This MDX cam in with multiple warning lights on due to a failed wheel speed sensor.Job turned ugly as the sensor was rusted into the knuckle. Ended up replacing the wheel bearing.
Пікірлер: 47
@unclemarksdiyauto Жыл бұрын
I hate when things don’t go as planned! You did good not panicking! Hope the customer understands. At least now, the car is working properly! Thanks for sharing your knowledge!
@Ricky-kp5ys Жыл бұрын
I love your process of approach thank you for sharing your experience
@advancedleveldiagnostics Жыл бұрын
Rust... Feel your pain, great job as usual!
@sbeezy562
Answer:Usually when this happen its telling you one of your brakes pads wearing out on one of the wheel brake system same thing happened to me on my mdx
@user-kn9px2br5v
Good work 👏
@ericsamara5097 Жыл бұрын
How do you go manually into the ABS.? I have a Launch x431 and I do not see that option available in my scanner
@jmbeltran8882
A have questions...why my Vsa is no show me in the dash when i push the botton
@onetruesoldiervt3686
Hello I have all the lights on except for engine light the sh-awd vsa and abs and triangle are all on is there anything I can begin doing first any help is greatly appreciated Ty
@martinarrieta248 Жыл бұрын
Grasias
@hanselldisla4643 Жыл бұрын
@phillip Bailey hello sir , I have a question my MDX turned all the same light you had on in your car . My question is the sensor you changed was the speed sensor ? And when the car was driving is was showing the speed you were on? Thank you.
@lashandramays3223
I have a 2012 Acura MDX when I drive my back wheel stop moving .. The VSA light is on..
@chevyman113121 күн бұрын
I have an 09 MDX, displaying SH-AWD, ABS and VSA on dash, no CEL. Question, what scan tool are you using? I either take it in or possibly see if I can get my hands on a better scan tool as the one I have does not dig in as deep as yours. Thanks
@chrisa.8175
I have that now 2010 acura zdx 9/6/2023. Going to dealer.. can i fix this without the dealer.. car drives perfect.. code states 6 cylinder failure but car runs great!! I am sick of of it.. this going to cost me ???
@chrisa.8175
Went to dealer, for same lights. And code status 6 cylinder failure.. but dealer service top techs could find NOTHING WRONG! but lights remained on when i drove 2010 acura zdx in. So it was lite up same 3 abs, emission, awd but car ran perfectly fine.. so i told tech what about speed sensor.. he said everything check out fine??? So 2 weeks later lights back on. Only when i back out slowly from garage. Intermittently happens after code is cleared.. but car runs fine!!! Could it be a wheel speed sensor??? How can i find out without code or Diy.. help
@footballfanz6
My 2010 Acura mdx sh AWD system back wheel is not working. Any idea on how to fix it. Thank you
@MrSamPhoenix
This is usually a bad battery or connection to it.
@abc666888Күн бұрын
it's speed sensor fault, but multi lights on including sh-awd. in this case , is it driving in awd mode or just front wheels?
@JoseDiaz-xc9xs Жыл бұрын
I think that is the last year of port injection. what a shame. at least toyota is offerring dual port and direct on most its new cars.
@Ken-1
could you not just cut out the bad section of the wire and splice in a new section of comparable gauge?
@azeemsiddiqui5178
Great info but my story is bit different but I got exactly same three lights and messages shown in video.