@sarai3055 Ай бұрын
I have a 10 lb Sledge with a 12-inch handle. Because of its mass you only have to take a small stroke to make the metal sing. Because it's the vibration that causes the separation of the parts. That comes from an auto mechanic who has been working on cars since 1963. And I love physics. Give it a try next time. Great video
@lukeallison9537 2 ай бұрын
Thanks for the video. I have tons of success with "Deep Creep" when i need a penetrating oil for auto work. Try that over wd-40.
@jtandrews3 2 ай бұрын
If I ever need a really potent penetrating oil, I'll mix 50/50 acetone and ATF. The problem is how to store it, and the fact that acetone and plastic doesn't get along very well.
@renegaderandle8728 2 ай бұрын
The neighbors are pissed!🤣🤣🤣💀
@BartSparrow123 2 ай бұрын
All that hammering to get it loose! This is why I'm soaking mine with PB Blaster all weekend and doing this on Monday!
@joshsnyyper 11 ай бұрын
Anyone got the BPM on the mallet strikes? 😂
@jtandrews3 11 ай бұрын
about 240
@joshsnyyper 11 ай бұрын
@@jtandrews3😂😂😂
@beammeupscottsp7952 6 ай бұрын
Next challenge: Rearward front lower control arms, haven’t seen anyone complete that task with just jacks!
@diegosantos8324 5 ай бұрын
You don’t have to drop the subframe far at all the which ever side your taking off take off just that bracket and use a pry bar while getting the bolt out
@BartSparrow123 2 ай бұрын
@@diegosantos8324 Thanks for the tip! So you didn't even need to lossen the front sub frame bolts up by the radiator or the exhaust hanger?
@diegosantos8324 2 ай бұрын
@@BartSparrow123yes just do one side at a time this avoids locking the steering wheel down and taking off the steering shaft the only downside to this method you won’t be able to torque the bushing down to spec
@BartSparrow123 Ай бұрын
@@diegosantos8324 I'm not worrying about taking the steering shaft loose, I have done that before and found if you use a grease pen to mark both sides of the shaft before you separate it, you don't even have to worry about keeping the steering wheel locked straight for reassembly. Thanks for the advice. I'm working on this today.
@dantonjorge1010 Ай бұрын
Mine only got out with the ball joint bushing, I had to buy a new bushing, the old one was really stuck
@kimandrews2693 11 ай бұрын
Great job! 👍
@itisallaboutspeed 10 ай бұрын
Thanks dude !
@beammeupscottsp7952 6 ай бұрын
Yeah I’m no mechanic but did all the upper control arms, Sway bars, struts, and engine mounts. The lower control arms were a no go, took that straight to the shop before I was left stranded 😂
@BartSparrow123 2 ай бұрын
It's not that bad, $20 for a tool and a $6 can of penetrating oil and you could have saved yourself $600.
@folabiolat9744 11 ай бұрын
He should have used the tool from the beginning.
@sirdizziebone 7 ай бұрын
Should have used an air chisel and had it out in like 2 seconds
@jtandrews3 7 ай бұрын
I don't have an air hammer worthy of that task. I'm sure Eric O's "big nasty" would have taken care of it in no time.
@sirdizziebone 7 ай бұрын
@@jtandrews3 I just used a cheap one from harbor freight and worked fine
@tonycervantes4816 4 ай бұрын
Is to much 150 foot pounds bro of frame back bolt do 😊
Sergio Outdoors
Рет қаралды 52 МЛН
1A Auto: Repair Tips & Secrets Only Mechanics Know
Рет қаралды 69 М.
Quick Front End Teardown - 2004 Subaru Forester - Strut, Hub, Control Arm, End Link, Tie Rod, Sanity
lifetimeofwork
Рет қаралды 698
FordTechMakuloco
Рет қаралды 58 М.
happywrenching
Рет қаралды 481 М.