No video
4L60E: AFL Valve (Part 1) How it Works
Рет қаралды 17,185
2 жыл бұрынLearn how the 4L60E AFL Valve works. When there are problems with the Actuator Feed Limit (AFL) circuit, it leads to number of 4L60E problems; smoked clutches, wrong gear starts, neutrals on Hwy, etc.
Before we can address the problem areas, it's important to first understand the basics of how a healthy system works. Buckle up!
Help this Channel Grow: • Help This KZfaq Chan...
**More 4L60E Videos**
Pump: • 4L60E Pump: How Does I...
PR Valve (Part 1): • 4L60E Pressure Regulat...
PR Valve (Part 2): • 4L60E Pressure Regulat...
PR Valve (Part 3): • 4L60E: PR Valve (Part ...
1-2 Shift Valve + Solenoid (Part 1): • 4L60E: 1-2 Shift Valve...
1-2 + 2-3 Shift Solenoid (Part 1): • 4L60E Shift Solenoid -...
Planetary Gearset: • Planetary Gearset - Ho...
Power Flow (OD Gears): • 4L60E Power Flow (1st,...
Power Flow: (Manual Gears): • 4L60E Power Flow - Man...
Teardown: • 4L60E Rebuild: Teardow...
Teardown Time-Lapse: • 4L60E Teardown (TimeLa...
Output Shaft Swap (2WD to 4WD Conversion): • 4L60E Output Shaft Swa...
RESOURCES:
1) 4L60E Tools: (Paid Links)
Electrical Harness Case Connector Tool: amzn.to/3uJeqXZ
Torx Plus Bit/Socket: amzn.to/3l4Ad8X
Teflon Seal Ring Installer (Sizing Tool Kit): amzn.to/3BWwQZP
Shift Shaft Seal Puller/Installer: amzn.to/2Oa2sat
Universal Transmission Pump Puller: amzn.to/3t7uDFH
3-Ton Arbor Press (12 inch working height): amzn.to/2Reqmyx
Lip Seal Installer: amzn.to/2Gz4KI5
Lip Seal Installer (Huge Time/Headache Saver): amzn.to/2MxUC8O
Pump Alignment Band: amzn.to/2J13lNF
Universal Clutch Spring Compressor (Use in trans & drums): amzn.to/2YHQGn6
Adjustable Clutch Spring Compressor (Use with shop press): amzn.to/2W2DAQs
Universal Bushing Driver Kit (Larger Sizes): amzn.to/2M1aQHn
Universal Bushing Driver Kit (Smaller Sizes): amzn.to/2Et1ON3
Snap Ring Pliers (Clutch Spring Compressor Snap Ring): amzn.to/2GwwixP
Snap Ring Plier Set (Pump Circlip Snap Rings): amzn.to/2IUxpdu
2) 4L60E Parts: (Paid Links)
Over-Sized Pressure Regulator Valve: amzn.to/3CbAHm1
0.500" Boost Valve: amzn.to/3Af6ccP
Bell Housing Bolts (Torx): ebay.us/vZLBiN
Pan Gasket (Fiber): amzn.to/2N4Ykba
Filter: Shallow Pan: amzn.to/3t7AtH7 Deep Pan: amzn.to/30sVoYL
Output Shafts:
Heavy-Duty: 2WD: amzn.to/3dxjw4q. 4WD: amzn.to/2NRN9m0
Standard-Duty: 2WD: amzn.to/3pKoptk 4WD: ebay.us/cDwiJt
Rebuild Kit: 93-03: amzn.to/3chb3Qw 04-Up: amzn.to/2OaYJcL
Molded Pistons: amzn.to/3chRbNb
2-4 Band: Stock: amzn.to/3rvW2ke Hi-Perf: amzn.to/2N3JRw2
Sun Shell: Upgrade: amzn.to/3cbPmRK Heavy-Duty: amzn.to/3rzAEuv
3) Safety-Wear: 😷 (Paid Links)
A) Comfortable Safety Glasses: amzn.to/2JguhZN
B) Work Boots: amzn.to/2GD9eP7
C) Nitrile Gloves: amzn.to/2Y6XwSN
4) Tools: 🔧 (Paid Links)
Craftsman 230-Piece Tool Set: amzn.to/2L0AtWv
1/2 Impact Gun (Ingersoll Rand): amzn.to/30zUuHA
3/8 Impact Gun (Ingersoll Rand): amzn.to/30l5gpm
Air Compressor (60 Gallon)(Ingersoll Rand): amzn.to/2QkisXt
1/4 Air Hose (Flexzilla): amzn.to/2QjJQ7W
Pocket Screwdriver: amzn.to/2OdoR44
Spring-Loaded Center Punch: amzn.to/304x3dx
Yellow Paint Pen: amzn.to/2LZRQWq
Brass Punch: amzn.to/2QlSAe1
Bench Vice (Craftsman): amzn.to/2LFnKbZ
5) Shop Supplies: ✏️ (Paid Links)
Thread Locker: Medium: amzn.to/2YLtmFk Heavy:
Brake Parts Cleaner: amzn.to/2HxQ1Pz
DISCLOSURE: 🕵
Links provided are affiliated links with the associated websites. While there is no extra cost to the purchaser, a small portion of the sale goes to support this KZfaq channel.
@SouthpawAutoworks 2 жыл бұрын
Thank you for being here! If it feels right to you, help me spread the word about this channel… 1 Handed Transmission Rebuilder (60 sec): kzfaq.info/get/bejne/kLd4p9WHq7uslJ8.html
@markgriffin847 2 жыл бұрын
You are the best transmission guy on KZfaq. Thanks
@SouthpawAutoworks 2 жыл бұрын
What a compliment! Positive feedback is always appreciated. Thanks for dropping me a line!
@1970chevelle71 2 жыл бұрын
The animation used to illustrate the fluid path and the valve movement is absolutely the best I have ever seen! From a semi retired GM tech who has nearly every GM book on the 4l60 and the 4l60E in my library.
@SouthpawAutoworks 2 жыл бұрын
Right on! The feedback is appreciated. Thanks for dropping me a line!
@philipwilliams6648 2 жыл бұрын
I am a retired autobody tech with extensive experience in mechanical repair tho very limited to the modern transmission, you nailed it with the info put forth. I wish alone of the ICar classes and instructors would present the information in a manner such as you. Your way of instruction should be used by the automotive industry should be used. You present in a very precise manner. I have been an instructor in the past and can say without a doubt GREAT JOB
@SouthpawAutoworks 2 жыл бұрын
Wow, what a compliment!! I really appreciate you taking the time to write what you wrote. Much appreciated. Thanks for dropping me a line! PS - If it feels right to you, please help me spread the word about this channel. 1 Handed Transmission Rebuilder: (60-Sec Preview) kzfaq.info/get/bejne/r5mGnNuSxKvHYXk.html
@TheBry_Guy 8 ай бұрын
Great information. troubleshooting my 4t65E and had no grasp of the terms I was being told. this explains SO much.... Thanks!
@SouthpawAutoworks 7 ай бұрын
Great to hear! Thanks for dropping me a line.
@brandonrogers6855 6 ай бұрын
I thoroughly enjoy watching and learning from you. You are a great teacher and have dinner a great job with your videos. You explain everything so brilliantly. I want to thank you personally for all of your hard work and time that you have poured into these videos. God Bless your soul. I have learned so very much from you and now I know that I am armed with great knowledge that I can use throughout the rest of this journey we call life and I will make sure that I pass this knowledge on to others as you have done so wonderfully. I can't say thanks enough!! 🙂
@SouthpawAutoworks 6 ай бұрын
So glad you enjoyed the video. Thanks for dropping a line.
@joshuayoung6286 2 жыл бұрын
Really appreciate your videos. There is plenty of how to videos on the 4l60e’s but they rarely explain why. Thanx!
@SouthpawAutoworks 2 жыл бұрын
The positive feedback is appreciated. Knowledge is power... Thanks for dropping me a line! PS - If it feels right to you, please help me spread the word about this channel. Here's an easy way to share... 1 Handed Transmission Rebuilder: (60-Sec Preview) kzfaq.info/get/bejne/r5mGnNuSxKvHYXk.html 60-Second Preview of the video you just watched: kzfaq.info/get/bejne/r8yIl9tnptHVmok.html
@natedillard7353 Ай бұрын
That circuit is always worn out , valve and bore . Burns up alot of clutches … Great video , learned a lot man !
@SouthpawAutoworks Ай бұрын
Right on! Appreciate your comment.
@basicdetail4512 10 ай бұрын
Thanks so mutch brothers i appreciate your work
@andrewballance4161 Жыл бұрын
Stuff like this just makes my day. Thanks
@SouthpawAutoworks Жыл бұрын
Your comment makes my day. Thanks for dropping me a line!
@voidisyinyangvoidisyinyang885 Жыл бұрын
stunning - AFL valve vid. thanks
@SouthpawAutoworks Жыл бұрын
Glad you enjoyed it. Thanks for dropping me a line!
@hosalabad Жыл бұрын
Great video, the animations are fantastic for explaining the flow.
@SouthpawAutoworks Жыл бұрын
Glad to hear that! Thanks for dropping me a line!
@fildavis2024 2 жыл бұрын
Wow! Super informative video! That’s a ton of work you’ve done to explain that. Gunna check out the video you recommended at the end. 👍
@SouthpawAutoworks 2 жыл бұрын
Awesome, thank you!
@joserodriguez2632 Жыл бұрын
Excelent information, so far the best transmision tutorial in KZfaq channel. Thanks for sharing.
@SouthpawAutoworks Жыл бұрын
Glad you enjoyed it! The positive feedback is appreciated. Thanks for dropping me a line!
@user-te5xf5ir4f 2 жыл бұрын
I just love so much how you explain and illustrate. The info you give is gold. Besides the stock application, after you explain everything for some part, i would like to hear about mods that people do and how it changes stuff. For example : Stiffer springs in boost valve, Adding 1 more spring in the AFL valve
@SouthpawAutoworks 2 жыл бұрын
Glad you enjoyed it! I plan on creating follow-up videos that cover common problems, and solutions for each of those problems. I'd be happy to also cover mods and how it affects the system. Thanks for dropping me a line! PS If you're interested in spreading the word about this channel...here's an easy way to share. Roughly 60-second video... 1 Handed Transmission Rebuilder: kzfaq.info/get/bejne/g9ymaKaVl8m6h2g.html
@maxt3592 2 жыл бұрын
Thank you for this information very informative looking forward to watching some other videos
@SouthpawAutoworks 2 жыл бұрын
You're welcome. Thank you for taking the time to drop me a line! PS - If it feels right to you, please help me spread the word about this channel. Here's an easy way to share... 1 Handed Transmission Rebuilder: (60-Sec Preview) kzfaq.info/get/bejne/r5mGnNuSxKvHYXk.html How the 4L60E valve-body works: (60-Second Preview) kzfaq.info/get/bejne/nL2AhsR9yseziH0.html
@MagnomRock 2 жыл бұрын
Superb explanation. Excited for your channel to snowball with views; in anticipation of your following videos!
@SouthpawAutoworks 2 жыл бұрын
Thanks for checking it out! I'm glad you're here... I'm excited to get more people involved with automatic transmissions. Thanks for dropping me a line!
@PHLTHS Жыл бұрын
These videos are so amazing, Thank you for taking the time to create there. There's nothing as good as these on KZfaq. Cheers fella.
@SouthpawAutoworks Жыл бұрын
Glad you like them! I really enjoyed making this video. More to come!
@Crimsonengine 2 жыл бұрын
Looking great as usual!
@SouthpawAutoworks 2 жыл бұрын
Thanks, man! Really appreciate you stopping by.
@dreece2000 2 жыл бұрын
cant wait for part 2
@SouthpawAutoworks 2 жыл бұрын
Right on. Thanks for dropping me a line!
@brianworkman1959 7 ай бұрын
I did hydraulic circuit identification and mapping back in 1988 starting with ZF4hp-22 Nice computer automation
@SouthpawAutoworks 7 ай бұрын
Right on! Thanks.
@jordanraynard7120 Жыл бұрын
Amazing job, doing my last year of school as an auto tech and this helped huge! thank you!
@SouthpawAutoworks Жыл бұрын
Right on!! That's exciting! Thank you for dropping me a line.
@fkyrmhr0650 Жыл бұрын
You are amazing 👏 thank you for all your content
@SouthpawAutoworks Жыл бұрын
It's a labor of love. Thanks for dropping me a line.
@kenchaffin4946 Жыл бұрын
Great job
@SouthpawAutoworks Жыл бұрын
Thank you, Ken.
@colchilibeck 2 жыл бұрын
Hey man, amazing video! Congrats on starting a channel that will only grow!
@SouthpawAutoworks 2 жыл бұрын
Glad you enjoyed it. Thanks for dropping me a line! Much appreciated. PS - If it feels right to you, please help me spread the word about this channel. 1 Handed Transmission Rebuilder: (60-Sec Preview) kzfaq.info/get/bejne/r5mGnNuSxKvHYXk.html How the 4L60E valve-body works: (60-Second Preview) kzfaq.info/get/bejne/nL2AhsR9yseziH0.html
@archibongedem9968 9 ай бұрын
Thank you so much for this video, it taught me a lot today
@SouthpawAutoworks 9 ай бұрын
Right on!!
@joeberg9823 Жыл бұрын
What an absolutely awesome video. Thank you! I came here to watch this because of a 4t65e transmission and how it is always suggested to replace the AFL valve with an updated sonax/superior part. I now completely understand what this valve actually does and why this part wears out from moving so much and why it is recommended to ALWAYS replace it when inside the transmission. I assume it works the same way in the GM 4t65E (hopefully). Thanks again for the time and effort put into these videos!
@SouthpawAutoworks Жыл бұрын
It will work the same way (4L60E vs 4T65E). Glad you enjoyed the video, and got value out of it. Always nice to watch something, and it be worth your time....not always the case on KZfaq. Thank you for taking the time to drop me a line, Joe. The positive feedback is appreciated.
@20havenfun08 2 жыл бұрын
Thank you so much.... I don't build transmissions, but you make it so interesting.....
@SouthpawAutoworks 2 жыл бұрын
Glad you enjoyed it! It's not too late to start... ;) Thanks for dropping me a line! PS If you're interested in spreading the word about this channel...here's an easy way to share with friends, family, FB Groups, automotive forums, etc. (Roughly 60-second video) 1 Handed Transmission Rebuilder: kzfaq.info/get/bejne/g9ymaKaVl8m6h2g.html
@henrymvillarl6895 4 ай бұрын
Thanks You from Venezuela 🇻🇪
@SouthpawAutoworks 3 ай бұрын
Right on. You're welcome.
@10malabdullah10 9 ай бұрын
Thank you the time you spend to create educational videos for everyone
@SouthpawAutoworks 9 ай бұрын
My pleasure.
@toddphillippi3461 2 жыл бұрын
I admire your dedication! Lots of work to edit videos. I’ll be checking out the others too.
@SouthpawAutoworks 2 жыл бұрын
Right on. Thanks for dropping me a line!
@FilterYT 6 ай бұрын
Excellence! Thanks again.
@SouthpawAutoworks 6 ай бұрын
Glad you enjoyed it! Thanks for dropping me a line.
@codyd0g 2 жыл бұрын
Robert.... we like the video! You’re amazing... talented! So let’s see some of your amazing guitar work next.
@SouthpawAutoworks 2 жыл бұрын
Dana!!! I was just thinking about you and Gary, earlier this week. And boom....here you are. Crazy how that works. =) I'm gonna DM you!
@cenick7254 Жыл бұрын
Hi , There is no one to explains like You . ( 👍 * 1000 ) with the best regards
@SouthpawAutoworks Жыл бұрын
Wow, thank you!
@bryanchambers8868 2 жыл бұрын
Thank You
@SouthpawAutoworks Жыл бұрын
You're welcome. Thanks for dropping me a line!
@toodrunktotastethischicken 2 жыл бұрын
Hey man, you have a unique way of presenting the tech info in this video compared to even ATSG/ATRA. They need to take a page from your book. Keep up the good work.
@SouthpawAutoworks 2 жыл бұрын
I've got a lot of respect for ATSG & ATRA...so that means a lot. Thank you kindly. Thanks for dropping me a line! PS - If it feels right to you, please help me spread the word about this channel. 1 Handed Transmission Rebuilder: (60-Sec Preview) kzfaq.info/get/bejne/r5mGnNuSxKvHYXk.html 4L60E AFL Valve - Part 1: (60-Sec Preview) kzfaq.info/get/bejne/r8yIl9tnptHVmok.html
@SouthpawAutoworks Жыл бұрын
I'm scrubbing through past YT comments, looking for something...and I came across your comment. Thank you, again, for what you wrote. It is appreciated.
@rakeshminj7024 Жыл бұрын
Very nice and informative video. It takes lot of effort and creativity to create such kind of detailed and easy understanding content to explain in such small length video. Keep doing this good work. Thank you !
@SouthpawAutoworks Жыл бұрын
Really appreciate your comment. Thanks for dropping me a line.
@cockasorrus7475 2 жыл бұрын
You are the enforcer of KNOWLEDGE brother! Your belief in getting closer to understanding the WHOLE concept of the workings within and troubleshooting, etc is spot on! I also concur wholeheartedly with the "dedication, self-confidence & belief" theory. I have rebuilt my powerglide in my 67 impala & the TH350 in my van and every time I drive either of them I FEEL A SENSE OF BEING CONNECTED! It's weird but I feel confident in knowing I DID IT! Maybe it's because I am not a accredited student of a trade school? I just really wanted to do it and did it! The beauty of it is there are great teachers out there such as yourself that help folks like me that want to do our own and feel that accomplishment! Thank YOU sir!!!
@SouthpawAutoworks 2 жыл бұрын
A power glide and a TH350...right on! I recall you mentioning future plans for a 700R4....in good time... I totally get what you're saying. It feels good to step of the old comfort zone, and tackle new things. It satisfies one of our most basic human needs; uncertainty. Dude, I really appreciate your ongoing support of this channel. It's always good to see your name pop up on here. Have a great week, man.
@cockasorrus7475 2 жыл бұрын
@@SouthpawAutoworks you did a fantastic job with the pathways! I built a TH400 I had laying around here also. I didn’t mention that because I have not tested it in a vehicle. It was a true experience building it as well. I have a 4L60/700r4 in my 76 C10. Somebody obviously installed it I haven’t gotten the truck back on the road to determine if the transmission is worthy yet. It may be a future project? The 47RE in my Dodge is great now with the ground issue resolved. (TCC searching) Most definitely on my agenda to enjoy the fruits of your labor!
@SouthpawAutoworks 2 жыл бұрын
Just now saw this comment.... For whatever reason, this comment of yours didn't appear on my end of things until today. Not sure sure what's going on... Right on. Really glad that you got that TCC issue sorted out. That must've been pretty annoying to drive.
@cockasorrus7475 2 жыл бұрын
@@SouthpawAutoworks you are burning 🔥 the candle at both ends brudda!! It’s all good! I wasn’t upset 😢 lol I am always happy to hear that you are doing well and I do appreciate your replies 🤙🏻
@saulohenriquef 5 ай бұрын
Thanks!
@SouthpawAutoworks 5 ай бұрын
You bet!
@kedcarcambioautomatico2929 2 ай бұрын
Good bless you
@PUBGMOBILE-mh9cd Жыл бұрын
Thanks
@SouthpawAutoworks Жыл бұрын
You bet. Thanks for dropping me a line.
@johnmwangi6291 Жыл бұрын
What ..!!you are the Man
@SouthpawAutoworks Жыл бұрын
Glad you liked it. Thanks for checking out the video, and for dropping me a line!
@Alejandro-sx8mb 3 күн бұрын
Thank you so much
@SouthpawAutoworks 2 күн бұрын
You're most welcome.
@amadormartinez1256 2 жыл бұрын
Bro keep the videos goin
@SouthpawAutoworks 2 жыл бұрын
Thanks for the support. Thanks for dropping me a line! PS If you're interested in spreading the word about this channel...here's an easy way to share (Friends, family, FB Group, etc) (Roughly 60-second video) 1 Handed Transmission Rebuilder: kzfaq.info/get/bejne/g9ymaKaVl8m6h2g.html
@user-du8cs8sn2v 2 жыл бұрын
Your videos are great Robert. I've just rebuilt my first 4L60e. I've only run it at idle and the line pressure gauge fluctuates rapidly around 75psi (it has the modified boost valve). I don't know if this is normal, or possibly related to the way the camshaft makes the engine idle lope. Once I fix an ignition issue I'll test the line pressure at higher rpm, but I now at least have a better understanding of how the pressures are controlled and what may be wrong (if anything). Thank you so much for your efforts!
@SouthpawAutoworks 2 жыл бұрын
With stock parts installed, the base idle should be right around 55 - 65 psi. However, aftermarket parts (stiffer PR spring) will elevate the base idle some. Thanks for dropping me a line!
@user-du8cs8sn2v 2 жыл бұрын
@@SouthpawAutoworks thanks Robert. I am more concerned about the manner in which the pressure gauge rapidly flickers at idle, but hope it will smooth out with more rpm. I expected the pressure to be elevated due to the aftermarket parts.
@SouthpawAutoworks 2 жыл бұрын
Shoot, I meant to address that part of your original comment. Sorry about that. A rapid/excessive flicker of the pressure gauge needle, at idle, can indicate that there's a problem with the PR Valve. In the case of the 4L60E, typically not an issue with the valve itself. However, you could be dealing with a worn out PR Valve bore (in the pump casting). There are some other checks to make with the pressure gauge. More on that, later.
@juansprojects3056 2 жыл бұрын
Being a mechanic for over 15 years and I'm finally getting into the automatic transmission rebuild process. Your videos are like none I've seen on KZfaq really helping me understand how this transmission works
@SouthpawAutoworks 2 жыл бұрын
Right on! That's awesome! Is the 4L60E your first auto trans? The positive feedback is appreciated. Thanks for dropping me a line!
@juansprojects3056 2 жыл бұрын
@@SouthpawAutoworks yes 4l60e is mine. I decided it's best to practice on my own transmission first before messing with anyone else's. Mine was shifting really good and firm for the first 300 miles after rebuild. Then got a p1870 code. So that's what I'm dealing with now
@SouthpawAutoworks 2 жыл бұрын
Having the ability to practice in private, before a public performance, is always nice. It reduces the pressure... Did you have that code prior to rebuild? During the rebuild, did you install any kind of valve-body kit?
@juansprojects3056 2 жыл бұрын
@@SouthpawAutoworks yes I did full rebuild. New pistons, zpak 3-4 new load springs new bushings all around, wide bushings where applicable, wide band. 5 pinion planets (both) trans go shift kit. Boost valve .500 reason for rebuild lost all gears including reverse. No p1870 prior
@SouthpawAutoworks 2 жыл бұрын
Right on. ****Regarding P1870 code**** If you don't already know...that code is typically associated with the Torque Converter Clutch slipping excessively. Some 4L60E models apply the clutch all the way...resulting in no slip. Some 4L60E models apply the clutch, but only partially....resulting in limited slip. They did this to help minimize vibrations, etc. Either way, the PCM monitors the amount slip. If it detects too much slip, it'll throw that code. Regarding TransGo kit: Page 4, covers the Isolator & Converter Regulator Valve. What was the OD of your original valve? 0.441"?? 0.472"??
@user-nr6ug4bu3k 8 ай бұрын
ты молодец хороший парень.
@SouthpawAutoworks 7 ай бұрын
Thank you.
@larryperry2094 Жыл бұрын
Great video. Really enjoyed it. I appreciate the time and thought you put into it. Solid knowledge brother. Well done and thank you.
@SouthpawAutoworks Жыл бұрын
Glad you enjoyed it! The positive feedback is appreciated. Thanks for dropping me a line.
@thegonz7833 25 күн бұрын
Very interesting and great delivery. Ive seen two so far and subbed, I use a Trans go jr. kits would be nice to know what TG is trying to achieve with each mod and change on a 60e
@johneric3886 7 ай бұрын
I think it's smart how you break up the video from time to time and have a little pauses. This helps my mind to recollect, it's thoughts & take a mini break.
@SouthpawAutoworks 7 ай бұрын
Right on! Glad to hear that! I'll keep this in mind for future videos. Appreciate your input.
@repairman969 Жыл бұрын
Robert Thank you for this excellent series of videos I have a 2001 GMC 4.8L last year when I turned from1 road to another (almost to a stop 90degree turn) and give it gas the trans seams like it goes to neutral I put a shift solenoid kit/filter & oil in and helped for a while I'm 67 years old and just learned to live with it, Now running on hwy it started fluttering and goes complete neutral and engine revs up a second or two then locks back in,, It seams okay when I start down the road (take off) and in reverse,, Any help would be appreciated, : Glenn
@SouthpawAutoworks 7 ай бұрын
It has me thinking fluid level? Do you know how to check the fluid level?
@armandokatime8854 5 ай бұрын
Hello, great information that you give in your videos, I have a question to ask about a 4l60e transmission, the transmission in question was rebuilt with all its new kit, corvette servo and sonax accumulators without pin, the problem is that it kicks when shifting 1-2 the rest of the transmission works perfectly, do you have any suggestions about the problem, what could be causing it? Thanks in advance.
@kudims 2 жыл бұрын
Great and knowledgeable videos, I watched almost all regarding 4L-60E. Question: if I want to make my vehicle start moving "happier" with brake pedal depress at Drive and no throttle (moving in traffic) - am I need to increase boost pressure in order to increase pressure inside TCC?
@SouthpawAutoworks 2 жыл бұрын
Thanks for the positive feedback. I'd like to answer your question, however, I'm having trouble understanding. Can you rephrase the question?
@kudims 2 жыл бұрын
@@SouthpawAutoworks when you stay at drive with brake on, and then you remove your leg from brake pedal, car starts moving. If I want car to move faster in such conditions, I need to increase momentum at TCC, right? To do this, am I need to increase boost pressure?
@SouthpawAutoworks 2 жыл бұрын
Thank you for clarifying. Yes, you would need to increase the momentum of the TC (Torque Converter). Just aheads up, the TCC is the Torque Converter Clutch. It's a clutch that lives inside of the TC. Some things that will have an effect on what you described are; 1). Engine idle speed. (this will increase momentum of the Torque Converter). 2). Torque converter design (stall speed)(angle of the fins that are used on the impeller/turbine). To the best of my knowledge, increasing the Line Pressure (via the boost pressure, or any other means) will not have have an effect on what you have described. Increasing Line Pressure will affect; 1). Clamping force applied to clutches and band. 2). Shift feel (soft, firm, harsh).
@michaelthul6013 Жыл бұрын
Thank you for a great video and all the time you spend making them .I was wondering why it is important to have a lower than line pressure feed going to the solenoids . Is it because the electric solenoids cannot operate under the higher line pressure ? or because the lower AFL pressure is needed downstream of the solenoids ?
@SouthpawAutoworks Жыл бұрын
Good question. I would imagine that the engineers did this (using lower pressures) as a way to conserve Line Pressure. If everything consumed line pressure, it would be harder to keep line pressure stable. Thinking it would fluctuate wildly. You can learn more about how the shift solenoids, and the shift valves, work by checking out these videos: 4L60E Shift Solenoid - Part 1 (Basic Operation): kzfaq.info/get/bejne/fMdzm7qeyNmll30.html 4L60E: 1-2 Shift Valve + Shift Solenoid (Part 1) Basic Operation: kzfaq.info/get/bejne/oLaYoJpnt6reZo0.html Thanks for dropping me a line.
@michaelthul6013 Жыл бұрын
@@SouthpawAutoworks Thank you for your quick response to my question . Your answer on conserving the higher line pressure sounds very logical to me . Now I'm thinking that the higher line pressure needs to be maintained so the clutches and shifting process work properly . Therefor I would believe your answer is correct. Thank you. I most definetly will be watching your other videos on automatic transmissions . Your videos are so nelpful and easy to understand in the way you present them .
@SouthpawAutoworks Жыл бұрын
Glad they're helpful.
@horacioanayaroman 2 жыл бұрын
Really good explanation and great work doing the animations of the fluid path. What is the app you used to illustrate the oil path?
@SouthpawAutoworks 2 жыл бұрын
I can't be giving away all of my secrets. ;) Thanks for dropping me a line!
@johnmwangi6291 Жыл бұрын
🤣🤣🤣
@rikkmalloy7892 2 жыл бұрын
Hi, I’m in Nc. I’d like to say thank you for your insight on facts. I’m working on a 2004 GMC envoy 2/wd 4.2 . I have no obd codes for transmission, but it slipping at 2nd to 3rd. And to get it to 3rd I’ll have it press the gas; and it still doesn’t feel good. Please please help me with this project. I’ve just put another transmission in the truck and really don’t wanna have to take it off. Also I’ve changed solenoids A/B. 4L60 E transmission
@SouthpawAutoworks 2 жыл бұрын
You're welcome. Questions: 1). With the shifter in D, when the trans tries to automatically up-shift from 2nd to 3rd, what exactly happens? 2). Does the problem occur when the engine trans are cold? Hot? Happens at all temps? 3). Believe it, or not, engine problems can/will cause transmission problems. Do you have any engine codes? Any other kinds of codes present? 4). What can you share about the currently-installed 4L60E? Rebuilt? Junkyard unit? As time permits, I'd be happy to try to get you pointed in the right direction. PS - If it feels right to you, please help me spread the word about this channel. Here's some easy ways to share with your favorite FB group, Reddit group, online forum, etc. Thank you. 1 Handed Transmission Rebuilder: (60-Sec Preview) kzfaq.info/get/bejne/r5mGnNuSxKvHYXk.html How the 4L60E valve-body works: (60-Second Preview) kzfaq.info/get/bejne/nL2AhsR9yseziH0.html
@rikkmalloy7892 2 жыл бұрын
@@SouthpawAutoworks yes cps / misfire #6. 1st&2nd smooth- 2nd to 3rd stinks. Help me please
@TeomaveBahia 5 ай бұрын
Very Very Very good! Like 👍👍👍👍👍👍👍👍👍👍🇧🇷🇧🇷🇧🇷🇧🇷🇺🇲🇺🇲🇺🇲🇺🇲🇺🇲🇺🇲
@CORVAIRWILD 2 жыл бұрын
2nd view from rainy Columbia SC
@SouthpawAutoworks 2 жыл бұрын
Right on! Thanks for tuning in...and dropping me a line!
@jodavaro1670 Жыл бұрын
💯💯🙋🏻♂️
@SouthpawAutoworks Жыл бұрын
Not a bad score... Thanks for dropping me a line!
@rockabichebel 2 жыл бұрын
I like all your videos In my 4l60e gen3 my line pressure gauge 55 60 psi maximum just on Reverse give me 90psi You think the boost valve ?
@SouthpawAutoworks 2 жыл бұрын
I have read your other comments, posted on the other two (2) videos. Have not had time to respond to those... I'm having trouble understanding your question, on this comment/video. 1). With the trans in OD mode, your foot on the brake, and the engine idling, what is the Line Pressure reading? A). If you take your foot off of the brake and accelerate the vehicle (part-throttle), does the Line Pressure increase? How much pressure does it build?
@rockabichebel 2 жыл бұрын
@@SouthpawAutoworks thank you for your reply On OD the max pressure 60 psi I have with my foot on break and second on throttle with 2500 RPm 2 also maximu 60 i dont have more than 60 psi Juston R reverse the max 90 psi
@SouthpawAutoworks 2 жыл бұрын
The Line Pressure should be roughly 55 psi with no load placed on the 4L60E (engine idling). But, as engine load increases (more throttle), Line Pressure should increase, too. This ensures that the clutches don't start slipping, and burn up (fail). Line Pressure is affected by: 1). PR (Pressure Regulator Valve) (Sets base line pressure [roughly 55 psi]). 2). The Boost Valve (raises line pressure above base pressure). 3). EPC Solenoid (this supplies oil pressure to the Boost Valve). 4). PCM (computer). (Controls the EPC Solenoid output pressure). 5). Engine load sensors (they "sense" engine load). If there's a problem with the engine, or one of the engine sensors, it can cause (or mimic) 4L60E problems. Questions: 1). Is the engine running good? 2). Do you have a check engine light on? Have you pulled codes? 3). Was the transmission recently worked on, or rebuilt? A). If recently rebuilt, did you do the rebuild, or did you hire a professional?
@rockabichebel 2 жыл бұрын
@@SouthpawAutoworks thank again and again My car hummer h3 2006 L5 3500 swaped to engine 6.0 gen3 tuning with MAF deleted with my h3 transmission 4l60e We change the bell housing and pump and torque converter and shuft and dram after that i drive the car for 2 months verry whell but i have a little slow shifting between 1n 2 n 2 n3 So we disasemble and change all the clutches and we change also the valve body steel plate When we make the test drive i find i have no power in the gears and start to slip on 2000 rpm n2 n4 gears after n3 gear 1 n R work good with no slip I use to test the line pressure i have no pressure max 60 psi
@richardjohnson4373 2 ай бұрын
I Have a Toyota Corolla that when you pull the shifter down into the low position the OBD tells me I am in 4th gear. I step on the gas and it is in first. Is this controlled by the 1-2 shift valve? It does have the code for silonoid p0741
@joffrejurado3030 Жыл бұрын
My first gear is not engaging. I replaced the 1st gear shift solinoid and nothing. I get solinoid circuit as trouble code, for all my solinoids. Also my ignition key won't come out of the ignition, not sure if that's relevant issue. Any suggestions?
@laritec1866 9 күн бұрын
I need help with my 2014 Chevrolet equinox..it failed to engage in drive after the gear service
@hw5091 2 жыл бұрын
this is fucking great. channels going to be huge man. Also, I have an '08 silverado, would those sonnax boost valve and pressure regulator vale work with that pump (I know there are a bunch of different models)? Also I have the turbine speed control sensor in the way of the boost valve, any way around that or does the pump have to be removed?
@SouthpawAutoworks 2 жыл бұрын
The speed sensor wiring harness is, unfortunately, in the way of the PR Valve valve-train (includes the Boost Valve/Sleeve) on later-model 4L60E units. In order to gain access to the PR valve-train, the trans has to be removed from the vehicle, and the pump has to be pulled out of the transmission. There are different lengths of Boost Valve/Sleeve, depending on year of 4L60E. Also, the PR Valves come in different sizes. There's the "regular" thickness (aka OEM), and there's an oversized thickness. If you suspect the PR Valve bore is worn out, you could either: 1). Use an aftermarket oversized PR Valve. Note: This requires oversizing the bore, and tools are required to do this. 2). Use an aftermarket valve that utilizes longer valve lands in order to use unworn parts of the bore, to essentially restore the health of the PR valve train. Just to be clear, it's not an oversized valve...just a modified valve...that requires no extra tools to get the job done. Your encouraging words are appreciated. PS If you're interested in spreading the word about this channel...here's an easy way to share with friends, family, FB groups, automotive forums, etc. (Roughly 60-second video) 1 Handed Transmission Rebuilder: kzfaq.info/get/bejne/g9ymaKaVl8m6h2g.html Thanks for dropping me a line!
@hw5091 2 жыл бұрын
@@SouthpawAutoworks Will do, and thanks for the reply. I was thinking the transgo lengthened pressure valve and new boost valve. I suppose I could get a new pump cover all together, and just use gm parts too. Also did the line pressure test, when I'm having a problem at idle (have to tap the gas slightly to engage 1st gear, otherwise its in a half neutral state), or shifting into drive (the problem only happens when the trans is warmed up past about 150f or so), pressure is about 46psi. After that tap of the gas pedal, it jumps to about 65 n goes like normal. When I'm not having that issue, pressure is about 65 or so at idle. Every other gear works just fine as you drive. R has no issue, neither really does starting in 2, but then again it's low torque so the delayed engagement could be there a bit, but not really noticeable. Judging by that, you thinking pr n boost valve is likely?
@fernandohood5542 2 жыл бұрын
How do you do those animations. A++++.
@SouthpawAutoworks 2 жыл бұрын
Very carefully... ;) Thanks for dropping me a line! Here's the latest video! It went live, minutes ago... 4L60E Shift Solenoid - Part 1 (Basic Operation) (60-Sec Preview) kzfaq.info/get/bejne/gL52nbCd2NfNoqc.html
@user-hp6tr5db4o 5 ай бұрын
Can a4l60 pump be surfaced on both sides
@SouthpawAutoworks 5 ай бұрын
If the pump is gonna get machined, then there are three (3) surfaces that need to get addressed. Great question. The pump cover is the half of the pump that houses the valve-trains. The pump body houses the pump rotor, vanes, etc. It's a common mistake to machine the two large surfaces on the pump cover and the pump body, and nothing else (only 2 surfaces). However, it's important that the pocket (where the pump rotor, etc lives) inside the pump body gets machined, too. If it doesn't, it can result in inadequate clearance for the pump slide (which needs to be able to pivot back and forth, during normal operation). Hope this makes sense.
@HajiWahid-hr7uu Жыл бұрын
Hi if you help me am a poor machine from pakistan When the gear jark(shaking) which valve is bad?
@29auto30 2 жыл бұрын
I'm doing a stand alone 4l60, and I don't want the shifts to be super hard, how can I control that with out the TCM? Could I use a rheostat switch? Thanks!
@SouthpawAutoworks 2 жыл бұрын
You mentioned "4L60"...which is another name for the 700R4/TH700R4. Yet, you are mentioning a TCM. I'm going to assume you mean the 4L60E. Please correct me if I'm wrong. Are you wanting every up-shift/down-shift to occur automatically? Or are you wanting to manually shift it for ever up-shift/down-shift? I'm not familiar with using a rheostat for a transmission. Are you thinking about using that to control the EPC Solenoid?
@29auto30 2 жыл бұрын
@@SouthpawAutoworks yes 4l60e, manual shift, wanting a stand alone for 4l60e, just wonder if there is a way to control line pressure with something?
@SouthpawAutoworks 2 жыл бұрын
Understood. Yes, I imagine that it's possible to control the electrical amperage supplied to the EPC Solenoid (Rheostat, etc). 0 amps: Max line pressure. 1 amp: Minimum line pressure. It's important to note, under normal operating conditions, the PCM varies the amperage. It varies depending on throttle position (TPS), among other sensors. The Line Pressure (via the EPC Solenoid/PCM) changes as the vehicle driving conditions change. I guess you could turn the Line Pressure all the way up, at all times. But, know that it's hard on the pump (probably reduce the life of it), it's hard on the rest of the driveline (shock), it'll make for one really hard 1-2 shift, etc. Wishing you the best on your stand alone 4L60E.
@philipwilliams6648 2 жыл бұрын
I am an old school mechanic and a retired auto body technician. I have rebuilt numerous transmissions in the past. I have attempted to rebuild my 4l60e in my trailblazer, may have been a mistake, acts as the pressure is to high. Keeps blowing cooling line off transmission. 5he4efore I am learning about the pressure flow. HELP if you can
@SouthpawAutoworks 2 жыл бұрын
Right on! (Regarding your experience with automatics and auto body repair) If the Line Pressure is in question, it would be a good idea to attach an automatic transmission pressure gauge (300+ psi) to the trans (pressure port located above the shift shaft lever, on trans). It should read right around 55 - 65 psi with the trans in Park, and the engine idling. However, I don't think Line Pressure is the issue... Automatic Transmission Pressure Gauge: amzn.to/3NWZGiX (Paid Link) These transmissions (and select GM vehicles) are known for blowing the cooler lines off of the trans (or the radiator). The 4L60E rebuild kit comes with two (2) blue colored E-clips. They're cooler line retaining clips. It's super important to replace those clips, with every rebuild. Furthermore, select GM vehicles have the cooler lines routed in a way that allows the cooler lines to move around too much. The excess movement causes the blue E-clips to wear out, and break apart......even brand new clips have been known to wear out prematurely. You might need to provide additional mounting points for the cooler lines, to prevent them from "jumping" around, during normal driving conditions. Hope this helps... DISCLOSURE: 🕵 Links provided are affiliated links with the associated websites. While there is no extra cost to the purchaser, a small portion of the sale goes to support this youtube channel. Thanks for your support!
@joemessina2293 Жыл бұрын
I have a question, I rebuild 4L60e'S all the time but i run into an issue with the 2009 4L60e's No matter what i do i get a 1-2 shudder. Never in any other year just the 09's Is that something common or is it just my nemmines ?? I do need help as i am lost on this one.
@SouthpawAutoworks Жыл бұрын
To the best of my knowledge, that's not common.
@caseyott7463 2 жыл бұрын
I have a 4L60e that slowly starts to overheat after 60-90 minutes of run time then starts to shift hard. It does have an external cooler. Any thoughts?
@SouthpawAutoworks 2 жыл бұрын
Under normal operating circumstances, the torque converter creates a lot of heat. The cooler is responsible for managing that heat. Plus, the TCC (Torque Converter Clutch), is also responsible for managing that heat, and of course performing other tasks, too. Do you have a check engine light on the dash/instrument cluster? Do you have a code reader, to retrieve codes? Inexpensive code reader tool: amzn.to/33uwVrj (Paid Link) DISCLOSURE: 🕵 As an Amazon Associate I earn from qualifying purchases. Some, if not all, of the links contained in this video description are affiliate links. This means that, at no additional cost to you, I will receive a small commission on any purchases you make through the website links provided above.
@caseyott7463 2 жыл бұрын
@@SouthpawAutoworks no check engine light on. I can check to see if it has any stored codes. The transmission was rebuilt a couple years ago. I'm going to change the filter/fluid and check to make sure the cooler lines aren't kinked. An external cooler replaced the radiator cooler when the transmission was rebuilt. Should I change the TCC solenoid when I change the filter?
@zaithwabanda4130 Жыл бұрын
What's the purpose of accumulator
@SouthpawAutoworks 7 ай бұрын
It's to soften oil pressure spikes...ultimately to soften the shifts, so they don't bang.
@osbyheaden156 5 ай бұрын
I have 200psi line pressure all the time , keeps blowing pump n can't seen 2 get it fix from shop
@SouthpawAutoworks 5 ай бұрын
Has me thinking these possibilities: 1) Worn out Pressure Regulator valve/bore. 2). Pump slide stuck. IDK the history of your trans (high mileage, recently rebuilt, etc), and I'm unable to road test, or scan your vehicle. So, I'm shooting in the dark...
@osbyheaden156 5 ай бұрын
@@SouthpawAutoworks po748 Rebuilt
@SouthpawAutoworks 5 ай бұрын
That code is aimed at the EPC Solenoid (Electronic Pressure Control). It has a direct impact on the line pressure...however, it's not the only thing that can affect line pressure. You can learn more about the EPC Solenoid, by watching this video... kzfaq.info/get/bejne/hr9hp9WLyrLVhIE.html WARNING: Do what I do at your own risk. If it were my 4L60E, I'd be taking a closer look at the EPC Solenoid. I'd monitor the EPC Solenoid with a scan tool, to see what the PCM is commanding (duty cycle), and also verify actual amperage passing through the solenoid. However, if I didn't have a scan tool (or if everything previously checked out on the scan tool), I'd gain direct access to the solenoid (drain oil, remove oil pan) and get my electrical meter probes right on the solenoid electrical terminals, and check the resistance. It should be right around 3.5 - 8 ohms.
@osbyheaden156 5 ай бұрын
Bad computer finally!!
@anesboitevitesseauto 5 ай бұрын
TOOOP
@saulohenriquef 5 ай бұрын
Why TCC is not fed by AFL?
@SouthpawAutoworks 5 ай бұрын
TCC stands for Torque Converter Clutch. There are two (2) different solenoids associated with the TCC. 1). TCC PWM Solenoid (located in/on the VB [valve-body]). 2). TCC Solenoid (integral part of the wiring harness, that's mounted into the bottom of the pump)(On/Off solenoid). The solenoid mounted on the VB is fed AFL fluid pressure. However, the solenoid mounted on the pump, does not. Instead, it's fed Converter Feed oil pressure. It's essentially line pressure. Hope this makes sense, and helps.
@saulohenriquef 5 ай бұрын
@@SouthpawAutoworks Thaks a lot. I got a manual and I didn't understand. Now All makes sense. Thanks!!!!
@SouthpawAutoworks 5 ай бұрын
Right on! You bet!
@robertholderman7552 Жыл бұрын
I got a 4L60 2002 I really appreciate if you could do something newer .. .. please “: • )
@SouthpawAutoworks Жыл бұрын
Copy that.
@marknaravas318 2 жыл бұрын
Great video, but I’m an old trans tech that sits down for hours and looks at oil passage diagrams for automatic transmissions. Kinda like my automatic transmission porn
@SouthpawAutoworks 2 жыл бұрын
Hahahahaha!!! Love it... Thanks for dropping me a line!
@marknaravas318 2 жыл бұрын
@@SouthpawAutoworks why don’t you show a rebuild of a really fun transmission like a AX4S or an AW-55 (those really are hateful shitboxes!)
@SouthpawAutoworks 2 жыл бұрын
Haha there ya go.
@SouthpawAutoworks Жыл бұрын
I'm scrubbing through past YT comments, looking for something...and I came across your comment. LOL Thanks for the laugh...again. Appreciate you.
@marknaravas318 Жыл бұрын
@@SouthpawAutoworks what’s the definition of a auto trans rebuilder: INSANE!
@lg1728 2 жыл бұрын
Hrh hos are you youf awesome on knowledge of 4l60e i got a 4l60d 4x4 2004 tahoe fullh rebuilt n made it 2 blocks n no gearz tranny wont do nothing no reverse or forwards gears znc ideas
@SouthpawAutoworks 2 жыл бұрын
I'm having some difficulty reading your comment...but, here goes. Questions: 1). With the engine off, check the trans fluid level. Start the engine, and check fluid level again. Did the fluid level drop? 2). What is the Line Pressure reading with the trans in Park, and the engine idling? Note: Use an automatic transmission pressure gauge (rated over 300 psi). 3). Did you happen to punch it (the throttle) right before you lost all gears? Automatic Transmission Pressure Gauge: amzn.to/3NWZGiX (Paid Link) DISCLOSURE: 🕵 Links provided are affiliated links with the associated websites. While there is no extra cost to the purchaser, a small portion of the sale goes to support this youtube channel. Thanks for your support!
@lg1728 2 жыл бұрын
@@SouthpawAutoworks j dudnf jack stand test 1st befor i tryed dri b ingnitnkm not goin lie to hou and yes sir i did punch it beforbi lost gesrx however sir i never had reverse at all andbghen ig started actin likebit was ckming around but forward was string but wojldng switch gears at likd never lock up and wouldvdlip and fluix sur was with a transt as r rebuild kit new torque convert we r piston all new clutchs all steels bew or c I eaned i mean all new bushings pump rebuilt all new papers andvseals a casebof new transtar fluid j mean all new barrings etc im a mechanic my friend helped me hse to rebuild don garlitts drag racing motorsvand transmissions for him hes got his shop here in houston anc thatsvwere i work also fullybredtoring cars ground up
@lg1728 2 жыл бұрын
My tranny lost all and no gesrs it wont do nothing new rebuild everythings new except the case basically
@lg1728 2 жыл бұрын
I made ut 2 blocks let off gas n then nothing and it wont stah in park either u think msin shift valuve in valuve body?
@brandtclark-truthbasedhors9110 Жыл бұрын
Great job
@SouthpawAutoworks Жыл бұрын
Much appreciated.
Southpaw Autoworks
Рет қаралды 24 М.
Southpaw Autoworks
Рет қаралды 19 М.
Southpaw Autoworks
Рет қаралды 47 М.
Precision Transmission
Рет қаралды 519 М.