No video

3D Printer Silence Mod | AnyCubic i3 Mega

  Рет қаралды 2,429

Sam Campbell

Sam Campbell

Күн бұрын

If you're interested in making your AnyCubic i3 Mega quieter as well I've linked some useful resources below to go along with this video:
www.pialasse.c...
kore.cc/i3mega...
Music Credits:
Wintergatan - Starmachine 2000
Wintergatan - Sommarfågel
TIMESTAMPS:
0:00 - Introduction
2:21 - Fan Upgrades
9:43 - Motor Controller Upgrades
12:58 - TMC2209 Voltage Tuning
15:54 - Noise Tests
17:00 - SD Card Repair
18:00 - Conclusion
_________________________
Sam Campbell or "The Modding Room" makes no representation about the accuracy, reliability, completeness, or legality of the activities, techniques or modifications shown in this video or the results to be obtained therefrom. If you choose to engage in any activities described in this video, you could potentially void any warranty you may have on the equipment or software you use. Your actions could also be in violation of certain provisions of the agreements you have with the manufacturer(s) of the equipment or software you use. You are solely responsible for adhering to any intellectual property laws and usage restrictions applicable to such products and any other products you may use.
Under no circumstances will Sam Campbell or "The Modding Room" be responsible for any loss or damage, including personal injury or death, that may result from your engagement in the activities demonstrated in this video. You also assume all risk and liability that may result from your engagement in such activities

Пікірлер: 3
@GSling-gn6zn
@GSling-gn6zn 10 ай бұрын
Good mods for this line of printers. You should look into getting a Pi4 and convert to Klipper firmware (relatively easy and reduces print times). If you do, then you can install a touch probe and setup UART mode for even finer refinement (your board will probably be a clone Trigorilla board) for those drivers as well as remote print like your current firmware. Did that with my Mega X and its night and day from stock.
@jusyoniox
@jusyoniox Жыл бұрын
Glad you're back!
@chris_topher1984
@chris_topher1984 Жыл бұрын
i wish i had local friends like you. nobody i know finds electronics and gaming interesting.
Anycubic Mega S Cable Chain Full Guide | Print This Next
20:30
JJ Shankles
Рет қаралды 32 М.
لااا! هذه البرتقالة مزعجة جدًا #قصير
00:15
One More Arabic
Рет қаралды 50 МЛН
My Cheetos🍕PIZZA #cooking #shorts
00:43
BANKII
Рет қаралды 22 МЛН
Survive 100 Days In Nuclear Bunker, Win $500,000
32:21
MrBeast
Рет қаралды 147 МЛН
Anycubic Mega X TMC2208 Upgrade - Silence!
18:26
The Real Sam Prentice
Рет қаралды 12 М.
This printer is OLD. Why is it still my favorite?
13:56
Made with Layers (Thomas Sanladerer)
Рет қаралды 152 М.
Обзор Anycubic Mega X
14:21
K3D tech // Dmitry Sorkin
Рет қаралды 46 М.
Anycubic i3 Mega Ultimate Upgrade Guide
9:16
Modern Hobbyist
Рет қаралды 70 М.
Anycubic i3 Mega 3D Printer Review ✰
10:17
Make Anything
Рет қаралды 175 М.
Замена драйверов на 2209 (Anycubic i3 mega)
11:24
Must have extruder upgrade for Anycubic Mega 3d printer.
16:10
Volodymyr Zhadlun
Рет қаралды 1,4 М.
Anycubic i3 Mega TMC2208 Silent Mod
3:34
LOHTEC
Рет қаралды 84 М.
لااا! هذه البرتقالة مزعجة جدًا #قصير
00:15
One More Arabic
Рет қаралды 50 МЛН