2023-2024 KTM HUSQVARNA GASGAS 125sx TC125 MC125 Top end replacement rebuild series part 1. TBI

Рет қаралды 6,001

Күн бұрын

Bare bones rough and dirty top end rebuild step by step on how I do top end rebuilds.
Join my Facebook group!!!
/ 709915283880183

Пікірлер: 35

@damienhasleby8390 9 ай бұрын

Cheers for going to the effort of filming and going into detail mate. Im pretty confident with engine work but am yet to pull my TC125 apart. Always little tricks and tips on new bikes.

@themotocrossmodchannelWulfMX 9 ай бұрын

If you disconnect the battery and don’t remove the pv servo unless you have to, it’s pretty straight forward. Part 2 soon!

@rowantrefz8906 9 ай бұрын

Nice step by step. I play it on 2x because I've pretty familiar. Suggestion: tripod to make your life easier.

@themotocrossmodchannelWulfMX 9 ай бұрын

I know!!! Lol

@paulgriffin7273 9 ай бұрын

If you pull the magneto cover off its way easier to turn the motor over.

@themotocrossmodchannelWulfMX 9 ай бұрын

This was done in the video

@onthethrottle7104 8 ай бұрын

7 hours and you're happy it looks good like it was a surprise? That should look perfect at 7 hours. Thanks for the vid though.

@themotocrossmodchannelWulfMX 8 ай бұрын

Yes, considering the carnage I have seen with the 125’s grenading with stock cast pistons under 7 hrs, cranks coming apart on break in rides, thermostats sticking and blowing the engines up, intermittent electrical issues that plague the ignition timing, (there was a recall for it), whereby peppering the piston top with detonation, the diff fuels and octane and premix this engine has seen, the dyno runs, the sand at Southwick up to the axles, the mud, the torture tests, yes I’m amazed that this engine has lasted and looked like it did. You obviously don’t own one of these and have no clue what these are like to own and work on, but yet comment as if you do. 🧌

@AD_Racing3 9 ай бұрын

I feel like if I try this my bike will never start again

@themotocrossmodchannelWulfMX 9 ай бұрын

That’s not true! You can do this with simple tools and patience!

@beckhambailey9348 8 ай бұрын

Austin

@AD_Racing3 8 ай бұрын

@@beckhambailey9348 hehe

@HibouRacing 2 ай бұрын

hi bud ! how are you nice vid here thanks! Can you show us how to rebuild the valve please? because since i have rebuild mine and reset it, FI blink 5 short times. The manual says that it's valve problem so it might be a mistake on the rebuild?

@themotocrossmodchannelWulfMX 2 ай бұрын

thats the PV fault code

@HibouRacing 2 ай бұрын

@@themotocrossmodchannelWulfMX sorry i mean 5 long blink

@nitro2772 5 ай бұрын

Petite question tu as remis un simple segment ou un double ?

@stevedouglas1654 9 ай бұрын

Yer thoughts on the TSP TBI Power Kit ( high compression head & ECU reflash ) ? 🤔

@themotocrossmodchannelWulfMX 9 ай бұрын

Who's TSP? 🤣

@themotocrossmodchannelWulfMX 9 ай бұрын

I don't have any info on their set up, I do know they make some great stuff.

@matth8924 3 ай бұрын

Do you really have to do this every ~10 hours? If I’m just a weekend warrior how many hours should I do on a piston before a rebuild?

@dailymx3865 4 ай бұрын

If I do a top end on a 23 ktm125 and leave that servo on do I need to have the power valve re synced ??

@themotocrossmodchannelWulfMX 4 ай бұрын

it should be ok, but take two min and reset it!

@happyman8488 9 ай бұрын

And they say 2 strokes are cheap. 275 hours of hard mx hours on my yz 450 after rebuild at 164 hours. Everything was in spec except cam chain little stretch.

@themotocrossmodchannelWulfMX 9 ай бұрын

Great news! Two strokes are cheaper however..less expensive to purchase outright, cheaper parts, etc..if the rod goes it locks up on a 2 stroke, it can still be pricey depending on what it takes out..if the rod goes or drops a valve on a 4 stroke, there is usually some large scale damage. My other 3 bikes I have are a 21' 250sxf, 23' 350sxf, and Rockstar FC450, so I am into both platforms. Glad you had good luck with your yzf, some have not.

@MxBikesVr 7 ай бұрын

How many hours should it be until I must replace the top end I’m at about 24 hours right now

@themotocrossmodchannelWulfMX 7 ай бұрын

Manual says 15 hrs, I would for sure do it soon to be sure and safe, use a Wossner 2 ringer forged part number 8174DA.

@MxBikesVr 7 ай бұрын

@@themotocrossmodchannelWulfMX thank you so much doing a replacement soon

@petermoygannon698 3 ай бұрын

Your changing the piston in 7 hrs . That seems early . My fc 17 450 150 hrs I done top end and now it's got 230 hrs .

@themotocrossmodchannelWulfMX 3 ай бұрын

4 strokes are obviously different, this is a test bike and has been subjected to testing and hard use..if you have a 23' + 125/250/300, you would know this was precautionary!

@AceOfSpadesPRO01 9 ай бұрын

Kinda sad to see 2 strokes going this direction. I just picked up a runout 2022 TC250 because I wanted a simple 2 stroke that’s easy to work on like they’ve always been. These things seem just as complicated to work on as a 4 stroke

@themotocrossmodchannelWulfMX 9 ай бұрын

The are diff that’s for sure. If you spend some time with them it’s not bad.

@Dat_Sun 9 ай бұрын

Any other tbi owners with scored piston? 9 hours 23 250xc is toast already. Cylinder damaged.

@themotocrossmodchannelWulfMX 9 ай бұрын

Yikes, there have been some, how bad is the damage? I have a new cyl in stock if you need one..email me if you do. JboneMotorworks@yahoo.com

@Lokis12-2 9 ай бұрын

Why so low on the hrs? Didn’t even make it to 10hrs

@themotocrossmodchannelWulfMX 9 ай бұрын

Wanted to make sure all was ok in there, also, due to all the carnage I have seen with cast pistons I decided to replace and do a video on a cast piston.