If you don't remove the crankshaft pulley and only had to do some work on the cams, do you still need to do anything to set the timing on the bottom end besides put in the one tool to hold the crankshaft at TDC? I'm assuming you can just use the tools on the top-end to set the cams and phases and then slip the belt back on?
@antonioaguirre6166 Жыл бұрын
If you locked the crankshaft and do not remove the pulley it will be ok. The pulley has the engine timing and the ignition timing too.
@emilyhofland8219 Жыл бұрын
Don't listen to him. The bottom crank is not keyed, or marked. You need to treat this engine like you are doing a full timing job. If you don't lock that crank, it will move, a lot.
@antonioaguirre6166 Жыл бұрын
@@emilyhofland8219 this might help kzfaq.infoxCQ6crfTJt8?feature=share
@soyinkakorede8679 Жыл бұрын
What is the work of that small special bolt
@antonioaguirre6166 Жыл бұрын
It holds the crankshaft at TDC there’s another tool that goes on the pulley too to set the ignition timing. I will recomen you to get it too. I didn’t used it cuz I had a mark on my harmonic balancer
@mohammadridzuanmddaud1814 Жыл бұрын
Hi sir, is it neccessary to lock the flywheel when tightening the crank bolt?
@antonioaguirre6166 Жыл бұрын
Yes. Very
@antonioaguirre6166 Жыл бұрын
kzfaq.infoxCQ6crfTJt8?feature=share
@antonioaguirre6166 Жыл бұрын
Maybe this might help
@mohammadridzuanmddaud1814 Жыл бұрын
@@antonioaguirre6166 tq so much sir
@em8819 Жыл бұрын
What size socket for the crankshaft bolt? Thanks
@antonioaguirre6166 Жыл бұрын
I couldn’t get to you sooner. I don’t remember from the top of my head I want to said is a 10 mil or 11 mil. I’ll be at the shop tomorrow and will tell you for sure the exact size
@em8819 Жыл бұрын
Ok thanks👍
@antonioaguirre6166 Жыл бұрын
It’s 10 mil
@antonioaguirre6166 Жыл бұрын
@@em8819 I made a short for you. Maybe this will help you kzfaq.infoxCQ6crfTJt8?feature=share
@antonioaguirre6166 Жыл бұрын
@@em8819 I try to do it under one minute
@user-vi4xt9ou6u4 ай бұрын
How can I set the crankshaft pulley
@antonioaguirre61664 ай бұрын
kzfaq.infoGUi6ZF74TiQ?si=oyrKpE5kqGq2aeMN
@antonioaguirre61664 ай бұрын
try this
@antonioaguirre61664 ай бұрын
kzfaq.infoxCQ6crfTJt8?si=2Ezndafn6zQahzli
@antonioaguirre61664 ай бұрын
i hope this helps
@user-ph4lf4dr6n Жыл бұрын
Tengo uno en tienpo pero no prende pero si si lo adelanto prede
@antonioaguirre6166 Жыл бұрын
Usaste la herramienta para ponerlo a tiempo o así al ojo lo pusiste a tiempo en la polea.
@antonioaguirre6166 Жыл бұрын
La polea tiene los dos tiempos el timing belt y el ignition timing