3D Printed Brushless Motor

  Рет қаралды 280,409

Cool Stuff

Cool Stuff

Жыл бұрын

Hi in this video you'll see how I make this 3D printed DC Brushless Motor. If you like to see a more detailed video on how to make 3d printed motor check out my channel. Thank you for watching.

Пікірлер: 70
@lahanamuhendisi
@lahanamuhendisi Жыл бұрын
Since there is no ferromagnetic material, its efficiency is low and powerless.
@DaProductionsDrawings
@DaProductionsDrawings Жыл бұрын
Please describe ferromagnetic for me if you please
@lahanamuhendisi
@lahanamuhendisi Жыл бұрын
@@DaProductionsDrawings Ferromagnetic materials have very little magnet properties even if there is no source that produces any magnetic field in the environment. When they enter the magnetic field, they show magnetization very quickly. These materials should be used instead of all the plastics used in the video. For example; iron.
@DaProductionsDrawings
@DaProductionsDrawings Жыл бұрын
@@lahanamuhendisi Tanks you
@isminivermekistemeyenmahmut
@isminivermekistemeyenmahmut 9 ай бұрын
​@@DaProductionsDrawingsdemir
@DaProductionsDrawings
@DaProductionsDrawings 9 ай бұрын
@@isminivermekistemeyenmahmut what
@campFTW
@campFTW Жыл бұрын
But sir, there should have been a ferromagnetic core tho 😆
@protadec
@protadec 26 күн бұрын
Hello, may I ask what glue and applicator you use?
@Embassy_of_Jupiter
@Embassy_of_Jupiter Жыл бұрын
I wonder if we'll ever be able to 3D print motors, wires and all in one go. There's these continuous fibre printers, so perhaps it is possible. Perhaps an axial flux motor.
@outbakjak
@outbakjak Жыл бұрын
I'm sure there will be home fabrication machines that can make a motor all in one, but I doubt it would be entirely "printed," although it is possible.. but think about the fact that the coil windings must be densely packed and also coated in something to prevent short circuits. If the machine could switch to a 0.05mm nozzle then back to a standard 0.4mm on the fly, then maybe it could print the "casing" insulation around the coil windings thin enough to have them packed densely enough to be feasible. One thing is for sure: home manufacturing is going to continue growing and becoming much more advanced, giving everyday people means of production that we've never had before. Combine that with AI assisted design, and it's a bright future for hobbyist makers, and the cheapskate diy enthusiast
@SoulAir
@SoulAir Жыл бұрын
What sbout the magnets, can you print magnets?
@Embassy_of_Jupiter
@Embassy_of_Jupiter Жыл бұрын
@@SoulAir probably not, but not all motors need permanent magnets. Mahle for example has recently developed one that would even be suitable for EVs.
@SoulAir
@SoulAir Жыл бұрын
@@Embassy_of_Jupiter Youre right, but I actually looked it up and apparently you can print magnets.
@diminacomusic7070
@diminacomusic7070 10 ай бұрын
i would say it is most likely possible right now. but it would be expensive and no one has a reason to figure out yet. we are kinda doing it in the D.o.D already as you mentioned with a machine similar to the continious fiber. they actually lay the wires down with robots inside of certian planes as they assembly is being printed to house the electronics. when i build commerical plane parts for a Spirit Supplier the only "robot" we had at first wasjust a large drill press that could change sizes and put rivets in the holes without stopping....we did get one that drilled holes before i left...not sure if they ever got it working effectivly... but thats what you get when you send the tech collage kids to the machines instead of the veterans XD...i mean if the engineers actually knew things they were suppose to in that plant it shoulda been a fun new toy to learn.
@user-pg5bs7ud8b
@user-pg5bs7ud8b 15 күн бұрын
it's cool what you've done, i appreciate the work! But if that motor overheats, it will become messy because of the plastic (maybe)
@xa9131
@xa9131 3 ай бұрын
Man I loved science class!!!!
@L_jojovich
@L_jojovich Жыл бұрын
Чел хорош
@Themachinist...
@Themachinist... Жыл бұрын
Sokülemeyen yapıştırıcı kaynak gibi üretimler den kaç
@Screwball70
@Screwball70 6 күн бұрын
Where's the iron bit? I'm no engineer but there's usually an iron bit with the copper windings, don't know why it's there or what it does u just know it's there
@eryavrilio3751
@eryavrilio3751 Жыл бұрын
Can a rf300 motor turned into a bldc?
@LD-technologies
@LD-technologies Жыл бұрын
Cool
@CoolStuff1
@CoolStuff1 Жыл бұрын
Thanks
@tinkerbit
@tinkerbit 6 ай бұрын
Interesting, but the devil is in the datails. It is very difficult to balance.
@zaid-je5es
@zaid-je5es Жыл бұрын
What the size for wire please
@phazyy
@phazyy Жыл бұрын
What type of engineer is most capable of making custom BLDC's? Is there a specific label?
@henrydonaldson4665
@henrydonaldson4665 Жыл бұрын
Probably a team of mechanical and electrical, or just a mechanical who is well researched on electromagnets.
@NormanWray-hi8cu
@NormanWray-hi8cu 23 күн бұрын
Hello dear sir you as to let me learn right over your hands for me to understand exactly how it's as bind wire's thank I'm mr Norman Wray 😊😅
@PORTAL-Gate
@PORTAL-Gate Жыл бұрын
Woow
@fuhadrock6370
@fuhadrock6370 Жыл бұрын
Can you plz tell me your bearing number.... Not diameter.. bearing number.. plz
@leeburrowdotcom
@leeburrowdotcom Ай бұрын
Smooth!
@kfj_7191
@kfj_7191 Жыл бұрын
Nice video
@CoolStuff1
@CoolStuff1 Жыл бұрын
Thanks
@Thatonelacrossedude
@Thatonelacrossedude 10 ай бұрын
I thought you needed soft ware for brushless motors😅
@bernyshomstein9723
@bernyshomstein9723 10 ай бұрын
Looks like just a speed controller wired in.
@ericvauwee4923
@ericvauwee4923 9 ай бұрын
yes, thats what the contorller, the so called ESC does. thats the thing in the yellow heatshrink in the video (note the DC supply but 3 phases). with a ser vo tester you can create a 20kHz PWM signal and by chanign the duty cycle adjust the speed. these are all off the shelf componentens thta are cheap, so you can achieve the same without coding yoursefl, there is code involved on a lower level tho.
@arturceller320
@arturceller320 8 ай бұрын
Only an esc which is hardware.
@ericvauwee4923
@ericvauwee4923 8 ай бұрын
@@arturceller320 and runs software...
@glendajaralve4740
@glendajaralve4740 Жыл бұрын
Is that 30 a esc?
@CoolStuff1
@CoolStuff1 Жыл бұрын
Yes it is
@pavanra7453
@pavanra7453 Жыл бұрын
Hi, i need on of these. Can you make one for me if you are selling these?
@illustriouschin
@illustriouschin 26 күн бұрын
It's like a cave man trying to make a motor. You need more book learning.
@vps6538
@vps6538 7 ай бұрын
Rpm?
@growupjohnny9374
@growupjohnny9374 Жыл бұрын
Music bloooooooooows. Cool motor tho
@shakilmiah1374
@shakilmiah1374 Жыл бұрын
😁😁😁
@As1161712
@As1161712 Жыл бұрын
Muito plástico e pouco ferro
@box420
@box420 Жыл бұрын
That's an ac motor. The esc has a inverter in it than controls the Frequency to change the speed.
@oltro15
@oltro15 Жыл бұрын
People call it a dc motor because thats what comes from the power source. It does switch to ac though
@box420
@box420 Жыл бұрын
@Oltro 15 it's 3 phase ac motor running off of 3 phase ac that comes from a inverter 🤦thats like saying my cars engine is a dinosaur engine because it runs off of dead dinosaurs.
@wojtekdab7760
@wojtekdab7760 Жыл бұрын
But this motor is literally called brushless DC motor
@oltro15
@oltro15 Жыл бұрын
@@box420 Oil is from trees
@Rayblenn
@Rayblenn 6 ай бұрын
Sensorless bldc motor
@yugalsharma13
@yugalsharma13 6 ай бұрын
A magnetic sensor isn't explicitly required. The ESC hardware has the capability to detect the current orientation of motor, from the phase wires itself
@AlejandroFernandezDaCosta
@AlejandroFernandezDaCosta Ай бұрын
if no ferromagnetic core then useless
@techyg321
@techyg321 Жыл бұрын
3 phase Dc.... 🤔 really
@CoolStuff1
@CoolStuff1 Жыл бұрын
Yes... This is an brushless motor that is powered with dc power making it a dc motor.
@Scotch42
@Scotch42 Жыл бұрын
Yes... Really... They are pretty common in the RC world. All DC batteries and speed controllers. They make a digital signal pulsing the electromagnets on and off pulling the rotor round n round.
@xa9131
@xa9131 3 ай бұрын
Well I for one applaud you good man. Everyone seems to forget that it’s all about fun!!! Who cares what applications are for… it’s just a simple project… fun!!!
@CoolStuff1
@CoolStuff1 3 ай бұрын
Thank you 😊
@latinomogapelwa3572
@latinomogapelwa3572 4 ай бұрын
where can i order those materials
@kid_named_fingers
@kid_named_fingers Жыл бұрын
why though
@Ozzy3333333
@Ozzy3333333 Жыл бұрын
Horrible efficiency design
@arcanelegends-td9co
@arcanelegends-td9co 13 күн бұрын
lol bad idea
@project-hobby
@project-hobby Жыл бұрын
It's not dc
Dry vs Moist TPU in 3D Printing
1:00
PrintMeister
Рет қаралды 456 М.
Crazy High RPM Fan 😱 wait for Results #shorts #viral
0:40
WRANGLER VILLAGER
Рет қаралды 12 МЛН
ОДИН ДЕНЬ ИЗ ДЕТСТВА❤️ #shorts
00:59
BATEK_OFFICIAL
Рет қаралды 7 МЛН
Homemade Professional Spy Trick To Unlock A Phone 🔍
00:55
Crafty Champions
Рет қаралды 58 МЛН
ИРИНА КАЙРАТОВНА - АЙДАХАР (БЕКА) [MV]
02:51
ГОСТ ENTERTAINMENT
Рет қаралды 5 МЛН
How to Make a Brushless Motor / 3D Printed Brushless Motor
7:11
Which 3D Printing Filament to Use For What
0:59
The Next Layer
Рет қаралды 31 М.
Electromagnetic Train #Short #maglev #maglevtrain #magnetictrain
0:39
600 Watt, 3d-printed, Halbach Array, brushless DC electric Motor
6:25
Christoph Laimer
Рет қаралды 590 М.
DIY 18650 Liion Battery Charger using TP4056
0:24
ErCan Everything
Рет қаралды 10 МЛН
How to make brushless motor at home | #shorts
0:57
The DC Experiment
Рет қаралды 267 М.
Let me show you (P1)
0:21
Discovery Boy
Рет қаралды 2,4 МЛН
ААААА СПАСИТЕ😲😲😲
0:17
Chapitosiki
Рет қаралды 3,6 МЛН
это самое вкусное блюдо
0:12
Katya Klon
Рет қаралды 2,1 МЛН
Pedro 😰😰😰😰😰
0:59
Jane & Sergio 🥰
Рет қаралды 69 МЛН
My little bro is funny😁  @artur-boy
0:18
Andrey Grechka
Рет қаралды 4,2 МЛН