Bro is it just me that nothing is easy these days on newer vehicles don’t get me wrong your video is great I have a 2019 king ranch and as you know it’s an expensive truck and all this cheap plastic and so many fragile plastic clips drive me crazy my last vehicle was a 2018 Honda Odyssey I’ll pop the hood on the upper left-hand corner passenger side you pop up to Clips One on each side and boom you take out the filter put it back in and your done …and again thanks for the video…

As a fellow KZfaqr, I want to thank you for putting this video up. Not that it was a hard job, but seeing it done by someone else, made it even easier. Thanks again.

Great video, save me about $150 from the dealer doing it! Maybe one thing…. For the folks that weren’t paying attention…. The filter should be put in such that the airflow indicator is pointing down. Thanks again!

Thank you, this video showed me the correct way to take this apart to change my cabin filter. Much appreciated.

Thanks so much. I just spent a half hour thinking I could just take the glove box off and bend the filter enough for it to slide in from below. Doesn't set flush doing that and finally I looked for your video. I buy the best replacement parts I can for my truck and do not want to spend cash on labor for such a little job. At least I thought it was simple until I tried doing it and really appreciate your money saving tips.

Great video with great step by step instructions. Saved me a lot of time by watching first before replacing my old stinky filter. And I agree with others who say Ford needs to make this a way easier process!!

NOTE: the airflow direction arrows point “down”. Take note of the orientation when removing and replacing. Looks like a cute symmetrical box, Not! Fins up, airflow down…you got this! Thanks for the video! What a bisch with out your helpful video

Thanks for this. I viewed another video and lowered the glove box also. This is so convoluted, it would be easy to break a tab if you are not careful. This helped a lot, I used a plastic kitchen tool as I do not have a trim remover.

Take the filter out and run the blower full blast on defrost, floor and vent while you spray Lysol disinfectant into the now empty air cavity, Then blow old filter off with compressor air gun and also remember to spray old or new filter with Lysol then re-install. The Lysol will help kill the odors in your duct work throughout the truck.

Thank you for saving me so much money by showing me how to do this! I appreciate this!

Good video. Be careful when you're dropping the glove box down. There's a little plastic arm assembly on the passenger door side of it that, as I found out, is fragile. There's a plastic gear inside a housing on the arm that makes the glove box open softly. I'm not sure if I broke it or if it happened with the previous owner. Fixed it wit JB Plastic Bonder.

Found this video at the perfect time. Good detailed explanation

Thank you for this video! Was able to do it right away after watching.

Just wanted to say thank you for the video. Just took a few minutes

Than you for making this video... they don't make it easy on us. It isn't that bad but it's just hard to know where this stuff is actually located at.

Awesome; couldn’t of done it without your video👍

Thank you for sharing your knowledge on this task.

Best tutoring video so far

Great information with the ratchet size and tips for slowly taking of the parts with those clips, I usually break one, didn’t this time.

Dude u save me today. Super easy after watching his video. Preciate it.

Thank you. Very helpful. Just what I needed

Done on purpose by Ford. Makes the average customer go to a dealer and pay big money!

Thanks man, helped me and I appreciate you taking the time to make the video.

Thanks for making a straightforward video!

Just what I was looking for.

Helpful additions would be starting with the needed tools, also the air flow direction just in case

i did my 2018 stx but it was almost the same. very good thanks

Perfect. Thanks!

thanks for the pointer on pulling the fascia off!

Thx. Saved me time. Much appreciated

This is the most asinine design I've seen of a filter yet.

Well thats why I broke a snap clip on the cabin air filter cover....I didn't do all this crap. Tried to slide it up in there and didn't work. Ridiculous!!!! Thanks for the video

Good straight forward video! thanks.

You should mention the Air Flow is from top to bottom and the arrow needs to be pointing down.

Great help. Thanks. What a f#@$ed up design.

Thanks for making this video

Great video! Just did it myself

Great tutorial. You should do one for the MAF sensor? I can’t find it and no one has any videos for it. I never had a truck before and it was right by the air filter on my fiesta. 👍

Very helpful, thank you!

Why does ford make everything so complicated compared to other manufacturers

Easy. Nice to see. Thank you.

New filter ordered, $15. Dealershp wanted $115 CAN for one.

excellent video, thanks man

Very helpful! Thanks for posting!

The dealership wants $85 to do this....filter Cost me $8 at O'Reilly's. Dealership rip off in Rio Rancho, NM

Thank you for this post - I sliced my finger open but got the job done. Ford lost points with me for this! Does the rubber panel piece fit looser after this process? (Also disappointing.)

Thanks for the video. Now, can you help me find my 7mm nut driver?

Looks like you have it in there upside down.

U didn't show the first clips of the filter door

Does this apply to the 2018 2.7 eco boost as well? Mechanic trying to tell me it’s under the front dash and would be over an hour to replace costing $75. Seems like bullshit.

Nope......this is a dealers job. My Camry is snap out, snap in. This is bullshit. You’ll have broken snaps, and have to replace the motor mounts !

thanks guy

Another dip sh@t Ford let's make it more complicated and get that $110 hour labor charge! Thanks for posting!

You forgot to show which side of the filter is up

You could just open up the glove box the rest of the way there is two tabs you push the glove box will open up and then you can get to the cabin air filter no need to go through all the steps takes like one minute

I will never buy a ford again