iveriani 7 жыл бұрын

Do you have a link where I can buy OEM speck high beam light bulbs and turning signal light bulbs...I plan on replacing all mine......for my Acura Tsx 2012...Great video....

@EPICJONTUAZON 7 жыл бұрын

Yes here you go! High Beam: amzn.to/2fyr2jv Turn Signals: amzn.to/2vq4irg

@iveriani 7 жыл бұрын

EpicJonTuazon Thank You!

@roronoa3327 3 ай бұрын

What tools needed

@EPICJONTUAZON 3 ай бұрын

Flat head screw driver and some socket wrenches

@web-hz3tz 7 жыл бұрын

Nice video, when you had the headlight unit out could you see where the left-right beam alignment is? The up-down is in plain sight but I can't find the other.

@EPICJONTUAZON 7 жыл бұрын

+web 293769 not sure I understand your question. The projector beam is set, you can't raise or lower it.

@web-hz3tz 7 жыл бұрын

EpicJonTuazon , I had to have one of my headlights replaced on my 2014 tsx se and it looks like the projector beam is pointing toward the center of the car vs it being straight. I can easily find the adjustment screw for the up-down alignment of the light but can't find the left-right to make the beam straight. I was going off the symbols on the headlight housing "maybe there isn't on for left-right adjustment" Sorry if I wasn't clear before.

@EPICJONTUAZON 7 жыл бұрын

web 293769 hmm not sure about that. Never encountered leveling of the light.

@dablordofnibiru9857 3 жыл бұрын

This was a very helpful video. Very thorough and easy. I swapped my headlights with new ones. Only thing he doesn’t mention is when you disconnect the battery you will need a code to reset it. Got to wait the weekend to call sewer for proper code

@EPICJONTUAZON 3 жыл бұрын

The code is in your owners manual 😉

@dablordofnibiru9857 3 жыл бұрын

@@EPICJONTUAZON dope man I’m about to rip through it right now thank you so much

@EPICJONTUAZON 3 жыл бұрын

@@dablordofnibiru9857 👍👍👍 good luck!

@xtcnrice 7 жыл бұрын

Great video! I thought about using a flathead to free the bumper from the annoying clips, but I was really worried about the flathead scratching the paint on my bumper. Was it difficult to maneuver the small flathead without rubbing against the bumper? Again, great video! I'll probably use this going forward :)

@EPICJONTUAZON 7 жыл бұрын

+Gary Phung Thank you! Please consider subscribing! they make a special tool for it! but no if you wrap it with a cloth you should be fine!

@yoballs9060 3 жыл бұрын

is there any way to adjust the bulbs you just did? I see the running adjustment nipple but not the one for the bulbs you just did. Does any one know how to adjust it?

@tubeman62 3 жыл бұрын

Thanks! Nice job on the video!

@EPICJONTUAZON 3 жыл бұрын

👍👍👍

@elmuzaadventures2259 4 жыл бұрын

Whats the connect for the white switch. I can’t find it:/

@mgoonkilo6086 4 жыл бұрын

I need help putting the bumper back together. Please upload a video or anybody have a video on how you put the front bumper back. I did everything but couldn’t get it to line up or something hold it to push it in the clips

@kingroll7026 2 жыл бұрын

Does car burn oil?

@EPICJONTUAZON 2 жыл бұрын

Negative

@kingroll7026 2 жыл бұрын

@@EPICJONTUAZON thanks, I plan on buying one

@EPICJONTUAZON 2 жыл бұрын

@@kingroll7026 makes for a great dd

@llineedsadragstrip4089 5 жыл бұрын

good video well spoken not too much camera shake thumbs up bro

@EPICJONTUAZON 5 жыл бұрын

🙏🏼🙏🏼🙏🏼 Ty

@black5corpion76 7 жыл бұрын

nice.. I have 2013 model ..i guess is the same way..

@EPICJONTUAZON 7 жыл бұрын

+black5corpion76 should be very similar. do check though if you can fit it through the engine bay before you go removing the bumper!

@alobando9690 5 жыл бұрын

Thank you, one of the best!!! Way to go

@EPICJONTUAZON 5 жыл бұрын

thank you!!! please subscribe!

@SmasheDITAman 6 жыл бұрын

Hi, great video explaining this process! Subbed because of it! Just a quick question, as you got 6500k HID do you think this will closely match with 6000k LED DRL/high beams as currently, as stock, they look too much apart colour wise, and I want them to be as close as possible?

@EPICJONTUAZON 6 жыл бұрын

Thank you!!! I think the OEM high beams are closer to 4000k. They're more yellowish than white IMO

@SmasheDITAman 6 жыл бұрын

Yeah, I have replaced my High Beams to 6000K LED, so I was wondering what colour temp HID to get to match closely to the High Beams colour wise? I'm am debating whether to get 6000K HID or 6500K HID, if you could help? Thanks

@ptftg 3 жыл бұрын

great video! I'm going to need to do this as my left hid is turning pink. did you have to adjust the headlight aim after doing this?

@EPICJONTUAZON 3 жыл бұрын

Would be a great time to check before putting the bumper back on!

@ptftg 3 жыл бұрын

@@EPICJONTUAZON thanks!

@waseembux7537 5 жыл бұрын

Hi . Is it possible to remove the orange amber reflectors in the head lights and .and then all clear ?

@EPICJONTUAZON 5 жыл бұрын

anything is possible. you would have to heat the adhesive off the lens to remove the plastic covering and then either spray it chrome or black.

@xd1771 2 жыл бұрын

Have these lights had any problems over time?

@EPICJONTUAZON 2 жыл бұрын

So far so good. No issues currently.

@hauberty 3 жыл бұрын

This is gold, thanks!

@EPICJONTUAZON 3 жыл бұрын

👏👏👏 You're welcome! Please consider subscribing!

@Namudi2 3 жыл бұрын

Thanks man helped me alot

@EPICJONTUAZON 3 жыл бұрын

🙏🙏🙏 Glad it did!

@reeses2011cup 6 жыл бұрын

Awesome video very informative

@EPICJONTUAZON 6 жыл бұрын

Teresa Fairley thank you! If you need any info let me know 🤘🏼😎

@agusrodriguez1 4 жыл бұрын

my car is 2011 (acura tsx). is there a way to replace the low beam without removing the bumper?

@EPICJONTUAZON 4 жыл бұрын

From my experience no, otherwise this video would not exist lol

@rajsandhu8884 5 жыл бұрын

Hi bro, just wondering how hard it is to change the cluster....?? And how to do it...?

@anthonymessihv 4 жыл бұрын

Why do you want to change the cluster?

@Tigz09 6 жыл бұрын

Thank you very helpful i will be doing this in 2 weeks time but im getting my inner light plastic sprayed black and the indicator cover taken out my Euro is black and i can't stand the yellow indicator covers. Mine is a 2010 Accord Euro from Australia id assume to take off my bumper and light removal would be the same as this. Thanks again

@EPICJONTUAZON 6 жыл бұрын

Tigz09 word! Glad I could help! Good luck 🤙🏼🤙🏼🤙🏼

@MRskyliner91 6 жыл бұрын

Hey mate, can confirm this is the same for Australian models, did mine and followed this video! Worked a charm!

@Dionesus 6 жыл бұрын

I have a 2011 tsx. When i turn on my car...the light turns but then slowly turns amber. After like 15 secs...it shuts off. Do you think that is a bulb prob or ballast?

@EPICJONTUAZON 6 жыл бұрын

I would try replacing the bulbs first. That would be the cheap and easy fix. If it continues to happen with a new set of bulbs then you know its probably the ballast.

@wongelfski4681 6 жыл бұрын

Well I hope you put in LEDs so you don’t ever have to do that again

@EPICJONTUAZON 6 жыл бұрын

Wong Elfski LOL did HID bulb swap. May end up doing it again down the road. Maybe do quick release buttons in the next video! 🤘🏼🤘🏼🤘🏼

@rezh.6193 4 жыл бұрын

Nice video man.

@EPICJONTUAZON 4 жыл бұрын

Thank you 👍👍

@andyp1031 6 жыл бұрын

Hey would the sylvania zxe 9005 bulbs work good like the ones you used? My driver side headlight just burned out lastnight and I need to replace it. Great video by the way!

@EPICJONTUAZON 6 жыл бұрын

9005 bulbs are the high beams. You'll need HID bulbs which are something like D2s Bulbs.

@andyp1031 6 жыл бұрын

@@EPICJONTUAZON oh ok good to know, my TSX is a 2009, what bulbs did you get? Where did you buy them? I'll just use those since they looked real good in yours. My high beams work fine. It's the regular headlights I need

@EPICJONTUAZON 6 жыл бұрын

amzn.to/2NK087P

@andyp1031 6 жыл бұрын

@@EPICJONTUAZON thanks dude I appreciate it! , great vids too!

@1GTASANANDREASCJ 7 жыл бұрын

On the passanger side it's fairly easy to replace the blub but on the drivers side...no chance. Even my car dealer remove the bumper, because it's much easier

@EPICJONTUAZON 7 жыл бұрын

+1GTASANANDRESCJ yeah It was more worth it for me to just to remove the bumper bc I was changing both bulbs. Good to know tho! Thanks for the tip!

@1GTASANANDREASCJ 7 жыл бұрын

+EpicJonTuazon one thing is different to mine Honda Accord (live in Europe, they sold these as Hondas): the wheel arch do only have one screw on each side. Do you have a sport package? Maybe that's why you have three screws.

@EPICJONTUAZON 7 жыл бұрын

+1GTASANANDREASCJ its a special edition. Not sure if that really makes a difference.

@thepatel5004 6 жыл бұрын

my Honda Accord in the UK has the three screws though, so it may be the case, because the special edition one has a lip on the bottom of the bumper in the UK

@PandaLuv925 6 жыл бұрын

Hey, after two years, are the light bulbs still working OK?

@EPICJONTUAZON 6 жыл бұрын

bulbs are still good and kicking.

@jeffryjimenez07 6 жыл бұрын

Thanks man for this!

@EPICJONTUAZON 6 жыл бұрын

Jeff Jaquez Jimenez you're welcome!

@pauls8620 5 жыл бұрын

How long did those bulbs last you bro? Thinking abt getting those

@EPICJONTUAZON 5 жыл бұрын

Still kicking man!

@iveriani 7 жыл бұрын

Quick question: Where did you buy your HID headlight bulbs? I saw the link you gave in your comments and I order but when the light bulbs came they were not in the official box like you had in your video...could you post the link again and confirm if the ones I got from Amazon is good? The box is just plain white...

@EPICJONTUAZON 7 жыл бұрын

Are you referring to the HID bulb?

@iveriani 7 жыл бұрын

EpicJonTuazon yes

@EPICJONTUAZON 7 жыл бұрын

as long as they are D2s Bulbs they should be fine. Is the temperature the same? 6.5k?

@MrHowiezhu 5 жыл бұрын

@@EPICJONTUAZON is 6.5k the OEM color? i read OEM uses 4.3k.

@junelsvtecturbo777 5 жыл бұрын

thank you for the video

@EPICJONTUAZON 5 жыл бұрын

You're welcome 🤙🏼🤙🏼🤙🏼

@kingShadow777 7 жыл бұрын

it did help thank you I just bought a 09 Acura and I will like to know how to remove the logo in front of the bumper cause mines is all scratch can you Help me out?

@EPICJONTUAZON 7 жыл бұрын

Alejandro Pagan Castro glad it helped. I believe there's some clips on the back of the bumper.

@kingShadow777 7 жыл бұрын

ok Thanks also what about the headlights is there any recommendation to get black halo? a good place to buy them?

@EPICJONTUAZON 7 жыл бұрын

Alejandro Pagan Castro you want halos in ur headlights? I'm not sure about black specifically but I'd recommend Lightwerkz in NJ they're a great company to start with!

@luisperezrodriguez4007 4 жыл бұрын

Good one but next time show your work leds on

@tomdolgin5441 4 жыл бұрын

When changing my hid bulbs, I could t get the little top white connector back in. But the lights still work. What exactly does that wire do on top? Does it just hold the ballast in like you said? Thanks.

@dresmith6706 4 жыл бұрын

Can I put the led in the head light an if so what's the model I see ds2 but I can find in leds is there like a substitute like 9006?

@EPICJONTUAZON 4 жыл бұрын

You can use leds for the high beams but not replacement for the low beam as they are HIDs

@dresmith6706 4 жыл бұрын

@@EPICJONTUAZON so I only can change the fog lights too ?

@EPICJONTUAZON 4 жыл бұрын

@@dresmith6706 I havn't tried the fog lights but I do know some of the LED bulbs wont fit the fog light housing so just be aware of that.

@dresmith6706 4 жыл бұрын

@@EPICJONTUAZON oh okay thanks this thing is mad complicated

@EPICJONTUAZON 4 жыл бұрын

@@dresmith6706 lol I feel you

@danteg223 3 жыл бұрын

Im about to do this tomorrow morning bcs i tried the other way (going in blind) and it was awful and i dont wanna keep messing anything up since its really hard to connect the ground cable back (again going in blind) so anyone wjo tried this and worked, how long does this process take?

@chinchy111 3 жыл бұрын

yeah i got the bulb out through the engine bay but that damn ground cable i couldnt get back on so i gave up. did you take the whole bumper off

@josephhermans145 7 жыл бұрын

Thanx was very helpfull!!!

@EPICJONTUAZON 7 жыл бұрын

Marta Krawczyk 🤘🤘🤘🤘

@luisvazquez9057 6 жыл бұрын

I need help getting those lights please😁 and the name of them,cause my acura needs it too

@EPICJONTUAZON 6 жыл бұрын

The bulbs? they're direct HID replacements. Link should be in the description!

@luisvazquez9057 6 жыл бұрын

EpicJonTuazon ok i will see i like the video bro

@luisvazquez9057 6 жыл бұрын

EpicJonTuazon can't find them

@EPICJONTUAZON 6 жыл бұрын

Here you go! D2S bulbs! amzn.to/2td6Xm1

@luisvazquez9057 6 жыл бұрын

EpicJonTuazon thnx bro is it just for 1 bulb or does it have both

@Exphia 5 жыл бұрын

i changed mine without taking off the bumper im just here to see how to take the bumper i gotta change ac condenser

@EPICJONTUAZON 5 жыл бұрын

That's very impressive 👏🏼👏🏼👏🏼

@henrytaylor5047 4 жыл бұрын

Really want to try this , would you guys consider this beginner level ?? I’m tryna save 100 bucks !

@EPICJONTUAZON 4 жыл бұрын

100% I've never taken this bumper off before this video.

@henrytaylor5047 4 жыл бұрын

EpicJonTuazon , Great news, definitely subscribing man. Just got this car and your videos are on point. Thanks again

@EPICJONTUAZON 4 жыл бұрын

@@henrytaylor5047 🙏🙏🙏 good luck thanks for the support

@henrytaylor5047 4 жыл бұрын

Hey at 7:45 ..What is the aluminum piece that detaches from the bulb called , it has the braided cable attached ( found out mine was burned completely). Thanks for the help , was able to get my bumper off easy !

@EPICJONTUAZON 4 жыл бұрын

@@henrytaylor5047 I think it's a ground cable but I'm not certain.

@drkshark 5 жыл бұрын

Doing mine today thanks bro, give my videos on my tsx a look. I’ve got plenty 🎥

@EPICJONTUAZON 5 жыл бұрын

Will do man good luck!

@SpiritualChills Жыл бұрын

Red tsxx? NCOICEEEEE

@EPICJONTUAZON Жыл бұрын

🤘🤘🤘

@bobratu9029 3 жыл бұрын

you really don t have to remove the bumper.

@EPICJONTUAZON 3 жыл бұрын

I'd like to see that! Please make a video!

@jmartinez5463 5 жыл бұрын

I wang to change my HID without having to take off the whole bumper

@EPICJONTUAZON 5 жыл бұрын

I hope you have very small hands

@jmartinez5463 5 жыл бұрын

Why you say that ?

@EPICJONTUAZON 5 жыл бұрын

@@jmartinez5463 try and change it without taking off the bumper

@jmartinez5463 5 жыл бұрын

EpicJonTuazon i did it, it takes patience more than anything all I did was jack up the car take off the plastic and did what you did

@EPICJONTUAZON 5 жыл бұрын

@@jmartinez5463 ah I thought you were trying to replace the bulbs without taking the bumper off.

@nathanhale7444 4 ай бұрын

What a piece of crap! You shouldn't have to pull half the car apart just to replace a headlight bulb. It's a friend's car I'm reaserching installing new headlight housings but if it were my car it would be going up for sale as soon as the job was done.

@EPICJONTUAZON 4 ай бұрын

I'm sure there's another way to do it, I just know it will be a half measure with a higher risk of something else going wrong.

@nathanhale7444 4 ай бұрын

@@EPICJONTUAZON I've watched a couple other videos and they show the same thing. It's a great video. Very informative so please don't think I'm dissing your video. Just the car itself and acura for building such a pos. 👍

@EPICJONTUAZON 4 ай бұрын

It's all good I totally get it lol it's a PIA@@nathanhale7444