Presents three simple steps for installing and aligning a new aftermarket fender. Helps save time and effort when replacing body panels. / @lakesideautobody
Пікірлер: 90
@user-2Hteyasizyc4 жыл бұрын
Right to the point amazing video, not a single bit of useless filler- steps laid out that i woulda never figured out because i dont do body alignments. SO glad i found this.
@LakesideAutobody4 жыл бұрын
Glad it helped - I try to keep the filler to a minimum :)
@OldJoe2124 жыл бұрын
So far you're batting 1.000. What I like best about your videos is no BS, just pure information. Thanks.
@LakesideAutobody4 жыл бұрын
I like no bs too - like in school - just tell me how to do it - give me the assignment - done. Glad you like the videos - have a great week
@tava79022 жыл бұрын
You saved me again. Every time I run into something isn't working out for us. You have it. Never thought of opening the hole a bit. Thank you again.
@LakesideAutobody2 жыл бұрын
That's great to hear. Hope I can keep answering ?s for you :)
@m.jenkins85034 жыл бұрын
My first time here and just in time too. I am trying to help my son with his fender problem, and you show me some great examples that i've never seen before
@LakesideAutobody4 жыл бұрын
Glad to hear it - good luck on your project :)
@kensendelofski37614 жыл бұрын
I always liked the sound of an air rachet. Makes the work go so mach faster. Thanks for the video enjoyed it.
@LakesideAutobody4 жыл бұрын
Glad you enjoyed it :) My dad had an old air grinder and he could make it sound like a car shifting gears. That thing sounded so cool. He passed away and I don't know who ended up with it - it sort of disappeared :)
@DaveDeline2 ай бұрын
Thanks,wind sprung hinge and gap between door and fender too tight.being a extremely windy day wife admitted it door may have been sprung.no big deal but the front hinges are spot welded on from what I see.moving fender forward 2 mil.will solve my issue .glad that the 3 bolt design for fender mounts hasn't changed much .
@LakesideAutobody2 ай бұрын
👍
@sterlingvanhayden79974 жыл бұрын
Pure Gold. Best auto body tutorials on KZfaq...
@LakesideAutobody4 жыл бұрын
Thanks - glad you enjoy them. I'll keep uploading new and different content.
@sterlingvanhayden79974 жыл бұрын
@@LakesideAutobody Thank you...
@austins31532 ай бұрын
Great job
@popatop66578 ай бұрын
If only it were that easy on after market anybody could do it.
@oscargermanalbornozmiliani4 жыл бұрын
Thanks friend, for sharing your knowledge. The explanation is clear, precise and concise.
@LakesideAutobody4 жыл бұрын
You're welcome - have a good weekend :)
@gotredeemed4 жыл бұрын
Outstanding! This what I'm having problems with on a 99 Ram fender. Thanks!
@LakesideAutobody4 жыл бұрын
You're welcome - hope it helps
@miraalnilam95404 жыл бұрын
im having same issue on 1998 ram
@eapauto4 жыл бұрын
Another great one Jerry. Keep them coming.
@jeantaylor67852 жыл бұрын
BEST VIDEO ON KZfaq ON HOW TO DO THIS THANK YOU!!!!
@LakesideAutobody2 жыл бұрын
You're welcome Jean - have a good week my friend :)
@jasongrinnell19863 жыл бұрын
Wow! First video and I found exactly what I needed. Thank you!
@LakesideAutobody3 жыл бұрын
Glad it was helpful!
@absebastians6 ай бұрын
WOW THANK YOU!!!! This is so helpful
@LakesideAutobody6 ай бұрын
Glad it was helpful - thanks for the comment :)
@kurthollyday4214Ай бұрын
Great video
@LakesideAutobodyАй бұрын
Thanks 👍😊
@rw34768 ай бұрын
Very helpful video! Expert advice.
@LakesideAutobody8 ай бұрын
Thanks RW - have a good week :)
@memphis_sean8169 Жыл бұрын
Made it look easy...have to wonder how the factory did it though 🤔
@1951Roy4 жыл бұрын
Excellent advice. Thanks
@jayinmi37062 жыл бұрын
Is the top of the turn signal area on the fender supposed to line up with the bottom of the hood? Is it just because it's an aftermarket part that it doesn't?
@georgeorwell4509 Жыл бұрын
Thanks 👍
@LakesideAutobody Жыл бұрын
👍🛠☺
@jcook69camaro4 жыл бұрын
your hood latch is out of alignment.. the hood moves to the fender when you open it.
@LakesideAutobody4 жыл бұрын
I'll check it out - thanks. Good idea for a video too.
@tree98514 ай бұрын
Doesn't forcing it in with a porta power cause phantom waves that come and go depending on ambient temperature causing metal shrinkage or expansion?
@LakesideAutobody4 ай бұрын
You're actually not bending or distorting the fender - it's just that sometimes you just don't have enough strength to push or pull it - easier with tools like porta powers and come alongs :)
@user-2Hteyasizyc4 жыл бұрын
Helllooo. I have a gap from the door hooking INTO the fender and i highly doubt the door is bent BUT the fender can never be moved over again enough to align the gap in the middle from the bend back of the fender. The fender gap is fine at the bottom and top and gapped quite shitty bad in the middle mostly. If i just get a junkyard fender and repaint it (i know you cant physically see my issue) is it safe to say the door is WAY stronger and most likely the fender will line up fine? Ive done car work for 12 years and been painting for 3 yrs now but I've never done body work other than bondo and sanding my own car and i never assume to be good at autobody work which is a whole new misery for me :) Trying to learn something i cant do easily is not inspiring anymore.
@LakesideAutobody4 жыл бұрын
If I understand correctly - the door pushed the fender in? If that's the case, the cure is to pry that fender back out. Don't be afraid to beat it around to get it in place. If the gap at the top and bottom are good, I would muscle it into place and worry about the damage to the panel later. Rule of thumb: Get the gaps right then fix the damage on the panel. Hope that helps - ask again if not - JV
@user-2Hteyasizyc4 жыл бұрын
@@LakesideAutobody Ok so where the gap is do you mean to PULL THAT gap section TOWARDS the door with a prybar or whatever tool? I've already put my hand behind the fender and made the fender flush with the door again but the middle gap you're saying pull it towards the door right? Sorry its hard to envision though text.
@designsinorbit7 ай бұрын
Hi Jerry. Hope your AMC is going well. My '72 Monte is just about done. What a job. I need to push my front left fender back about 1/4" or less. The fender has never been removed. Do you think it's possible to loosen all the bolts, not remove anything, and move it a smidge? I can't find info anywhere.
@LakesideAutobody7 ай бұрын
It's possible. You might have to gently pry it back somehow without denting it or damaging it. Sometimes you can take out a fender bolt along the hood, lift the fender metal a bit so there's a gap, stick a screwdriver in there and pry it back. You can pry against the bumper, even pull up to a wall and use a jack against the wall to help push it back a bit. Let me know what you end up doing and how it turns out. Enjoy the rest of the week DIO :)
@designsinorbit7 ай бұрын
@@LakesideAutobody Thanks, Jerry! You do the same.
@drwombat10 ай бұрын
Yeah but what about when you DON'T like the gap? How do you approach fit and fitment when it doesn't line up from the rip? Edit: regarding 1:18 ... specifically when it doesn't line up well from the first bolt against the column
@LakesideAutobody10 ай бұрын
If your body mounts aren't rusted, the frame is straight it will always line up - promise. If however, it doesn't, you'll have to use force, That means fender shims, come alongs, porta powers, jacks, hammers, drill bigger holes, etc. You'll have to do what ever it takes to get it to line up. I ran into that exact problem recently and the cab mount was rusted - gone! We jacked up the cab where is was supposed to be, literally welded it in place and the fender gaps were perfect. A new mount would be the best but it was just a truck for fun so....
@drwombat10 ай бұрын
@@LakesideAutobody thank you I'm rebuilding my truck after a low speed front end collision with a newer truck that sits higher (my truck sits factory height for 2wd) and the fever is close... within 1/8 of an inch but it's not congruent on each side (the non wrecked side) and I've never done this before so I'm curious if I should just be happy with that I got and consider it a win that a truck ruled "totalled" by insurance was just pieced back together (no frame damage only cosmetic)
@LakesideAutobody10 ай бұрын
Perfection can be an enemy when it comes to getting jobs done in a body shop. Sometimes you have to accept the best you can do. If it's close, I'd be real happy with it. 👍😊
@XxLetsGetItxX4 жыл бұрын
Thanks for sharing .
@LakesideAutobody4 жыл бұрын
You're welcome - glad you appreciate it
@greighooper52953 ай бұрын
Thanks from the 🇬🇧, ive just boufgt a salvage car the wing is tight on the door after a slight front knock, any advice?
@LakesideAutobody3 ай бұрын
Try loosening the fender bolts and pulling the fender forward or wedging something between the door and the fender while the bolts are loose - then tighten them. Let me know how it goes for you :)
@greighooper52953 ай бұрын
@@LakesideAutobody will do thanks for taking the time to reply to me,
@TrainerTakumi Жыл бұрын
my fender is not lining up with the groove in the middle. it is too high compared to the door. How do I fix that?
@LakesideAutobody Жыл бұрын
First check if the door hinges are "toast". If so, that means the front of the door is low. If that's not the case, sometimes a fender can be bolted into place and bent/pushed down if it is a bit flimsy. Last resort is to smack the mounts down a bit but that's hardly ever the case. Let me know what you end up doing :)
@jeantaylor67852 жыл бұрын
I HAD A FRIEND THATS GOT A JUNKYARD AND I KNOW WERE THE GOODIES ARE I GOT A 95 PASSENGER FENDER OEM MINT WITH THE ROLL UP LIGHT ON IT 40 BUCKS ,
@mikewolfe789 Жыл бұрын
Is there a way to lower the quarter panel an 1/8 by body line on my quarter panel sits higher than my door body line
@LakesideAutobody Жыл бұрын
Was the quarter replaced?
@mikewolfe789 Жыл бұрын
No it was not the door has new bushings and still no luck
@Runescape. Жыл бұрын
ive got a car that was in a collision and the hood hinges were bent, the fender was ripped out, i got my new fender, and new hinges problem is i dont know alignments for any of the initial setup. every thing on the front end is out of alignment, the fenders, the hood, the hood hinges and brackets, and theres no easy way to square them up since the hood hinges are always covered by the fender cowls so you cannot tighten them unless the fenders are off the car. so basically at this point im lost as to where i should begin
@LakesideAutobody Жыл бұрын
When you bolt the hinges to the cowl - w/o the hood or fenders on, do they have any adjustment or are they fixed?
@Runescape. Жыл бұрын
@@LakesideAutobody they have slop in them forwards, backwards and side to side, you are supposed to put each hood hinge in place and then bolt it down. the problem is that the fenders then sit on top of them and block them from being adjusted further, so if you bolt them down, then put fenders on and then put a hood on to check the fitment, you cant adjust anything else beyond that point. its a terrible design and im not sure how i'll fix it.
@LakesideAutobody Жыл бұрын
@@Runescape. Get the hood aligned perfectly with the cowl, then mount the fenders. Or take a look at the old hinges and see where they were bolted (old paint should show) - put them there and forget it. Get the rest of the adjustment out of the top of the hinges that bolt to the hood. Keep asking ?s - we'll figure it out - no worries :)
@IM-nh8hn Жыл бұрын
How can I bend the rear edge of hood down on 02 crv. It’s sitting higher than rear edge of fender. Thanks
@LakesideAutobody Жыл бұрын
If the fender is aligned with the door and you can't adjust it up, and there's no adjustment you can get out of the hinge bolts you'll have to bend it. I actually have climbed up on a chair near the edge of the hood and, starting gently, pushed (bent) it down with my butt to prevent a dented hood :)
@IM-nh8hn Жыл бұрын
@@LakesideAutobody if I put a block of wood underneath the hood where it’s level with fender on that side and try to push down on the rear edge would that work
@LakesideAutobody Жыл бұрын
@@IM-nh8hn That can work, but be careful as the hood may give way as the edge buckles - just give it little compressions like CPR on the rear edge. Good thinking IM :)
@MrRockydee073 жыл бұрын
Thanks for video , I'm doing fenders for the first time both frount fenders for my 2002 Mercury Sable , Are the after Markit ones any good .
@LakesideAutobody3 жыл бұрын
Yes but it's a good idea to take the time to scuff and paint the back side. I believe the factories dip the vehicle in a bath of primer or coating of some type with a the opposite charge of the car so that the primer goes absolutely everywhere. That's why sometimes the original lasts longer than the replacements. Just my thoughts though - not totally sure on that. They always fit well though so... Jerry
@MrRockydee073 жыл бұрын
@@LakesideAutobody Thanks , Yes I'll do the back sides as well also I'm getting the ford primer and paint for cars year but if fenders come primed I'll put more primer on THANKS.
@LakesideAutobody3 жыл бұрын
@@MrRockydee07 You're welcome. If they come primed, all you have to do is check them to make sure everything is coated with the primer they put on, scuff it with a red scuff pad and paint. If there are bare spots, you might want to hit them again to make sure.
@jeremyobanion89942 жыл бұрын
Yeah thanks for the info on the bolts to do first. So none of the other bolts will move the panel correct? I am replacing and painting Metallic Silver for the base. then some metal flak fallowed with some House of Kolor Cobalt candy. Over the silver and flak. It should look sweet. But I need to make sure nothing else will move bend or cause and bowing on the panel. All of the body work must be perfect or it's not worth doing at all. This truck was my late brothers truck and it cost him his pinky finger. So I plan on taking good care of this old girl. next year I will be nickel plating and polishing engine parts. (Nickel won't rust like chrome) And I will be doing 100% of the work myself. I spray some cars when I was 17 to 20 yrs old. But I never replaced parts where I worked it was bondo. But this girl is not getting makeup, She getting the fountain of youth. cant wait to get Caroline on the road. I know my brother would love to see it once I get her done.
@LakesideAutobody2 жыл бұрын
Once you have those three in - that's pretty much where it's staying. The others have to be put in before painting but won't change the gaps. Sorry to hear about your brother. Good luck on your project and let me know how it turns out - would love to see pictures too. Email is under the about tab on the main page - Jerry
@anttisoininen24523 жыл бұрын
What's the manufacturer of that replacement fender? Looks fit good with minor work..
@LakesideAutobody3 жыл бұрын
I'm sorry but I forgot where I got it. I know I purchased it off the internet but can't remember where. I've had very good luck with Chevy replacement fenders though so - I wouldn't worry about it not fitting right - they're right on nowadays.
@anttisoininen24523 жыл бұрын
@@LakesideAutobody Okay, thanks for the answer. On passenger side i have a AP marked fender, that fits quite well, but on the driver side's Tong Yang marked fender didn't fit at all.. So i have to try something else, my options are now classic industries OER or some CHL marked..
@LakesideAutobody3 жыл бұрын
@@anttisoininen2452 That's good to know - thanks for the information. Sounds like classic industries may fit well - but that's just a guess because of the name.
@Treyes92Ай бұрын
How do i align the hood
@LakesideAutobodyАй бұрын
In short put the hood back on in the same "marks" that it was before. You can use body shims to raise or lower certain spots. Push or pull one way or the other. There's more to it so I'll do a video on that very soon as I have to do it soon on a car :)