3D Printed RC Boat Build! Biggest Project So Far!
Рет қаралды 20,531
Күн бұрын3D Printed RC Race Boat!
This is a fun project. I did a test run and it was fast and fun. Unfortunately it was windy and choppy so I did not get a good video. I will release a test run video after the winter!
0:00
0:15 Finding the STL
0:36 3D Printed Parts
0:53 Sanding and Gluing the Parts
2:49 Prepping Surface for Paint
3:27 Glazing Putty
3:59 Epoxy Coating
5:29 After Epoxy Coating Has Cured
5:44 Filling Imperfections Before Paint
6:49 Hardware
7:04 Measuring for Motor Mount
7:33 Drill Hole for Drive Shaft
7:51 Install Rudder Assembly
8:23 Epoxy Drive Shaft in Place
8:31 Prep Surface for Motor Mount
8:42 Epoxy Motor Mount in Place
8:59 Install Servo
9:08 Finished Boat Ready for Test Run
9:26 First Test Run Coming Soon!
STL can be found here: www.thingiverse.com/thing:245...
Designed by thepael
Parts I used -
Brushless Motor & ESC: www.amazon.com/dp/B095GNR1N2?...
Flex Collet: www.amazon.com/dp/B09K3HGTZ5?...
Propeller: www.amazon.com/dp/B07JQL6LYY?...
Lipo Batteries: www.amazon.com/dp/B07Y56XHMK?...
Rudder & Drive Shaft: www.ebay.com/itm/173865062345
Motor Mount:www.ebay.com/itm/222902551317...
@Shinobi117 Жыл бұрын
Fantastic. Great job
@bchobby Жыл бұрын
Thank you!
@jean-philippepimentel5108 Жыл бұрын
Beautifull work!
@bchobby Жыл бұрын
Thank you!
@corbymodelboatclub Жыл бұрын
Nice one. Just printing the same boat. Some good tips, thanks.
@bchobby Жыл бұрын
It is a fun build!
@SoloCrimeWave 9 ай бұрын
Turned out really nice. Good job!
@bchobby 9 ай бұрын
Thank you! It was a fun project. Working on another one now.
@Zeusifer123 Жыл бұрын
great job!
@bchobby Жыл бұрын
Thank you!
@rcnortechboats 3 ай бұрын
You make good job.
@bchobby 3 ай бұрын
Thank you!
@mohdfaizalajun_tv Жыл бұрын
I really enjoyed this video... greetings and support again my friend👍good
@bchobby Жыл бұрын
Thank you!
@Vdbdesigns-3dprint Ай бұрын
just printed and assembled the boat. do you have the measurements where you drilled the home for the shaft? im not into rc boats at all, so have no starting point.
@billjonesnation Жыл бұрын
Nice build! I have a similar build on my channel with the jet boat from thingiverse. I didn't use any resin to cover my boat but in hindsight maybe I should have. Did it add noticable strength ? Are you worried the resin will separate and crack off the plastic or does it bend enough not to do that?
@bchobby Жыл бұрын
Thank you! It was my first 3D printed boat. I just know PLA will absorb water so I wanted to coat it. I have seen others coat it in carbon fiber. As for it delamination I have not had any problem yet. Waiting for winter to end before I can do some real testing.
@bchobby Жыл бұрын
Your channel looks awesome! I just subscribed.
@billjonesnation Жыл бұрын
@@bchobbyThanks. I did the same. I look forward to your next builds.
@05_caoquangbach21 19 күн бұрын
What glue do you use to glue the boat parts together ?
@704zombie Ай бұрын
How this did you make your walls. I just finished printing mine and worried to sand a lot on it I made mine 1.2mm thick
@bchobby Ай бұрын
I will have to check my files. I can't remember off the top of my head.
@jonabernathy3227 9 ай бұрын
Looks Great? What did you use to mount your servo and ESC?
@bchobby 9 ай бұрын
Thanks! I just used Velcro to mount them both. That way I can easily remove them when needed. I also swap them into other projects sometimes.
@JusRc Жыл бұрын
Awesome but where did you find the file for the trailer??
@bchobby Жыл бұрын
Thanks! I got it on cults3d. I had to modify the length a little bit. Here is the link. cults3d.com/en/3d-model/various/blackjack-catamaran-boat-trailer
@bchobby Жыл бұрын
I have a build Video of the trailer coming soon. But the designer has great documentation.
@daiciuapostol79 Жыл бұрын
Great project,if you whill build another one put one layer of fiberglass or carbon inside not only resin,and maybe twin motors whill be nice🙂
@bchobby Жыл бұрын
Thanks for the tips! I am going to build a bigger one next. Dual motors for sure!
@daiciuapostol79 Жыл бұрын
@@bchobby believe me it whill be something amazing,I hit the🛎
@daiciuapostol79 Жыл бұрын
@@bchobby kzfaq.info/get/bejne/o6ylpsV4p8rUZYU.html that's a twin 😉
@bchobby Жыл бұрын
That is awesome! I just subscribed. Very cool channel!
@daiciuapostol79 Жыл бұрын
@@bchobby thanks,yes a nice hobby I like to build my boats🙂
@zaneshaw7913 9 ай бұрын
What would you charge for a 46" cat hull with canopy shiped in pieces ready to assemble?
@tiinorivera7606 3 ай бұрын
Hmu
@douggordon3096 Жыл бұрын
Will you print for customers
@bchobby Жыл бұрын
I am not sure it would be very cost effective for the customer but it is possible.
@alexiapostolopoulos5374 8 ай бұрын
Is there 24” STL file for the Blackjack 24-Inch Catamaran Brushless: R?
@bchobby 6 ай бұрын
I am not sure if there is a 24" version. You could probably just scale it down in the slicer.
@sgeier1883 5 ай бұрын
I omitted one section to make it shorter
@PlancksTime 11 ай бұрын
Ur boat is gonna explode, it looks really weak
@bchobby 11 ай бұрын
I have about 10 batteries through it so far. No problems whatsoever. If it does break I will build a new version tougher next time.
@TheGreatBooger 11 ай бұрын
@@bchobbynot sure how it looks weak, you coated it with epoxy, same way full scale cigarette boats do. Lol 😂
@bchobby 11 ай бұрын
@@TheGreatBooger I agree haha! I am no expert though. This is my first attempt at a 3D printed RC boat.
@ringerdiggsycobbsy6254 9 ай бұрын
Didn't mind the video except there's no talking and it just stupid music
@bchobby 9 ай бұрын
Thanks for the feedback!
@NowWattFPV 7 ай бұрын
So lame.
Bernard Dostie
Рет қаралды 88 М.
BalcevMMA_BOXING
Рет қаралды 16 МЛН
Craft Channel
Рет қаралды 221 М.