2014 Jeep Cherokee Driveshaft Replacement

No video

2014 Jeep Cherokee Driveshaft Replacement

Рет қаралды 2,298

Күн бұрын

Today Laura shows Step-by-Step How to Replace a Driveshaft on a 2014 Jeep Cherokee. Thanks for Watching! Subscribe, Like & Share! We Appreciate Your Support!
DRIVESHAFT PART USED IN THIS VIDEO:
www.summitraci...
TOOLS & PRODUCTS USED IN THIS VIDEO:
www.amazon.com...
Freedom Wholesale, llc..
WEBSITE: ridefreedomms....
FACEBOOK: / freedomwhole. .
INSTAGRAM: / freedomwholesal. .
TOOLS NEEDED
Socket Wrench & Power Wrench & Extensions (8mm 10mm 12mm 13mm socket) (T45 torx bit)
Large Pry Bar & Mallet
TIMESTAMPS
0:00 - Intro
0:13 - Before Getting Started
1:45 - Driveshaft Removal
7:17 - New Driveshaft Install
9:59 - Skid Plate Install
13:13 - Outro
DISCLAIMER OF LIABILITY:
HopFam Media, hereinafter referred to as (HFM) specifically DISCLAIMS LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES and assumes no responsibility or liability for any loss or damage suffered by any person as a result of the use or misuse of any of the information or content in this video. HFM recommends safe practices with Common Sense when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, and/or any other tools or equipment seen or implied in this video. HFM assumes and/or undertakes NO LIABILITY for any loss or damage suffered as a result of the use, misuse or reliance on the information and content of this video. USE AT YOUR OWN RISK: This video is for entertainment and/or informational purposes only. It is your responsibility to evaluate for your own safety and physical condition, or that of your associates, and to independently determine whether to perform, use, or adapt any of the information and/or content of this video. Any automotive repair and/or modification may result in an injury. By voluntarily undertaking any task displayed in this video, you assume the risk of any resulting injury; your safety is the sole responsibility of the user and not HFM
2014 Jeep Cherokee, driveshaft, drivetrain, replacement, reconditioning, do it yourself, method, process, repair, used auto, used car, car dealer, car dealership, used car dealership, car maintenance, auto mechanic

Пікірлер: 18

@clschuster25 2 ай бұрын

Thank you for doing this video. I may be doing this on my 2016 2.4L Latitude soon.

@fordmuscleluis9710 4 ай бұрын

Glad you got the new driveshaft replacement for this Jeep phenomenal job

@hopfammedia 4 ай бұрын

Thank you @fordmuscleluis9710. Sure do appreciate your encouragement!

@maxrfinch 2 ай бұрын

6:38 I’ve never heard of the transfer case loosening on these. Do you remember where it was loose and what needed to be tightened?

@hopfammedia 2 ай бұрын

Hi @maxrfinch. Each bolt that fastens the chunk was finger tight. It's as if someone inspected, then slightly put it back expecting to finish up later.

@JohnnyAnderson1 4 ай бұрын

Just did this on a 2012 Grand Cherokee last week.... Didn't realize there were 100 different driveshaft length options and no one had the correct length I needed lol

@hopfammedia 4 ай бұрын

Whoa... where did you finally come across the right one?

@JohnnyAnderson1 4 ай бұрын

@@hopfammedia it's still sitting in my yard.

@hopfammedia 4 ай бұрын

So, your still seeking a replacement?

@hopfammedia 4 ай бұрын

Ours was sourced at Summit Racing. Fortunately, we did not run into a choice on lengths. Their system chose it for us based On Year, Make, Model, Engine, Drivetrain/4wd. Hope this helps!

@JoSh-oo-Ah 4 ай бұрын

Cool and awesome!!! 😊❤ #AwesomeExperience

@hopfammedia 4 ай бұрын

Thanks JoSh-oo-Ah!

@SuperMAZ007 4 ай бұрын

Some BMW have the same setup as seen in the videos.. Also kind of stupid that you have to replace the entire driveshaft just for that one leaking o-ring. I'm glad you got it out, some car manufacturers make it so crammed that you need also to take the exhaust off. Not a huge deal with a new car but a when it's all rusted it's not so pleasant. Well done you all.

@hopfammedia 4 ай бұрын

Thank you @SuperMAZ006. The planned obsolescence for future repairs is something to behold. Thanks for posting!

@joshtamang-mo3jg 3 ай бұрын

Good job. Just curious how much to replace it ?

@hopfammedia 3 ай бұрын

Thanks @joshtamang-mo3jg! The shaft (link in the description) cost us a little over $500

@spasticslug2932 3 ай бұрын

You lost points with me when you said you don't have a torque wrench and you're doing it by "muscle memory". You don't 3/8" inch-lb torque wrench? Sure you can feel when the bolt is snugging up, but I've yet to find a mechanic who gets the torque anywhere close doing it by feel.

@hopfammedia 3 ай бұрын

Ok... Good to know! We have torque wrenches for the heavy stuff, just not a good one for the light stuff. Appreciate your post!