You asked - we delivered. Brock continues Episode 7 with a shootout between the Brock’s Performance Stage 1 ECU flash and Power Commander PCV (tested in E7 P1) vs. that exact PCV map imported directly into Gixzilla’s ECU because the Internet says, “That’s what you do!” Brock goes through his typical painstaking detail to keep the results as nonbiased as possible, while showing his tuning steps along the way. Is the Internet correct? Do we live in a ‘drag/drop/you’re done’ world? Check out Episode 7 (Part 2) - ECU Flashing (ECU vs. PCV Fuel Tuning Shootout) now.
The details :
Bike: Brock’s Performance 2017 GSX-R1000L7 Standard model (not the ‘R’ version) purchased from Fun For All Motorsports in Elizabethtown, KY
Exhaust: Brock’s Performance Alien Head 2™ full stainless exhaust system
Traction control: Motion Track Traction Control Standard (TC=OFF during testing)
Suzuki Drive Mode Selector (S-DMS): Power Mode=A (max power selected during testing)
Fuel used during test: 89 Octane Shell
Rear tire: Stock Bridgestone Battlax RS10 190/55/ZR17 - 35 PSI Nitrogen
Motor oil: Alisyn Pro Drive 21 Less than 0W (full synthetic)
Additive: Petron Plus 4-Cycle Lube
Air filter: Sprint Filter P08 F1-85 (see this link for detailed information: goo.gl/zgBcZG )
PAIR: Blocked
Power Commander: PCV with Brock’s Performance Track Map 1 or Zero Map, per video requirements
ECU: Modified, per video requirements (see this link for detailed information: goo.gl/TLKbvk )
FlashTune Quick Shifter / Auto Blipper Retrofit Kit GSX-R1000 (2017) (See this link for detailed information: goo.gl/KTcL6x )
5th gear pulls
Dynojet Model 250I dyno using DynoWare RT, Power Core C3 and WinPEP 8 dyno control - displaying the SAE scale (unless noted otherwise in video)
0:08 - Introduction / Where we left off
1:32 - Initial base run (Stage 1 ECU flash and PCV w/pump track map)
1:50 - Listing of current bike mods / Set-up
2:28 - Discuss base run results / Chart (194.14 RWHP SAE scale)
2:48 - Comparison of 650ib’s 2017 BMW S1000RR vs 2017 GSX-R1K (Dyno chart URL below)
3:18 - Link added to 650ib’s S1000RR tuning video
4:10 - Acceleration discussion (*BMW has taller gearing)
5:20 - FTecu map import (PC fuel import)
6:03 - PCV map successfully imported into ECM
6:22 - Removing PCV from equation (install zero map)
7:13 - Dyno run (ECU w/imported PCV Map, no PCV)
7:42 - “Hey Brock… just import you PCV map and everything will be ROSES!”
7:52 - Discussing results from PCV import dyno run (25 HP HOLE!)
8:52 - Every single throttle position vs. RPM must be adjusted to do this right
10:25 - Using the dyno as a data logger
10:50 - Determining throttle position for changes
11:15 - Using analog input to see throttle position
11:45 - Kicking it old school (throttle stop)
12:22 - How do we fix the all of these problems?
12:48 - Using the FTECU unrestricted map (sw1 and sw2 switch selection)
13:43 - Dyno run (ECU w/FTECU unrestricted map, no PCV)
14:25 - Discussing results from dyno run
15:30 - Identifying and correcting lean/rich areas vs. RPM
15:50 - Increment adjustments to the fuel table (adjust number vs. percentage)
17:19 - Adjusting the fuel table at partial throttle
18:18 - Using throttle position sensor and throttle stop
19:16 - Spoiler! We already have the map done
19:52 - Dyno run (Brock FLASH ECU Stage 1-F with fuel tune)
20:27 - Discussing final results
21:18 - Final ECU tune vs. baseline chart (194.14 vs. 193.51 with ‘similar’ drivability)
21:59 - Advantages vs. Disadvantages (why Gixzilla will have stage 1 flash and PCV at the track)
23:15 - Where are we going next?
650Ib’s BMW S10000RR (2017) vs GSX-R1000 (2017) Dyno Chart URL: brocksperformance.com/content...
Brock FLASH ECU Stage 1-F with fuel tune: brocksperformance.com/brock-f...
Visit the ALL NEW www.BrocksPerformance.com - for additional information