3rd brake light replacement repairing. Renault Scenic

No video

3rd brake light replacement repairing. Renault Scenic

Рет қаралды 31,229

Күн бұрын

Video tutorial: how to repair the 3rd brake light of your car.
It is not normally necessary to replace it.
By using a standard 12V led strip you can save money for replacement.
The video shows a renault scenic III series, but the procedure is similar for many other cars.
If you like these kind of video, please subscribe!
00:00 Introduction
00:36 3rd brake light removal
02:17 brake light connector test
02:33 brake light repairing
07:00 reinstallation
08:05 final test
#brake #scenic #carrepair
"Saving with DIY" is a youtube channel that aims to show how, on our own, we can carry out projects, create devices, repair objects, but also make INVESTMENTS ... making a profit or saving money!

Пікірлер: 31

@hilariovalerovalero1581 3 ай бұрын

Hola, aparte de lo que ha hecho Saving que me parece estupendo, yo lo que hice es lo que se ha hecho siempre, sacar un cable del positivo del piloto de la bombilla del freno ya puede ser del piloto izquierdo ó derecho y llevarlo al positivo del piloto central por dentro de la goma del portón para que no se vea, el cable negativo te vale el mismo que tienes del piloto central y solucionado

@crislopez3884 Жыл бұрын

Dobra robota 👍

@musasimsek9644 Жыл бұрын

Çok teşekkürler bu paylaşımınız icin

@AzerothMyst 5 ай бұрын

Thank you 🎉

@marouanemazi6651 Жыл бұрын

شكرا جزيلا على الشرح الرائع 😍😍😍

@hilariovalerovalero1581 3 ай бұрын

Creo que el cable positivo del piloto de freno trasero izquierdo que yo hice era de color rosa y se empalma al cable que pones positivo del piloto de freno central. Gracias Saving por el video

@Zamani_Hidayah 7 ай бұрын

2:22 check the current reaches or check the voltage?

@mustafaaygun4566 Жыл бұрын

The leds used to replace, should be SUPER RED type(not only red). If not it seems like whitely... Orjinal is osram super red leds... Like laser red....

@luizmauriciomarques350 10 ай бұрын

blz show

@jacinpascscudr5643 Жыл бұрын

Hello good morning. Have you done something on the board before placing the led strip? I mean, if you've overridden something, or removed any components. Thank you very much for your input

@savingwithdiy2844 Жыл бұрын

Hello. Actually I don't remember, because I made the strip led chenge few years ago. Then, after some years I replaced it again and I decided to make the video. But, if I remember well, you can stick the new strip led on the original one. The work is quite easy. I didn't find specific problems, and you can save some money 😉

@a.cotrimluis7580 3 ай бұрын

🔝👌🇵🇹

@user-nb5nm4ol8p Жыл бұрын

Renault Megane 3: Led Strip with 1KOhm resistor in parallel worked for me

@ClaudioKhmer Жыл бұрын

Could You please explain how to do it? In my Renault scenic xmod I've removed all components and glued the red strip as in the movie. If I power it with a 9V battery it works, but it is not working on the car. The car voltage measured is 8V.

@hilariovalerovalero1581 3 ай бұрын

@@ClaudioKhmer Hola, yo lo que hice es lo que se ha hecho siempre, sacar un cable del positivo del piloto de la bombilla del freno ya puede ser del piloto izquierdo ó derecho y llevarlo al positivo del piloto central por dentro de la goma del portón para que no se vea, el cable negativo te vale el mismo que tienes del piloto central y solucionado

@lifeplumbingrv8211 4 ай бұрын

❤🇺🇦

@rafaelgonzalezsancho7591 Жыл бұрын

Si muy bien, eso mismo lo hice yo y no reconoce el cambio del vehículo los leds, no funciona de ninguna manera.scenic

@hilariovalerovalero1581 3 ай бұрын

Hola, yo lo que hice es lo que se ha hecho siempre, sacar un cable del positivo del piloto de la bombilla del freno ya puede ser del piloto izquierdo ó derecho y llevarlo al positivo del piloto central por dentro de la goma del portón para que no se vea, el cable negativo te vale el mismo que tienes del piloto central y solucionado

@bomba4 Жыл бұрын

Please, refresh Seal.. Or it will take rainy..

@weaselstoat Жыл бұрын

Hi for anyone trying this I wanted to give my experience so far - i did the mod and the light works when powered by a power supply, however when on the car it does not light up but flickers slightly when the brake pedal is first pushed down. I am getting a constant 8.5v on the socket so I am not sure how it is controlled to turn on and off but in any case it never turns on, only flickers at the pedal is pressed. I noticed someone else mentioned using a 1KOhm resistor in parallel, perhaps that is the solution but im absolutely clueless as to how the one in the video works (i dont see any resistor, just strands of wire connecting) and mine doesnt! Lots of people seem to have the same issue but nobody has posted if they actually got it to work.

@savingwithdiy2844 Жыл бұрын

actually I didn't face your problem. I used a standard strip led 12V and it worked without any resistor. I'm sorry for it. My be the stri led has the resistors inside

@weaselstoat Жыл бұрын

@@savingwithdiy2844 thanks for the quick reply - just done some testing, so for anyone who has done the mod and it still doesnt work, the solution is a resistor in parrallel (solder one end to positive terminal and the other to negative on the LED board) - a 1KOhm should be the right resistor - i had a couple of random ones, a 4.7k which was way too big and immediatley got hot and a 2k which does get a little warm but seemed OK after testing for a couple minutes - i will order a 1kOhm and replace to be on the safe side.

@lennycook206 9 ай бұрын

So when I add my led cut down strip, the new strip lights up all the time. There is always 8v at the plug? Will the resistor help with this? Or does it mean I have another problem? My original was badly damaged and even worse repair by previous owner. But my main 2nbrake lights work perfectly so I don't think it's a switch issue in pedal

@hilariovalerovalero1581 3 ай бұрын

@@lennycook206 Hola, yo lo que hice es lo que se ha hecho siempre, sacar un cable del positivo del piloto de la bombilla del freno ya puede ser del piloto izquierdo ó derecho y llevarlo al positivo del piloto central por dentro de la goma del portón para que no se vea, el cable negativo te vale el mismo que tienes del piloto central y solucionado

@bernard8267 6 ай бұрын

I thanks very interesting video, can you confirm that the input voltage is 8.5 volts as in the video ? I made the replacement with the 12 V Led every went right, all the test have been OK up to the install on the car, the light flashed and stop, at the beginning and at the end of the break, thanks for the return

@Andrej71 2 ай бұрын

Have you fixed it