I just got my P1P after abandoning FDM for resin over a year ago. I am totally blown away by the improvements, ease of use and most of all SPEED!
@Another_opinion_ Жыл бұрын
And what about quality?
@WMBayouLures Жыл бұрын
@@Another_opinion_ So far its been amazing, I mean its FDM so it won't be as detailed as resin, but for FDM its great.
@joeturczak5656 Жыл бұрын
It's not an upgrade... It's a whole new ball game that others, including the God like Prusa, will have to play catch up and UPDATE their old technology to match this new bad boy on the block!
@redboom9874 Жыл бұрын
@@Another_opinion_ quality is really good at 200 outer and 300 inner walls while being at 10k accel.
@softfever5570 Жыл бұрын
As always, your review is truly objective. You have clearly done a lot of tests before this video. Which is rare among KZfaq reviewers nowadays. Well done!
@247printing Жыл бұрын
Thanks a lot, buddy! Keep it up with your Bambu Slicer forks - I am watching it :-)
@mpoxDE Жыл бұрын
Hurra! Great video, really enjoyed it - thanks for the shoutout! Always a big plus to learn something on the technical side, didn't know there is such a difference between P1P and X1C regarding electronics. My X1C just arrived, can't wait to check it out since I already liked the P1P a lot. Still using my MK3S+, though. I dont know why I sometimes chose it over the P1P, perhaps just because I'm so used to it. Time will tell if the Bambu printers work that good on the long run. Happy holidays und genieß deinen Weihnachtsschnaps, cheers :D
@247printing Жыл бұрын
Danke!! Glad to hear that you received your X1C - excited to see what you make out of it concerning content. I have to admit: I rarely use my MK3S+ since I have fast printers, but still for smaller parts or when time doesn't matter. HAPPY HOLIDAYS!
@hassosigbjoernson5738 Жыл бұрын
@@247printing Hallöchen! That raises the question: why does speed matter sooo much?! Most users should use their 3D printer as a hobby in the afternoon or at the weekends. And it should not matter to leave the printer printing (even over night) or 16hrs during day, especially since one printing hour does not cost so much (as Mpox video showed). And if I would run a small business, it would be an easy decision to invest in 3 printers (Ender3) and not rely on one expensive one (Bambu) for the same price and for reliability?! So: what is it with speed?! Compared to most Ender 3 variants and clones the P1P is 3-4x more expensive. And to add a important point to your conclusion: you not only learn much about 3D printing from a Prusa Kit, but also from a cheap printer like the Ender. Especially when considering adjustment, troubleshooting, settings in slicer (where BambuLab is limited) and of course modding. The adding of a Klipper solution to any Ender clone via Raspberry Pi, Notebook or Klipper "Pad" alone means ton of learning, understanding and Knoff Hoff. So again: why are people willing to invest like 3 times the money (compared to other basic printers often recommended) to get more speed for a hobby and experience less learnings, less tinkering time and at the end: less time with that hobby? If I "just wanted the 3D printed part" I could also order it at so many manufacturing services out there, without the need of a 3D printer in the first place (to give an extreme example of not being interested in the "how" but only the result). This could be an interesting question to answer, especially with having read so much comments under 3D printer reviews ... like you maybe have read. Grüße!
@J00LZ49 Жыл бұрын
@@hassosigbjoernson5738from a business standpoint, space is almost always an issue, being able to replace 3 or 4 printers with a single one means that you can either scale up further with the same space or that you need less space for the same print throughput. Also power consumption of running 3-4 machines compared to running only one is also a consideration especially as most of the power use comes from the bed heating and nozzle heating and that is what you are multiplying by having more machines to do the same amount of work. For hobby use, if you are prototyping and want to test parts it speeds up the process a lot being able to quickly print the parts. A lot of the time I am building things, designing and printing parts as I go. Being able to quickly print parts on my voron allows me to continue with the project rather than having to wait for parts to print before moving onto the next part. The difference here between a print that only takes an hour compared to one that takes 4 allows me to do so much more in one day rather than have to wait and put things off to the next day. Obviously when I don’t need it printed fast, I can just up the quality and have a longer print time if I am printing in the evening and will be at work the next day it doesn’t matter if it takes 12+ hours, but when I come home and want to get on with building stuff that evening being able to design, print and implement a part all in one evening is invaluable when you don’t have infinite free time. There is also the issue that the longer a print takes the more likelihood there is for a failure. Some of this is just due to print distance, but also time is a factor and increases the likelihood of electronic failure, power problems or temperature fluctuations. Failing a 16hour print puts you a lot further behind than failing it if it only takes 4.
@blakemoody5866 Жыл бұрын
Prusa will need to step things up a lot in order to compete. I feel like bambu is going to release a large format that will put the XL to shame as well. Would love to see a smaller bambu as well for more budget and stability
@C4CH3S Жыл бұрын
the bambu printer might as well be a smartphone. there are barely any parts for sale and everything is closed off so you can't even fix it with parts from third parties. the people actually running proper print farms will stick to prusa because at least you can buy replacement anything for them directly from the manufacturer. anyone replacing their farm with bambu printers is a fucking idiot, and will pay the price when they start breaking due to natural wear and bambu wants to either get it back for service all the way in china, sell expensive parts or flat out refuse to sell parts to you apple style.
@TheTechenthusiast6910 ай бұрын
your wish has come true
@JJ-wm9lo10 ай бұрын
Lets anwer this comment the day they will
@davydatwood3158 Жыл бұрын
Broadly speaking, I agree with your conclusion: if you're in the part of the "3d printing community" that doesn't care about building and modding a printer and just wants a tool for making things, the Bambu machines are probably the best choice. The one advantage Prusa has over Bambu is a proven track record, though. If you're a very risk-adverse person, Prusa is probably a slightly more stable company. Not that I have any reason to doubt Bambu's stability, but we don't have long-term data. Likewise, we know the Mk3 in its many forms will run for years, and we just don't have that long-term experience with Bambu. (A subset of this, Prusa parts are available from a lot of different sources, meaning that even if Prusa suffers a catastrophe spare parts will be fairly findable for some time. Whereas Bambu is currently a single-source machine with minimal fallbacks if something happens to the company.) Until I watched this, though, I hadn't thought about the Prusa as an "easy entry" for those who *are* interested in building and modding. That's actually a really good point - getting the Prusa kits will teach a new printor a lot about how to build and maintain a machine, while still offering a lot of strong customer support and high quality parts. If yo're brand new but eventually want to build a Voron or a RatRig, the Prusa machine is probably a really good place to start. Also, you have no idea how happy you made me by remembering that "mk" is pronounced "mark." It drives me bonkers how many KZfaqrs say "emm-kay-three." We don't say "dee-are McCoy" or "Fleet ess-tee," after all!
@damiengvideos4337 Жыл бұрын
As someone that has exclusively used 3 Prusa MK3S+ printers for several years to run a highly reviewed Etsy business I recently ordered my 2nd X1 carbon and will be replacing the Prusa printers. The X1 Carbon somehow prints at 2-4x the speed and even beats the Prusa on quality…I truly didn’t that the quality would be there but somehow it it! I LOVE Prusa they helped me build a great business but somehow Bamu Lab has mateched and even beat Prusas magic sauce.
@raular5513 Жыл бұрын
do you have a link to your store?
@wishihadablog Жыл бұрын
Did you think about spare parts availability? One big plus of Prusa is that all the parts are open source.
@damiengvideos4337 Жыл бұрын
@@wishihadablog Yes I did consider that. Sorry at some point you have to just give something a try. I have 3 X1 Carbons running full out 20 hours a day and they have been going like that for about 4 weeks now. I’ve had one single clog in all that printing and 2 failed prints..that roughly 1800 print hours already between the 3. Also the replacement parts seem to be readily available on the Bambu website at quite reasonable prices at the time of this comment. Time will tell but so far I have no regrets at all in abandoning my MK3 printers.
@jamesharris9894 Жыл бұрын
@@wishihadablog spare parts are readily available and pretty cheap but bambu labs filament or spools is more complicated always sold out. and I live east coast so take 7 to 10 days get parts atm but sure that all get better
@blm7929 Жыл бұрын
@@damiengvideos4337 spare parts are available now, but what about the future ? What about they decide to release a new printer and stop selling older parts ? What about Bambulabs dissapear ? Most of Prusa parts will be available for ever and ever. I talk just about spare parts, not the rest (print quality, speed, etc) which is surely better than the Prusa. I have only a doubt about print quality as the majority of X1C users says that the print quality is a just the same as the Prusa.
@JPspinFPV Жыл бұрын
3d printers were always destined to be plug and play appliances, and Bambu is the first to reach that mark. I LOVE to tinker! But I want my printer to be a tool I use in my tinkering, not my project. After getting my hands on my friends new X1 carbon it's a no brainier. My highly modded CR10 has seen the last of it's upgrades. Bambu will surely put out a machine with a larger print capacity and I'm here for it.
@slamoto2 Жыл бұрын
The preorder bonus of the p1p is a low res cam, the fan and a light. Which is great. Ill add the fan an adjust the settings for sure. I will also print myself a enclosure. Cant wait.
@satori_mountian_station Жыл бұрын
I love that bambu are actually innovating!!!
@UncleJessy Жыл бұрын
Fantastic video / deep dive Also… those broll shots you are making are just 🤯
@247printing Жыл бұрын
Hey man, thanks a lot - that means a lot to me! Merry Christmas to you and your family!
@ootoriazumi1349 Жыл бұрын
to really be more relevant, i think Prusa needs to make a corexy Prusa Cube that works with their toolchanger and multi filament system. especially since they are making their fork of the marlin input shaping algo and a corexy takes better advantage of that feature than an i3 bed slinger type. the cube footprint helps it fit spaces without needing to worry about extra front or rear spacing. having the bed stationary, layer shifts from bed acceleration or a slipping magnetic bed arent really a concern anymore. everything just goes fast.
@phimuskapsi Жыл бұрын
I started with an Ender 3 Pro and struggled and loved it for 2 years. The P1P is the "next step" in my printing evolution, I'll probably even print parts for the Ender ON the P1P. I'm glad that I understand the devices at a fundamental level, from calibration to configuration and building.
@JessicaVandal Жыл бұрын
Prusa overall I still feel will have Bambu Lab beat on track record and range of products for awhile now. They're continuing to expand into newer and newer spaces and are never too far behind with innovation. Excited to see the Prusa XL once it's out, it looks like a really REALLY exciting printer for the people that wanna go big or go home. Overall, solid review, appreciate the unbiasedness you have.
@monkeyfingerslocksport6429 Жыл бұрын
I just got my P1P setup and running after 2 years of extensive mods to my ender3 pro, best learning experience build, fix ,rebuild, tune
@naidta9802 Жыл бұрын
Bambu is changing the 3d printing market!! 🔥
@247printing Жыл бұрын
Exciting times, right?
@leesmithsworkshop Жыл бұрын
I made my two Rat Rig based Corexy printers just before the X1 was released so I had no money to join the KS and I do feel like I missed out on something special. After the P1P was released I decided to upgrade one of my printers with the Rapido and LDO motors and I can compete with the speeds so that made me feel a lot better, but I really would like the X1 Carbon with the multi material setup. My Prusa is still my go to printer for anything that needs PETG, ASA or PCCF it prints those so well with a small upgrade of a nozzle X. I do have the MMU for the prusa, but I was never able to get a reliable filament rewinding system in my small space so I removed it. Bambu really have done a good job of shaking up the printer market for 2023, exciting times !
@247printing Жыл бұрын
Today I saw content of Adam (Vector3D) about really handy filament clips. I want them, but don't need them quickly. Started Prusa Slicer, picked a default setting, sent it to Octoprint and started the print on the MK3 blindly. If not in a hurry: It still has it's nice touch!
@MakerBees333 Жыл бұрын
The Pampers😂 blooper got me going as I was literally carrying a used pampers to the trash when you said that and seriously thought for .2 sec you were seriously about to incorporate diapers to the Bambu 😂😂. Merry Christmas, thanks again for the most insightful videos about Bambu on the internet! 😊
@247printing Жыл бұрын
Hey Theodore! Merry Christmas - nice to have you here again and thanks a lot for watching to the end!
@Defyant123 Жыл бұрын
The X1C is has transformed my little printing farm into a cash collecting win fall... The speed i can smash out clean looking prints is just next level. The P1P is just the next step to converting all my machines over eventually. But... @ nearer to 1k au and by the time you add an AMS ($500*) Then the extra's.... IMO if your looking the multicolour then the X1C still represents better overall value imo. The day Bambu Labs decided to release a 300 x 300 or even 400 x400 printer it's game over.
@Vez3D Жыл бұрын
Incredible video quality man. Great review. Merry Christmas buddy
@247printing Жыл бұрын
Thanks a lot, Simon! Merry Christmas to you man!
@shenqiangshou Жыл бұрын
Agree. My MK3s has been off ever since my X1C has been running. The only thing the Prusa has going for it right now is quietness. I use to be able to have the MK3s on my desk printing and still have a work meeting. With the X1C, even in silent mode, is too loud and annoying. However, with how sturdy the X1C is, if I need to do a print during work hours, I just pick it up and move it to a different room, then use it remotely, since sending files and monitoring the print are both super simple. Like many others, I am also have a Prusa XL on preorder, although, after rounds of delays and no end in sight, I wonder if I will even bother following through now that I have the X1C. Especially since the X1C with the AMS does everything I wanted the XL to do, and faster.
@damiengvideos4337 Жыл бұрын
Exactly!
@sofronio. Жыл бұрын
I just got my p1p. The setup is really easy, and the printing quality is amazing. Sure it's possible to achieve that speed and quality with a voron, but that takes time and money and most importantly experience. Do I still love my prusa and voron? Yes. Those you build with your own hands are quite something else deep in heart. But if I want to buy another printer, and just want it to work, it will be again the p1p.
@JamesFryerCreative Жыл бұрын
Tremendously useful video, thank you! I almost bought a Prusa a couple of weeks ago... so glad I waited to see more from all these new printers.
@jaylawvlogs264 Жыл бұрын
If you already have Prusa printers , they do produce good quality. ( with some upgrades ). I have 9 Mk3 s. Minis etc. after receiving the Bambu x1 carbons. They are my new go to printers. Now I do still use the prusa s. But usually just to mass produce something. if I need to print quickly it’s so much faster to do it on the Bambu printer. I had a deposit for a couple of the Prusa xl s. But honestly I don’t really see a need for it. I could buy 6 bambu p1p s. For the price of the XL from prusa. ( with the 5 tool heads. ).
@damiengvideos4337 Жыл бұрын
I’m in the exact same boat. I’ve exclusively loved and used Prusas for the last few years and have a deposit down on 2 XL model but have canceled one. I just don’t see how an XL with 5 tool heads for $4k can possibly replace a single X-1 Carbon with AMS for $1500. Or add 3 extra AMS units for a total of $2550…16 colors and superior speed. I hope this wakes up Prusa and they put out a better, faster machine. Win win for us consumers!
@adamriese3610 Жыл бұрын
i dont own a prusa nor im a fanboy of it, but i think the main reason going to a Prusa XL is the more stable build quality (maybe for long term use, if it matter) and you have a multi material printfarm not to ooze so much filament. But there is a lot oozing before break even...
@BH4x0r Жыл бұрын
@@adamriese3610 more stable build quality? it uses plastic parts, it doesn't have supporting extrusions in the front etc.. there's just so much wrong about the xl, the only 2 benefits of the xl would be the larger bed and the toolchanger, and that's about it
@damiengvideos4337 Жыл бұрын
@@adamriese3610 I love my 3 MK3S+ printers 🖨️ for their quality. However my X1 Carbon is so much faster and is even better quality than the MK3. I hope the XL steps it up even more! Then we all win 🥇
@adamriese3610 Жыл бұрын
oh, i think i mixed up something. Yeah right the missing front extrusion is weird... dont ask me. I got a sidewinder, and now using a voron i dont buy a prusa. The price for the hardware is too bad for me, even when they use excellent software and documentations
@chillinator Жыл бұрын
I have two X1C's and a Prusa MK3S+ and although I really enjoy using the Bambu machines, I won't be retiring my MK3 any time soon. Yes, it's slower, but a decent number of my prints are run slow and hot, so that's OK (PC-CF for one) - I get fantastic results from the Prusa. I also like Prusa Slicer better than Bambu Studio as it feels more mature and feature-rich - although now I've had the network connectivity of the X1C, I really miss that on the Prusa. I've also had more issues with the X1C (bad camera, bad heatbed sensor cable, filament jams - in just a few months), and I don't think the firmware is "there" yet. Even with all the fancy sensors, it will still under-extrude, phantom print, and other dumb things. I've had to clear several plugged nozzles on my X1C's and never had that happen on my Prusa (knock on wood). Now, if I was recommending a printer to a noob on a limited budget .... I would have to point them at the P1P over the MK3S+ (kit). Yes, it's proprietary in a lot of ways, but Bambu's part pricing is very reasonable and their shipping is quick. The results (especially using Bambu-branded materials) are excellent and fast. It will be interesting to see, over time, what modders do with them.
@DEtchells Жыл бұрын
The UPS man just dropped off my X1C Combo, I can’t wait to get it printing! 😃
@viru52000 Жыл бұрын
The nice thing about reprap open source style printers (Prusa, Voron, etc) is when things inevitably wear out or break, the parts are off the shelf components and 3D printed parts. This also allows easy upgrades (Prusa is notorious for this) If Bambu Labs stops making parts, you now have something going into a landfill. They went too far into the appliance black box side of things IMHO.
@8bittim Жыл бұрын
Said something similar on Reddit. Right to repair is huge, you have to send this back to get it fixed, and like you said, it's a big expensive paperweight if Bambu goes under. Secondly, prusa isn't a thing of the past. I have the xl on pre order and that thing is stuffed with all kinds of fancy tech that the x1c doesn't even have. And you can be sure all of it will be drizzling into a more affordable Mk4 any day now with an announcement.
@shanebrennan4657 Жыл бұрын
@@8bittim The XL most likely wont be as fast as the Bambu's though. Most people switching to the Bambu's are people who print as a business and time is money.
@oddlytimbotwillison6296 Жыл бұрын
Yep. I was with an org that went all-in on Printrbot back when. They went out of production, and all the printers slowly died because the control boards were all proprietary.
@8bittim Жыл бұрын
@@shanebrennan4657 my comment must have not been posted or deleted but I'm on the FB group with Bambu labs and most of them are hobbyists. But aside from that, the prusa has so many features speed isn't a concern of mine. I can't speculate on it either because they haven't made a statement about the exact speeds but they did claim it will be able to go pretty fast. It's the sum of many parts that makes this printer extremely interesting for me
@shanebrennan4657 Жыл бұрын
@@oddlytimbotwillison6296 they had low sales though, which suggests the marketing and product/ timing wasn't right. From what I have seen with Bambu Labs I predict it will be successful if they can iron out the small teething problems.
@MandicReally Жыл бұрын
Excellent video 🎉 I couldn’t justify picking up a P1P having a X-1 but it’s value is hard to ignore. 👌🏻👌🏻
@247printing Жыл бұрын
Thanks a lot, mate! I double that - no need for me to have a P1P (printing a lot of ABS), but it's an appealing machine (naked and sexy...) in every respect!
@MandicReally Жыл бұрын
@@247printing yea, I print ASA & ABS more than PLA these days, part of why I skipped the P1P. 👌🏻👌🏻
@Ughmahedhurtz Жыл бұрын
Good summary. The real dilemma I see is whether the Bambulab models will hold up as well as the Mk3S+ in terms of wear/adjustment/etc. I've built a Voron 0.1 and my Mk3S+ and aside from a bearing issue with the Prusa (no, the linear bearings are NOT pre-lubricated lol) I haven't had any problems with either. I'm looking hard at the X1 Carbon just because it takes all the MIND-NUMBING and error-prone guesswork out of tuning resonance, pressure advance, and extrusion rates. I really, REALLY loved how the default profiles from Prusa just worked out of the box with their filament on the Mk3S+ but as soon as you want to move to something more useful like ASA or other engineering-grade (lol, I know) filaments, you have to go back and retune so many things that it becomes a real drag. I'm past the "I wanna build the kit to learn how this stuff works" and well into "get off my lawn, I just want it to print well all the time." Warm regards from Texas and Merry Christmas. ;) (not so warm here, though. Was 10F/-12C here last night.)
@LilApe Жыл бұрын
Tons of problems are already coming out with the X1. Check reddit, twitter, fb groups, etc. My friend just got his X1 last friday, and the same day the stepper motor went bad and he still hasn't heard back from bambu CS. Didn't even have 10 hours on it. Just another china made printer with china made parts and quality.
@Ughmahedhurtz Жыл бұрын
@@LilApe That's disappointing.
@seashadow5239 Жыл бұрын
Bambu has been pretty transparent and open. They told the community that due to the Covid outbreak CS would be degraded and apologized in advance. I have a KS unit, and the 2 times I've had to reach out I got responses in
@Ughmahedhurtz Жыл бұрын
@@seashadow5239 Interesting. Thanks for the feedback. ;)
@sore500 Жыл бұрын
Prusa? Who?
@d.i.d Жыл бұрын
I saw it in museum ;p
@djanny8951 Жыл бұрын
chillax :) Prusa is far from obsolete, if you are a prusa owner you know why ;) lets see how sturdy bambulabs p1p is after 1 year in the field :) good luck ! keep printing
@YourLocalRaccoon Жыл бұрын
With how well engineered the BambooLabs printers are, they could probably up the print size by quite a bit without having to sacrifice print quality or speed too much. I expect an X1C+ or X2C at some point 2023 with just a larger print size and probably more filament roll storage space on/within the printer.
@morbus5726 Жыл бұрын
in bambu's AMA on reddit, the ceo said that a future large format printdr wouldn't just be a scaled up x1c, they would add a lot more features, and redesign many parts.
@YourLocalRaccoon Жыл бұрын
@@morbus5726 even better!
@247printing Жыл бұрын
I double that: Ingenious engineering there! I also think easy scaling the X1 to 300-350mm from a design point of view should be doable. The problem for a bigger sheet metal frame like this: Loads of investment for tools and assembly to do by Bambu Lab and it's a smaller market. Maybe 2023! I'd be excited!
@damiengvideos4337 Жыл бұрын
Agreed…an X1 Carbon with a 350-360 build build plate to match the XL and it’s game over. I LOVE Prusa but the competition is heating up which is great for us consumers!
@sicstar Жыл бұрын
Stumbled upon this channel when looking for voron tuning and insane speedboats. Now you doin printer reviews too :O ? And the video quality is WAY TO GOOD for that "low" sub count. Happy for anything coming up in here. And i wish you a good new year!
@247printing Жыл бұрын
Happy new year to you! Cool to read that you are one of the early viewers still sticking to 247printing! THANKS! Yes, this year I tried to learn to produce proper content, but I'll come back to the roots (insane speeds) next, but then with better video quality :-)
@sicstar Жыл бұрын
@@247printing Yeah your first 1000mm/s V0 vid made me make my prusa go brrr :| far from your V0 but now it manages a decent quality benchy in barley under 30 minutes in PETG, thats enough for now :D And excellent review. Can't argue a bit. Also very interested in whats coming next :O
@TheJacklwilliams Жыл бұрын
I think it goes without saying that Bambu Lab knocked it out of the park across the board. However, I find it odd that they don’t offer an upgrade path for the P1P to carbon level and it just limits the amount of money they can make. Aka, you should, be able to buy the stripped down P1P and upgrade it, fully over time, to the Carbon. In the end, it would cost more, but allow the customer to outlay the fundss over time. Aka, the budget constrained could still get in, and over time, have the same product and? Bambu still profits well from it. Re Prusa, they’ve manaaged to set the standard for years, but, obviously haven’t innovated in too long. I bought a Sovol SV05, modeled after the Creality 5 and it cost me 279.00. Creality, is the ones that made Prusa over priced. Joe and gang however, aren’t “done” in my opinion. I believe it won’’t be long before we see their response to the market changes. Will it be too late? I don’t think so. Don’t count them out yet.
@maxmustermann194 Жыл бұрын
This review makes me really consider buying one as an upgrade to a Qidi Tech i-Mate S. The precise detail of information needed, superb charts and great voice-over.
@DWIT3D Жыл бұрын
Great comparison, thank you. As a channel just finishing up the 4th Voron build, I'm curious to see what I think of the P1P when I unbox it on New Years Day! Super excited!
@redline3036 Жыл бұрын
Love my x1c but I can’t wait to get my trident started and finished really looking forward to my first voron.
@247printing Жыл бұрын
Thank YOU for watching. You are one of those who just embraces 3D printing - love it!
@DeKempster Жыл бұрын
For me. fully opensource, made in Europe, smaller size(Bambu is to big for my IKEA cabinet) makes Prusa the clear winner
@ilikecringe Жыл бұрын
No joke the other day I was thinking about laser bed levelling, I tried googling it but couldn't find anything and now it's in this printer
@LilApe Жыл бұрын
It doesn't use a laser for bed leveling lol. It uses load cells. The nozzle just pushes into the bed to lvl itself.
@Higlac89 Жыл бұрын
Honestly if I were wanting a printer that just works without tinkering then I'd still recommend the prusa over the bambu lab. There's good slicer profiles for nearly every filament, there's better access to spares and the supply chain is there. It's a proven platform and the support is just miles better than what bambu lab have in place. I think the bambu lab printers can take that spot away from prusa, but it's just not there yet.
@morbus5726 Жыл бұрын
the bambu printers also have profiles optimized for almost every filament, including bambu branded, generic, and polymaker.
@davydatwood3158 Жыл бұрын
The single issue I don't like about the Mk3 is the old-school nozzle. I find getting the 2-part nozzle and heat break seated properly incredibly difficult and I've ruined two different hotends because of blobs of doom caused by imperfectly seated nozzles. I think Prusa would be well advised to switch the Mk3 to the same nozzle the XL will be using.
@YourArmsGone Жыл бұрын
@@davydatwood3158 I agree. While I have never damaged my hot end switching nozzles was always difficult and nerve-wracking. That's why I upgraded my prusa with a Revo system switching nozzles is so much easier. Prusa should just make them or something like it standard.
@user-tj7xr6xd9z Жыл бұрын
Prusa no longer has any secret sauce. Alot of printers now are on par or better. People using prusa's just don't know cause they've never really explored outside there box.
@3dFuzzie Жыл бұрын
I love my bambulab X1CC , Prusa is a old Grandpa 🙂😄
@georgskleinewerkstatt8678 Жыл бұрын
Frohes Fest! Und Dankeschön für das tolle Video. Super geschnitten, sehr informativ. Dein Englisch ist klasse, Hut ab. Rundum Super!
@Traitorman..Proverbs26.11 Жыл бұрын
A printer made mostly with proprietary parts will never be a Prusa killer. Just you wait. After two years the P1P will be discontinued and the “upgrade” won’t be able to re-use the proprietary parts.
@8bits955 Жыл бұрын
brillant video! My own personal opinion on the Bamboo Labs printers is that they are absoletly amazing high speed printers for a fairly reasonable price that is fairly fool prool and are great for the people who just want a printer that is high speed and just work with little to no tinkering/building required. However with that being said, i can say that for most people in the 3D printing community we will often spend more time on tinkering and upgrading our machines than spending time printing stuff. So it really down to the persons goal and what they want out of a printer to go with Bamboo Labs or others like prusa, voron, ratrig or even vzbots. I personally feel that the Bamboo labs are targeting more towards small businesses and engineering firms rather than everyday hobbiest printer guys, where they requires high reliability and fast print time and most importantly no tinkering, to just get prototying parts out.
@TheJttv Жыл бұрын
Having been in the 3d printing world for over 7 years. I just want my printer to work as my time is now much more limited and i want to focus on designs not tinkering That said i never buy a gen 1 product from a new company. Maybe in a few years tho.
@shiikon2193 Жыл бұрын
I love tinkering and upgrading but holy fuck it gets annoying after a while especially when I need to get something printed asap
@8bits955 Жыл бұрын
@@shiikon2193 yep that is why we need a reliable printer on the side
@KanielD Жыл бұрын
8-12 hours more than doubles the price for me. The kit is the only way I’d get the Prusa, however, I couldn’t choose it over the X1 for the same(ish) price. I understand the sentiment about building the printer yourself, however that argument is starting to sound like the “you learn from upgrading an ender 3” both are true, but are they necessary?
@ThomasS17 Жыл бұрын
If your plan is to just get an X1(C) or P1P, I think the argument of "learning by building" is mostly irrelevant because you can't really upgrade or repair much yourself anyway.
@albertoyarmuch Жыл бұрын
Hi Albert, Nice review. I think, that is the future of 3d printers. Greetings from Bochum Albert
@247printing Жыл бұрын
Hey Albert, thank you! Greetings from near Landshut, Albert
@TioDave Жыл бұрын
As a hobbyist I'm cautious about printers in closed ecosystems of parts. Given it has a fast growing following. I rather build a Voron and be able to purchase parts from more than one manufacturer. Also being able to upgrade to suit my needs. As a consumer my interest is peeked, but I've done the early DJI dance and was let down. Eventually they came out with products that resolved the issues created by their new design techniques. I would suggest the p1p or carbon to anyone who doesn't have time to put one together.
Жыл бұрын
This vidoe is more a P1P comparison with X1C than really a P1P vs PRUSA... Which is great, because I was actually looking for videos of X1C vs P1P! :D
@247printing Жыл бұрын
Thinking about it... Yes, you are right! I tried to set the P1P into perspective.
@GAMERSW0RLD Жыл бұрын
Have a good Christmas 🎄
@247printing Жыл бұрын
THANKS MAN. Merry Christmas and have a great new year!
@TableTopBiker Жыл бұрын
Man, I love your videos. My P1P came in a few days ago. I was debating making an unboxing video but now I am debating doing a live stream since Uncle Jesse's machine had screen issues out of the box. As he said, it still could be user error. We will find out. Thanks for the content.
@247printing Жыл бұрын
Thanks a lot mate - have fun with your P1P! I totally fell in love with that naked bare look of the frame! I think I won't enclose it :-)
@Bearded_Blonde Жыл бұрын
Love my P1P, only issue I'm having right now, its not recognizing the camera at all. They should give the option buy the glass door and top for the p1p considering it's just a shell of the X1C.
@zachofalltrades6116 Жыл бұрын
You can buy the glass top I’ve already seen one with it applied on a Fb group looks really good
@Bearded_Blonde Жыл бұрын
@@zachofalltrades6116 I'll have to check that out thanks!
@mikegrant8031 Жыл бұрын
As someone who wants to print not build or work on printers, bamboo is the only choice. Build size is the only thing I waffle on, some of the huge format printers are enticing. Extrusion printers will have to outpace my mono X's before I leap in.
@Fluffywings84 Жыл бұрын
Thanks for the video! Please put up charts for longer or put in the description. Watching on a TV was not possible as paused the chart was covering key details. I had to swap to my phone
@247printing Жыл бұрын
Thanks for the feedback, very precious and we've discussed this topic a lot internally - I was on the "pausing is always possible" side. You proof that wrong - I'll find ways to make this more enjoyable in the future!
@Fluffywings84 Жыл бұрын
@@247printing If you need any more on this, so we also tried to even take a picture of the graphs on the TV with our phones and it took three attempts as it was that fast. 1 missed completely 1 missing the last bar. Thanks again for the video!
@Lamia768 Жыл бұрын
Hello there! :D wanted to ask you if you have made more progress in your speedprinting 3dprinter. really loved the videos of speedprinting
@247printing Жыл бұрын
The next one is about that! Thanks for asking
@MrButuz Жыл бұрын
As soon as I saw that bambu was DJI led - I said that the rest of the 3d printing industry is completely screwed lol. They decimated the competition in the drone industry whilst turning it from a handful of DIYers playing around with fibreglass into a billion dollar a year industry that's now used in every form of life daily.
@247printing Жыл бұрын
Around the same for me: They had full trust from my side for backing their Kickstarter after I realized their heritage.
@wesleydutoit6901 Жыл бұрын
MAN OH MAN! What great detail! Im a mechanical engineering student and you really tickled all my concerns in investing in this 3D printer, which is a good and bad thing. As I am a student, Im worried about investing all my hard earned money in a printer. Would you maybe have a recommendation on a 3D printer I could customize, make a enclosure and dismantle, whilst still printing at a good speed and quality and range of materials? Its a lot to ask for but there's so many choices that im a little overwhelmed.... XD I also live in Austria, if that helps with a recommendation :) Thank you for your effort and great quality for information!!!
@Arek_R. Жыл бұрын
PRUSA been siting on same design for way too long and the derail into resin printing was another nail to the coffin
@jstro-hobbytech Жыл бұрын
To say you're not a big fan of the cheaper p1p screen is akin to saying the same about the prusa screen. Just saying. All due respect. A prusa xl themed enclosure would be hilarious. I respect you so much for marking a line in the sand even though a diy creality kit from their site would be a great, no big expense way. I've never met a German who didn't like metal. I approve haha
@247printing Жыл бұрын
Hard to compare the Prusa screen and the P1P screen: Different approaches: The encoder style on Prusa is faster and more convenient to use. Also less delays. If you have the opportunity: Try to check out both to get a feeling!
@jstro-hobbytech Жыл бұрын
@@247printing good point my friend.
@blm7929 Жыл бұрын
When I switched from Ender 3 V2 with its big LCD color screen to the Prusa i3 MK3S+, I thought "what a screen downgrade !". I planned to ad a touch screen connected to my octoprint. But after the first interactions with the controls, it's way better than the controls of the Ender 3 V2 itself. When you know it, it takes few seconds to do what you want to. It's very intuitive and effective. I will say even better than a touchscreen with a bad or just good UI. After two years, I print with my Prusa several times a week and never put the touchscreen that I wanted to the first time... By seeing the controls of the P1P, when you have the Prusa i3 experience, you know within a second that they are worse than the Prusa. Especially with theses buttons.
@JohnOlson Жыл бұрын
I’m still sticking to MK3S (even a clone) or Voron. I don’t want a closed box 3d printer. Your repairs and mods are controlled by Bambu. Your personal needs may differ. That’s fine.
@sore500 Жыл бұрын
🤣🤣🤣
@morbus5726 Жыл бұрын
What's the point of modding when a printer has almost every feature imaginable? It's the same reason why people don't usually mod prusas
@JohnOlson Жыл бұрын
@@morbus5726 Mods galore for Prusa i3s. Extruders, hot ends, bear frame, linear rails, revised printed parts for easier belt tensioning, fan duct for improved cooling, lighting. And more.
@rehepeks Жыл бұрын
@@morbus5726 The point of modding is modding. If I take the time I've messed with my printer or printed anything then most of the time I have spent modding it. And its not because its not working. It's because I have no need to print anything but I like tinkering with stuff.
@Brett5106 Жыл бұрын
@@JohnOlson I would not buy a Prusa with the thought I'm going to mod it. Sorry, if I'm going to spend $800 to $1100, I don't want to tinker or mod anything. I just want it to work. Bambu with quality and speed combo is a no brainer. The cost is very good for what you get.
@AlexChangYuan Жыл бұрын
"Prusa just works." "Inch just works." Does not mean we cannot improve.
@getfastfish5020 Жыл бұрын
when you said prusa killer I had to check the date this video was uploaded
@eds3dshop29 Жыл бұрын
Richtig gutes Video! 👍 Hast Du Dein Weihnachtsschnaps ehrlich verdient! 🎄🍻Danke Dir und schöne Feiertage Dir und Deinen Lieben! 🖐️😃LG Ed
@247printing Жыл бұрын
Danke dir! Das wünsche ich dir auch - weiter so mit deinen Modifikationen!
@eds3dshop29 Жыл бұрын
@@247printing Danke Albert, freut mich, dass es gut ankommt 🙏🖐️😀
@mag_rag3504 Жыл бұрын
Well done Albert!!
@247printing Жыл бұрын
Thank you! Merry Christmas, Oida.
@Heymeit Жыл бұрын
Stopped using my Voron since my x1 arrived. No time for messing around.
@247printing Жыл бұрын
I can understand that. Sometimes it's happy tinkering and sometimes it's just annoying messing, trial and error.
@Heymeit Жыл бұрын
@@247printing especially for prototyping and production. Nothing is worse than babysitting z offset first layers.
@Creative_Electronics Жыл бұрын
Nice video, those Bambulabs are insane!
@DoktorSkill Жыл бұрын
The only thing that bothers me, is that many reviewers claim that the P1P/X1 is loud and shouldnt be in the same room as you most of the time. Like you already said. Since i have my gaming PC in the same room its important for me, that the printer is as quiet as it can be.
@extectic Жыл бұрын
That's one of the advantages of the Prusa. It makes a fair amount of noise too, but if you first get a very heavy paving stone that's like 40x40cm squared and thick, and put that under it to soak up vibrations, that quiets it down a lot. If you then also add an enclosure, that will control the fan noise as well. I run my MK3 in my office space in a makeshift enclosure and I can live with the sound. Especially since i print PETG almost entirely; PETG doesn't need the maximum cooling PLA does, so the tiny fan doesn't have to spin at a gazillion rpm and howl its head off.
@LilApe Жыл бұрын
I run multiple prusa printers 5 inches away from me on the same desk where my gaming PC is set up. They sit on 1/2 rubber pads from home depot and they are just as quiet as when i use to have them sitting on a heavy concrete paver. I can sleep in the same rooms in my prusas. Cant do that with a bambu. even when running bambu at really slow speeds. Its just ridiculously loud for no reason.
@247printing Жыл бұрын
Loudest thing are the resonances of the stepper motors - an easy fix for people who watch CNC Kitchen :-)
@DoktorSkill Жыл бұрын
@@247printing change stepper drivers?
@247printing Жыл бұрын
@@DoktorSkill stand it on a resonance absorbing surface
@John_Mack Жыл бұрын
I have a laser printer. It prints my documents without having to tell it what speed to print, what temperature to use, etc. That's how I want my 3d printer. Notice how "I" want it. Bambu Labs is a step in this direction. Next, let's get A1 involved in the software so I get PERFECT prints every time, just like my laser printer.
@247printing Жыл бұрын
Let’s see when we will be there!
@fhesse9724 Жыл бұрын
Great Video. Was fun to watch.
@247printing Жыл бұрын
Hey Franz, there you are! Danke vielmals und dir frohe Weihnachten.
@Patrick-pm1sn Жыл бұрын
Ordered one and really looking forward!
@orhanyor Жыл бұрын
Bambu lab puts the Prusa in an odd position. The features of X1 is just another generation and tech compared to mk3 which offers waaay more features. I feel like if prusa made the X1 they would have priced it at least $2.5k for comparison you can see their barebone XL which is priced at 2k and its made of extrusions/3d printed parts and lacks features compared to X1
@orhanyor Жыл бұрын
Fast forward 2 months. I just received my X1C carbon with AMS and i would like to say money well spent
@ywsx6489 Жыл бұрын
i hope bambu labs makes a printer with > 300mmx300mm print area.
@norbertlukacs3661 Жыл бұрын
Honestly I prefer prusa (for now). It's open source, original and clone parts are available, even if the production ends youll be able to buy parts. Although, the competition is always good for us, for the customers, so I'm happy for bambulabs. It's a great product and looks very promising
@timzalusky Жыл бұрын
The max bed temp of the X1 and X1 Carbon is actually 120C in the US (or any 120v region) Just tried it yesterday.
@pierholtrop54323 ай бұрын
On their website it says 110v 120degrees and 220v goes to 100 i think
@75echo Жыл бұрын
Ofcourse the prusa mks and minis are now obsolete ...just like that and overnight because Prusa have been lazy in R and D for a long time. They have even realized it themselves and sent out questionnaires to hear what they can do to fix it .
@JohnOlson Жыл бұрын
Bambu didn’t do any new R&D work related to 3D printing. They took everyone else’s work and mass produced it.
@sculptaware4548 Жыл бұрын
@John Olson that's literally what all R&D departments do. These companies will not pay for REAL engineers to innovative new ideas. They can't afford to. Prusa definitely doesn't either and they also just take from the community as well. They don't innovate. All the low budget 3d printing companies just take and mass produce some clever, most of the time nameless, engineers work they did as a hobby and run with it.
@morbus5726 Жыл бұрын
@@JohnOlson do you understand what r&d is? They research what other people are doing, and package it into a complete product. They actually talk about this on their blog, and give credit to projects like the reprap project, the voron project, hevort, ratrig, etc.
@tiestofalljays Жыл бұрын
I’m not sure you know what obsolete means.
@bobbystem7384 Жыл бұрын
@@JohnOlson how dare they not re-invent the wheel... they've brought a fantastic product that ticks every possible box at a price equal to or lower than the very best competitors. There is nothing to complain about
@paulherman5198 Жыл бұрын
Great review. This is a pretty good machine. The Sovol SV06 is supposed to be a great Prusa MK3 clone. I won't have mine for a couple weeks. I have been a huge fan of Prusa since they came out, but there are a few newcomers that are stepping up
@247printing Жыл бұрын
Thank you Paul!
@chillinator Жыл бұрын
The Sovol SV06 is very much LIKE a Prusa, but I'd describe it as an "early Beta of the MK3S" - it doesn't have a lot of the "nice to have" features of a MK3 (like filament run-out sensor or independent Z axis steppers - they're wired together - or the really user-friendly firmware). Still, for what they cost, they are a solid printer. I set up a profile in PrusaSlicer for the Sovol SV06 and it's been working great. If it wasn't for the screamin' PSU fan, it'd be almost silent, too.
@koffee3816 Жыл бұрын
its a very nice printer indeed, however the fact you can't upgrade it step by step to be like its higher tier brother is a deal killer for me.
@25Denjo Жыл бұрын
In my opinion at the positive site of Prusa is if you have to repair something you get the parts from the Market. For the p1p only from bambulab because all is proprietary. But overall i like the p1p, not much left to buy it.
@adamriese3610 Жыл бұрын
I Think you had the right Conclusion. In the End my main Question is, why Prusa didn't evolve in the last 5+ years and why they stuck so long to the bedslinger design which is imo a bad idea. I got an Sidewinder and then a Zero G (Voron fork) and im happy with my Voron but also jealous of the Bambu users and after building and tinkering i think a working machine is the thing i need. More than a Printer to finetune. The Question is, if a Prusa with a very very detailed guide to build it up and working nearly out of the box is the right thing to tinker. The best one is still a good old Ender 3 with 300-400€ stupid wasted Money for some mods. The only Reason for me to consider buying a very expensive Prusa was the beginner friendly design like sensorless endstops + the detailed documentation + the Community to get a lot of feedback to fix problems. I really consider buying a Bambolab and ditch my 350x350 Zero G. the p1p should be enough but its like apple you want a bit better then you can buy the X1 and the extra "few bucks" for the carbon with these nice features is a simple decision. But 1300€ vs 700€ is a big difference and most parts are the same... I just wish the hotend is quick changeable with different nozzle sizes and i hope they build up a great eco system with (at least now) very fair prices! PS: Haste deinen Weihnachtsschnaps gefunden? :P
@247printing Жыл бұрын
Thanks! Good question - a possible answer why Prusa didn't evolve much: There was not much need for this. The copy cats were cheaper anyways and mechanically it's hard to strengthen an IP. So they focused on small iterations of the product and on strengthening their ecosystem as well as all of their "secondary values": Such as support and quality/reliability.
@adamriese3610 Жыл бұрын
@@247printing its the perfect analogy to Nokia for me.... After the first corexy systems got big, they should have stopped the bedslinger design. Prusa was a bit behind but bambulab is the final nail in the coffin. Let's see it's very interesting
@AndrewAHayes Жыл бұрын
I enjoy building and tinkering and upgrading almost as much as the printing process itself, I probably will end up with an X1 Carbon as my Prusa XL has been delayed again, I know that if I bought a P1P I would be forever kicking myself for not getting the X1.
@dekopuma Жыл бұрын
It looks like Prusa is in an awkward spot right now. If you want a high end printer that works, you go Bambu. But if you want something that's a project, why not just go Voron or something like that?
@retrograpejuice Жыл бұрын
A prusa mk3 kit can be a good entry point for a noob. Community is huge and the project is very very well documented. I'm not sure if a voron is a good idea as a first printer.
@csdstudio78 Жыл бұрын
@@retrograpejuice yeah, voron isn't a great entry point into diy printers if you're green.
@parserthelynx Жыл бұрын
The MK3S kit is still good (and yet still cheaper than a V2 kit) if you want to ease yourself into a Voron. Sure, it's a slower bedslinger, but you get your experience building a more reliable machine than anything Creality ever spit out. I've had my MK3S for 3 years now, and the only thing it needs is some routine maintenance every now and then. I'm a hobbyist, so the MK3S suits my needs just fine. I want to build a Voron 2.4 just for fun. I enjoyed the MK3 kit.
@wellenbrecher Жыл бұрын
wie kommst Du auf den Preis für den X1 Carbon, oder soll er nicht inkl. Vat sondern exkl. Vat sein? Auf der Shopseite kostet er ohne die Anzahlung 1369€ + 19% (269,11€) macht 1629,11€ dazu kommt noch Porto und die Anzahlung von 20€
@247printing Жыл бұрын
Du hast bei der X1 Carbon Combo geschaut (mit AMS), da sind es die 1629€. Nur der X1 Carbon kostet das wie in der Tabelle angegeben.
@Agamemnon2 Жыл бұрын
If Bambu can come up with an Ender killer, we could see a major shift in the market away from these cheap and modifiable open-source machines and towards one controlled by more proprietary solutions.
@AarPlays Жыл бұрын
People complaining about "closed source" won't be using the same printer by the time closed source matters. Most people are going to sell and upgrade their printers in 3 to 5 years.
@infinitewars6373 Жыл бұрын
prusa did it again released a great printer :))
@Mr.Titanium1911 Жыл бұрын
I owned (yes, past tense) the genuine prusa MK2+ and MK3+ models. My X1 Carbon BLOWS them away. So long Prusa!
@L1nctech Жыл бұрын
Just got a X1-Carbon, but can't open it until christmas ); Can't wait tho! It'll be a HUGE upgrade from the Ender 3 v2 I have.
@Jeffmorgan1991 Жыл бұрын
I currently have an Artillery Genius, I am looking to upgrade and want to get a printer that is quite and has best finish quality. Would be great if someone with one of the newer faster printers tested finish and noise at lower speeds. It's hard to find reviews that focus on that side of things. Been watching your videos for a while and really like them, thanks for putting them out
@kilianlindlbauer8277 Жыл бұрын
They are always noisy. Tmc drivers are not always silent or silent because they are tmc drivers, it depends in which mode they are. Stealthchop, the silent mode, is weaker, less accurate and has less maximum speed compared to spread cycle, the performance mode. The bamboo uses exclusively spread cycle, otherwise it couldn't move as fast as it does.
@achannelhasnoname5182 Жыл бұрын
I'll never get a Bambu Lab printer for the simple reason that they are sending everyone and their dog free printers. If they can just throw them out for free, I don't see myself spending so much money on it.
@skymoon0731 Жыл бұрын
I have been using 3d printer for 3 years. cr6 se , Sapphire plus and bluer. Now I want to buy new printer but I am stuck between Bambulab and mk3s+. because Bambulab scares me about spare parts.
@workingTchr Жыл бұрын
I wouldn't have found my way here if I was able to get my new Ender 3 Max with Sprite Extruder Pro and CL Touch working. But now, seeing what new tech (like this and the FLSUN V400) is available, maybe that was for the best ...
@IamG3X Жыл бұрын
Corexy is the trend and probably is the future. Print faster and take up less space. Prusa just need to step up a little bit.
@ReudigaDeOfficial Жыл бұрын
Bambu Lab sieht schon krass aus... was ich da an Ergebnissen beim P1P gesehen hab. Uff... da kann Prusa etc. echt einpacken, zumal wenn man die Zeit dazu rechnet
@247printing Жыл бұрын
Die Zeiten ändern sich grad heftig, ja.... hat lange gedauert!
@kennytinker24 Жыл бұрын
Just wonder with those kind of speeds, will it beat itself to death? shorten its lifespan? and the unknown of reliability and durability? So many questions, new to this, so I have lots of Rookie questions.
@zues287 Жыл бұрын
Most of the parts on 3D printers are damn near bulletproof. I've been pushing my printers to their limits for years, and never had a non-consumable part fail. Stepper motors are near bulletproof, and as long as electronics are kept within their operating range, they'll last for many years. I've been running a few Ender 3's on Klipper so fast that they shake the heavy table they're on for 2 years. The only thing I've ever had to replace is rollers and a belt. The Bambu Labs printers are on linear rails, so don't have to worry about rollers.
@RicardoHernandez-ih1fp Жыл бұрын
I stopped using my Prusa ever since I got my 1XC, my Prusa feels antiquated now 😅
@247printing Жыл бұрын
Psssst....: Me mostly too.... But I still use it for print comparisons and smaller parts
@officialspock Жыл бұрын
If only I knew that Bambulabs will release P1P, I wouldn't have bought other 3d printer
@drewmalbica7694 Жыл бұрын
I want to step up my game from a base ender 3. Mostly for hobby use and maybe some prototyping. Looking at this over the Prusa. For me I can get it for less money.
@tomboard Жыл бұрын
What do you think of the Reality K1?
@247printing Жыл бұрын
From specs and price it looks promising, but I haven't received it yet, so I can't tell yet.
@tomboard Жыл бұрын
@@247printing Waiting with anticipation for your wisdom!
@edrumsense Жыл бұрын
The biggest issue of 3D printing is the learning curve, any one with no technical experience will have a hell of a time trying to make their way to 3D printing, This product is oriented to people that want's to turn the printer on and start printing like a paper printer. For the more technical people, there will be no much time until some make reverse engineering to this machines and start to release mods 🙂
@moinsen40k Жыл бұрын
Moin, there is also a video for the X1?
@247printing Жыл бұрын
Servus! My last video compares the three top printers this year - including the X1C
@Manbo3D Жыл бұрын
Tolles Fazit 👍👌 I agree
@247printing Жыл бұрын
Danke! Hab mich gestern bei dir über Kywoo3d informiert - zuvor nie gehört! Die sind wohl grad im Ausverkauf...
@Manbo3D Жыл бұрын
@@247printing oh ja… die kywoo‘s da ist es sehr ruhig geworden. Leider habe ich auf einige Anfragen bezüglich der IDEX FW kein Feedback mehr von meinem Ansprechpartner bekommen, deshalb kein Teil 2.
@davidwatson4510 Жыл бұрын
Does the P1P use only steel nozzles? Can it use brass nozzles that also fit a CR10?
@Envinite Жыл бұрын
Honestly Prusa did kickstarted the personal 3d printer market, but shot its own leg by barely offering new innovation and just releasing the same thing again and again in different size over the years. Now all they left with are the whole 'open source' thing and its community, but even then, Chinese copy like Ender are slowly taking Prusa target market due to its lower price with similar quality.