No video
2016 Mazda3 Front Brakes Replacement - How To
Рет қаралды 71,139
Күн бұрынThis video shows the process of replacing the front brakes on a 2016 Mazda3 Grand Touring.
Parts Needed:
- New brake pads
- New brake rotors (if needed)
- Anti-seize (optional but preferred)
Tools Needed:
- Socket wrench
- Sockets (13mm, 17mm, and 21mm or lug wrench)
- Flat head screwdriver
- C-clamp (for compressing brake piston)
- Floor jack
- Jack stands
- Breaker bar or pipe (recommended)
There you have it! Feel free to comment any questions and we will be sure to provide any suggestions we may have!
DISCLAIMER
This video is intended for informational and entertainment purposes only. All repairs should be handled by a licensed professional. We, steveandthemilkman, are not responsible or liable for any damages, loss, or injuries that may result from or be related to the use of any methods or equipment shown in this video. We do not guarantee that the content of this video is complete or accurate. Any damages, loss, or injuries that may occur due to the use of any equipment or information provided in this video are the responsibility of the user only. This disclaimer supersedes any content of this video.
@KiLLeRBison1 4 жыл бұрын
This is hands down the best beginner breakdown of how to replace brakes that I've ever seen. I work with legitimate engineers who don't even come close to this level of understanding and documentation. Stellar job guys.
@dougswanson2563 4 жыл бұрын
Nice demo. When pushing in the piston I usually use the old brake pad in front of the piston so I don't push on one edge of the piston and/or damage it
@bearjo11 3 жыл бұрын
Nice!!
@TLEE68 2 жыл бұрын
I’d also suggest you open up brake fluid reservoir cap when pushing the piston back to ease pressure in current extruded position.
@user-mh7ot4ef2i 13 күн бұрын
Eine der besten Erklärungen, kompetent und sachlich. Auch ohne den Text komplett zu verstehen - sehr hilfreich.
@GeeWrong 23 күн бұрын
Dude this tutorial is fuego. Appreciate you for going into deep detail & considerations. Answering questions that we aren't even thinking sometimes.
@Dan27894 4 жыл бұрын
Thanks for making this video, super helpful! People like you are what make DIY maintenance achievable for everyone!
@steveandthemilkman1311 4 жыл бұрын
No problem! We're glad it's useful for you. That's our goal, we want to show that jobs like this are completely doable for most people. It's great that you can save a lot of money and build up a collection of tools and skills at the same time.
@boxofknives 3 ай бұрын
I haven't changed brakes in years, and this is exactly what I needed for a refresher on my 3, thank you!
@brandone7273 2 жыл бұрын
This was awesome, thank you so much. I've been putting off changing my rotors for months and this video made it a very easy process. Took maybe 1 1/2 on the first side while I went back and forth looking for tools and jumping around this video; by the time I was done with the first side I felt like a pro and had the other side done in 20-30 minutes. This was an excellent tutorial; thank you!
@thisisudax 2 жыл бұрын
Extremely helpful video for a beginner like myself. I just did all 4 brake rotors and pads thanks to your video and a few others. I appreciate all the detail you went into of why you should be doing the steps you demonstrated. That’s often neglected.
@SlowCarsFastSFV 2 жыл бұрын
Thanks for posting this. As someone already stated you should keep the anti rattle shim with the slits in it from the original pads. The hardware kit to replace them on my 2018 3 Grand Touring Mex is BJY7-33-29Z. A shop threw mine out and I had to replace them.
@considertheravens7100 3 жыл бұрын
I like to put the old shoe on the Piston before tightening with the c-clamp to even out the pressure
@danield9375 9 ай бұрын
Very descriptive video. Great for beginners. Removing the rotors was the scourge of my existence. Ended up purchasing a gear puller to take them off. Also, I think you should insert the pads from the outside of the hardware, instead of the inside. Made it much easier to avoid touching the front. Also didn't have to fight with the hardware to get them in. I believe they are designed to be inserted in this direction.
@dnope6453 4 жыл бұрын
Man thank you. Finally a clear and useful video.
@steveandthemilkman1311 4 жыл бұрын
You're welcome! We're glad it was useful to you.
@Jedislayer19 3 жыл бұрын
thank you so much for making this tutorial. I'm going to try my best to change my brake pads/rotors ASAP.
@pathingmusic 2 жыл бұрын
Wish I saw this before I ran into the annoying hardware following a different tutorial… great info and thanks for putting it out there!
@ap4098 2 жыл бұрын
The anti rattle shims that you disgarded from the original pads should be retained. The brakes will still stop the car without but are designed to work with with them. My local tyre/brake centre did the same on my car and I noticed a slight rattle afterwards when driving on uneven surfaces or raised manholes. At first I thought it was a worn link arm bush but only after I took it in for a Mazda service did they spot the missing shims. That cost £67 just in parts and I fitted them myself. Now no rattle.
@Knightlore10 3 жыл бұрын
Recently bought a 2017 Mazda 3 so if you still have this car, your maintenance videos are going to be a great reference. I cant see that anyone has done underbody rust treatment on this model so I'd love to see a comprehensive video on that. My own channel is dedicated to motorcycles but you never know....;-)
@saga2760 3 жыл бұрын
I also have the same year and model and getting ready to change front and rear brakes and rotors. Be aware that if your Mazda has electronic parking brake you MOST put the parking brake in service mode and push the rear caliper instead of rotating it. Lots of people are braking the motor in the intent of push and rotate piston. KZfaq has some videos about this procedure just search “ how to put Mazda electronic brakes in service mode.
@mattmgarza 6 ай бұрын
If you are going to replace the rotor, there's no need to worry about damaging it with the hammer and therefore protecting it with wood like that---just some info for anyone interested. This is a great video.
@michaelmcleary8566 3 ай бұрын
Assuming that the new rotors are ok. I have had a warped brand new disc in the past but I was able to use the old one till I could get the warped disc exchanged.
@poopman99 Ай бұрын
Yeah easy to find a piece of wood just in case. If there is an issue you can still use the old rotor.
@kevinandrews2584 Жыл бұрын
Very nice video. Thank you! Was looking for the future when replacing my brakes for my Mazda. Mine is a 2017 grand touring with 23k miles on it. Eventually I'll get those type of rotors with the drilled holes in them to replace mine. So much cheaper to do stuff like that yourself then paying a shop to do it for you
@josephcarrillo2247 4 жыл бұрын
Awesome DIY ! Now I'm ready to work on mine. Thanks!
@steveandthemilkman1311 4 жыл бұрын
Thank you! Glad we could help.
@GoodMenstruationAttitude Жыл бұрын
This is amazingly detailed! please do every other possible driveway job next ;)
@ralgc 2 жыл бұрын
This video was awesome and doing it myself saved me a lot of money. Great tutoral video. I did it step my step following your video and it was a lot easier the other side. 🤘🏽👍🏾
@retro8919 11 ай бұрын
Awesome video, will come in handy this weekend
@IsleofMoto 2 ай бұрын
Great tutorial. Thanks for taking the time to share!!👍🍻
@geoffgorlick790 2 жыл бұрын
Awesome demonstration. Torque settings would make it perfect 👌👍
@ganonjesuschrist2053 2 жыл бұрын
Thanks for the video. Great learning experience. I ha ld to make sure to get the correct lubricant for the caliper pins, back of pads. Etc.
@bluesbrother2383 4 ай бұрын
Always make sure you dont damage the rotors that are getting thrown in the garbage anyway
@mikej791 3 жыл бұрын
Thank you so much for the help, saved me a lot of time and pain!
@steveandthemilkman1311 3 жыл бұрын
No problem.. Thanks for watching!
@billjames3030 2 жыл бұрын
@@steveandthemilkman1311Nice video. What brand pads did you use ?
@eskeskeskeres 2 жыл бұрын
you forgot to mention to release brake fluid cap before brake replacement. (when you push brake piston, brake level increase).
@matthomer1224 2 жыл бұрын
Nice, easy to follow video, very informative. Just doing mine, and my discs are stuck like a limpet. Got a 3 legged puller on them, but they're not shifting. Me thinks it's hammer time.
@ianjarvis9511 4 ай бұрын
Good stuff. i'f only napa gave me the right size caliper and rotor
@robtk3 3 ай бұрын
Well, the incorrect parts are usually less expensive so... 😏
@SureshPatel-em5tf 2 ай бұрын
Nicely explained
@doncarr128 3 жыл бұрын
Thank you so much for this mate !
@longher3138 3 жыл бұрын
Thanks for the informational video! Gonna change my brake pads and rotors this weekend. I may have missed it in the video but what are the torque specs on the bolts? Thanks in advance.
@peternorth2209 9 ай бұрын
Wouldn't recommend the red thread locker, with the proper torque applied to the bolts plus amount of heat generated by the brakes, it's highly unlikely the bolts will come lose. Use the temp thread locker (blue) instead of red if you want that added security, the red is just setting you up for headaches down the line.
@PBS-nm1uu Жыл бұрын
this is a great video, thanks
@abbas1872 3 жыл бұрын
Your old pads were pretty stuck because of the rust that had formed behind the hardware. If you put some anti seize on the hardware area prior to putting on the hardware this will prevent rust from forming and help keep your pads moving freely.
@kenkyuen 4 жыл бұрын
Use the old brake pad to help compress the piston. It will help compress it evenly. Also I would recommend putting some antiseize on the brake hardware where the pads and the hardware meet. Not using antiseize is why removing your pads were so difficult.
@steveandthemilkman1311 4 жыл бұрын
Thanks for the tricks. We love little technique that make things go smoother for the job and future jobs.
@eskeskeskeres 2 жыл бұрын
small metal plates released from original brake pads. Not needed to put them on new pads, please?
@intimidatorno3ca 3 жыл бұрын
This video is going to be a huge help. My 2015 is due in all 4 corners and I'm upgrading to the PowerStop Z23 Evolution kit. I presume doing the rear brakes will be a similar process.
@steveandthemilkman1311 3 жыл бұрын
We're glad to hear it! The rear should be very similar.
@intimidatorno3ca 3 жыл бұрын
@@steveandthemilkman1311 and it was. Did the job last weekend. The new stuff feels pretty good. Now to address the rusty parking brake mechanisms on the calipers. Which are apparently a weak point.
@Zadesniper 2 жыл бұрын
@@intimidatorno3ca Did you ever do that? I'm do for mine
@intimidatorno3ca 2 жыл бұрын
@@Zadesniper I did. Last November. Went pretty well. Needed a tool to spin back the rear caliper pistons. The one I picked up was a cube with different pin arrangements on each face. Besides that virtually the same. Also found the Mazda service manual that walked through the process with torque specs and where to apply thread locker. Parking brake still not addressed.
@TLEE68 2 жыл бұрын
Qq-no brake grease required on the brake pad end tips where it contacts the stainless steel shim clips?
@gurgenmakaryan4428 2 жыл бұрын
Amazing review!👌
@johnrogers2826 3 жыл бұрын
Really good video! Clear, concise, easy to follow. Thanks, you just saved me about $250! I'm subbed!
@steveandthemilkman1311 3 жыл бұрын
Thank you! We are very glad to hear it helped.
@greg2142 2 жыл бұрын
Great video although I'm not sure putting anti-seize on the studs is a good idea.
@michaelop757 3 жыл бұрын
Great video
@steveandthemilkman1311 3 жыл бұрын
Thank you for watching!
@Mr.Be93 Ай бұрын
Powerstop kit? I just installed this yesterday. Great video.
@alexm2404 3 жыл бұрын
IMPORTANT! Just to be aware that the lower sliding pin has a rubber sleeve on the it. Usually this pin will get stuck. Make sure you buy a replacement kit or a new rubber sleeve because in time this rubber sleeve will increase in volume and will get the pin stuck. Once you change the rubber sleeve, make sure you use a silicone based lubricant and not petroleum based grease/lubricant. Petroleum grease will lead to rubber sleeve to swell and the pin will get stuck, your pads and rotors might heat up and will wear down unevenly. Some people remove the rubber sleeve and reinstall it without it. Not sure why calipers are over engineered. Some say it's to reduce brake vibration but I'm not sure if this is noticeable or not. If there is anyone out there with more knowledge on this particular matter, please let us know.
@talon7691 2 жыл бұрын
What is that part called ?
@alexm2404 2 жыл бұрын
@@talon7691 the sleeve?
@talon7691 2 жыл бұрын
@@alexm2404 Yes does it have a part number or a more exact name? Thank you!
@alexm2404 2 жыл бұрын
@@talon7691 don't know how is called, but you can find it if you look for the caliper repair kit.
@alexm2404 2 жыл бұрын
@@talon7691 BRAKE CALIPER SLIDER PINS GUIDE KIT
@MillHouseUSA 2 жыл бұрын
Do you have the Torque specs for the rotor bolts.
@Grynjolf Жыл бұрын
Man, my rotor is stuck on even after beating it with a hammer. Any tips?
@gailgutierrez9118 3 жыл бұрын
Awesome DIY, thank you. Please me, Numbers of parts used: pin boots, discs and pads?.
@xCALHOUNx1 2 жыл бұрын
Always a great reference when I do my 2015! How did you get the pads in so easily?? It always takes me 30 minutes or more to get the pads in with the hardware!
@pathingmusic 2 жыл бұрын
The brake pad hardware makes me annoyed with how much fiddling i have to do just to seat them. Everything else is no problemo
@Mxfra Жыл бұрын
What’s the torque spec mate on the bolts mate?
@Warmsunset26 2 жыл бұрын
Hello. Thank you for your sharing . Could you please tell me what SIZE your cup oil filter wrench is that you are using ?
@DavidTO.22 3 жыл бұрын
I have a 2018 Mazda 3 GT with the e-brake. Is changing the rear brakes the same procedure? Is there anything to be aware about the e-brake?
@steveandthemilkman1311 3 жыл бұрын
I am not sure as our vehicle doesn't have the electric parking brake. Sorry we couldn't help.
@w0nder_what Жыл бұрын
Question - I know my brakes need replacing but I don't know how to figure out if its the front or the back brakes?
@naturesbless 4 жыл бұрын
Would you ever do a video on replacing rear shocks? Can't find any videos on it!
@steveandthemilkman1311 4 жыл бұрын
Absolutely! We would like to do this soon on the 2016.
@naturesbless 4 жыл бұрын
@@steveandthemilkman1311 I just did mine on the 2015,I definitely should've removed the coil; hope you guys go through it because I didn't feel safe doing it lol Keeping it jacked up and doing the lower nut first was a huge help.
@Warmsunset26 2 жыл бұрын
To get your piston to go back inside, how do you do that with the ' electrical braking system ' that is now being placed on all Mazdas ? As mine is a 2018 Mazda 3 model.
@the_patdeezy 3 жыл бұрын
Awesome video! Where did you get the rubber sleeves that goes over the bolt ~5:58. Thanks!
@simondixon1202 3 жыл бұрын
Is there anything I need to do in regards the handbrake for front pads?
@courtneyvassell9278 3 жыл бұрын
And also when compressing the piston use one of the old pads so that there is equal distribution of force on the piston ....you could damage the piston lip the way you did it...but good overall vid
@davidpalmer4134 4 жыл бұрын
Torque specs? Thank you nice work.
@scheide717 4 жыл бұрын
Front Caliper Pins: 19-22 ft/lbs Front Caliper Bracket: 44-56 ft/lbs Wheel Lug Nuts: 80-90 ft/lbs If I googled that correctly...
@Dan27894 4 жыл бұрын
Samuel Scheide thanks!
@davidpalmer4134 4 жыл бұрын
@@scheide717 thx
@bilokenneth 3 жыл бұрын
No!!! Those information is wrong!! According to service manual page 2574, 2588, 2572, 2585: Front Caliper Pins: 20-22ft/lbs (Rear Caliper Pins: 17-19 ft/lbs) Front Caliper Bracket: 68-81 ft/lbs (Rear Caliper Bracket: 38-48 ft/lbs) You can check on owner's manual for Wheel Lug Nuts specs: Wheel Lug Nuts: 80-108 ft/lbs I hope you didn't torque the bracket with 44 ft/lbs only.....................
@1234oclock 2 жыл бұрын
Can anyone confirm what the actual torque specs are? I’m having trouble finding them
@motheolebelo 4 жыл бұрын
Good detailed useable video Thumbs up and thanks for sharing.
@steveandthemilkman1311 4 жыл бұрын
Thank you! Glad it was of use to you.
@zsalesz 3 жыл бұрын
Thanks for your help! What kind of grease do you use at 4:35?
@steveandthemilkman1311 3 жыл бұрын
That's Anti-Seize which isn't really a grease. It's used to prevent rust from sticking the rotor to the face of the wheel bearing.
@amazingridence3119 3 жыл бұрын
Is it necessary to bleed the brakes? Or does this small job just not require it, thanks! 🙂
@steveandthemilkman1311 3 жыл бұрын
Bleeding should not be needed. You only need to bleed the brakes if air made it into the lines and that shouldn't happen when doing a brake pad replacement since you aren't actually opening the system at all.
@haroldmarquez2665 2 жыл бұрын
Where did you get those drilled slotted rotors ?
@dartu5854 3 жыл бұрын
Do you have one for the rear? Not sure what to do with the electronic brake on it.
@steveandthemilkman1311 3 жыл бұрын
We don't have a video for the rear yet. Unfortunately, if we make one for the rear it will not be on a car with the electric parking brake. I recommend checking some forums to learn the differences in the process. Good luck!
@pavlidisification 2 жыл бұрын
Thank you very much Master! Your video helped me a lot.
@bastogne315 Ай бұрын
Cant shift those bolts. State of my slider pins. Full of rust.
@htetaungnainglynn7500 5 ай бұрын
I am struggling to push the piston back in. I used a piston compression tool but the piston resists. Any suggestion?
@nrich5127 4 ай бұрын
Temporarily remove your brake fluid reservoir cap in the engine compartment.
@nrich5127 4 ай бұрын
* Warning * - I came across this warning and took note of it on my computer. I don't know if it's verified as I'm not an engineer BUT since the "fix" is so easy to perform vs the potential damage , I will do it without hesitation. * * * Before doing replacing brake pads read this: Due to ABS System , before you compress the piston in the caliper you must open the bleed valve ( attach a plastic hose to a bottle ) . If you don't do this and compress the piston in the caliper , you can send back pressure and damage the ABS control module. The average cost for an ABS Control Module Replacement is between $980 and $1,038. Labor costs are estimated between $107 and $135 while parts are priced between $873 and $903. This range does not include taxes and fees, and does not factor in your unique location. Related repairs may also be needed. Do you really want to take a chance ?
@andrejcollak9347 3 жыл бұрын
Great video thanks made in China brakes and Red corrosion not nice
@TLEE68 2 жыл бұрын
How many ft lbs torque on the caliper bracket and slider bolts and is that spec good for all 3rd gen mazda 3?
@keithschmidt2961 Жыл бұрын
75 ft lbs on the big bolts and 24 on the small bolts
@jamesrichardson771 Жыл бұрын
As much as I believe in antiseize" 💥 I wouldn't put antiseize on the studs if I were you !!! 😵
@nrich5127 4 ай бұрын
I haven't encountered any issues but I highly recommend you use a torque wrench to tighten lug bolts to spec.
@davidchin2497 3 жыл бұрын
Hello, Where can i get the anti rattle clips?
@steveandthemilkman1311 3 жыл бұрын
I would try Rock Auto.
@steveandthemilkman1311 3 жыл бұрын
But lots of pads come with them.
@davidchin2497 3 жыл бұрын
@@steveandthemilkman1311 thank you so much!
@bastogne315 9 ай бұрын
Pushing the piston in can be a c unt!
@grecotorrealba7851 3 жыл бұрын
S Touring Japonés o Mexicano?... hay diferencia en el N° de parte.
@steveandthemilkman1311 3 жыл бұрын
I am not sure if the parts are the same between Japan and Mexico variants. Type your exact VIN into a parts supplier to be sure you get the correct part.
@209euro2 Жыл бұрын
Tip: wear nitrile gloves if you’re worried about oils getting on the brake system.
@mrsassypants8218 3 жыл бұрын
I’m a female and I’m about to do this on my own watching this tutorial (wish me luck) 😂
@smellthecoffee5314 2 жыл бұрын
How did you get on Sassy ? I'm doing this tomorrow - don't expect any issues but you can never be sure :)
@onyachamp 3 жыл бұрын
Mountain dew!!!!! ewwwwwwww I'll take the crab juice
@sts6055 Ай бұрын
Your hubs is new and shiny, your disks ands are god. So replacement seems unnecessary.
@courtneyvassell9278 3 жыл бұрын
Nice vid...but u didn't see you bleed the system
@steveandthemilkman1311 3 жыл бұрын
Thank you! There is no need to bleed the system unless air makes it's way in. That should not happen in a routine pad replacement.
@courtneyvassell9278 3 жыл бұрын
@@steveandthemilkman1311 you arewelcome bro. I did my 2016 Mazda 2 disc pads just two weeks back I must say it was easier than changing my wife's 2011 Nissan Bluebird
1A Auto: Repair Tips & Secrets Only Mechanics Know
Рет қаралды 4,4 МЛН
1A Auto: Repair Tips & Secrets Only Mechanics Know
Рет қаралды 118 М.