I just did this exact swap on my 2019. There is absolutely no need to take the entire housing off. It’s very easy to do with it still installed.

Some people have posted that they didn’t have to remove the entire light assembly, which is possible if you’re replacement bulb isn’t too big/long. I went with the LasFit 7440NA bulbs which required me remove the light assembly. There was not enough slack in the wire harness on my 2018 SR5 once you put in the LasFit bulbs to make the turn back into the light assembly. Once removed, it’s a straight shot in. Especially if you install the bulb and it doesn’t work and you have to flip the bulb. Light assembly is finicky to get out with a couple of light palm slaps and reward pressure, but with a little patience it comes out as described in his video. Goes back in with no issues. Thanks for the video! Nice and helpful!

You can change the bulb without taking the light of the vehicle. Just remove the panel and reach in.

Thank you for all of the great content that you are pushing out for us all! I’m a new 4Runner owner and am loving all of the fun mods that are available and I’ve learned a ton from your videos.

All your videos are awesome. Thank you so much. They are definitely appreciated. 🙏🤘

both light bulbs can replace without remove whole assemply

Great video👏🏼👏🏼

Do you have a recommendation for LED daytime running lights that don’t flicker or shake?

i installed these Lastfit led lights on my 2019 4Runner but it does not work for the turn signals, only works for hazards. Tried switching 180 and opposite side but no luck. Front turns work fine, any suggestions????

I did mine in a 21’ limited and if you pull a little slack you can swap them without removing the light

My dad has an 20019 Toyota 4runner that has been doing weird things like thr back blinker lights have started flashing and no one is inside the truck I'd managed to get an video of it help

Swapped my entire housing for a different taillight. Was a pain in the butt trying to get my driver side off. Prob 10-15 minutes just working it off. Surprised I didn't break it

Thanks for the video. Did you change your interior bulbs, if so what bulbs did you use?

Is it me or is it that the rear led blinkers and out of sequence? its seems like tis flashing fast and slow at random times.

So I installed these in my ‘18, and the hazards work fine, but the turn signals hyperflash. Was told by Lasfit running front and rears can be problematic. Was thinking of returning these, but also read something about an updated LED relay?

Don't need to remove light unit to replace reverse light on 2021 4runner. 10 minute job....I did it.

Do you need to remove the whole housing to just replace the turn signal bulbs??? look liek you can just reach up and twist it out, no ?

Do they make amber headlights? Would be perfect for people who drive desert and city.

How come the link to the tear backup light on Amazon says it doesnt fit my 2020 4runner? I have a trd off road premium trim .

A lot of people on Amazon are saying these overheat in warm weather and start hyper-flashing after blinking for 30-60 sec. Has that happened to you?

Do you have the part number for the rear turn signals? or link?

The bulbs could NOT be replaced with the light assembly mounted ? It really needs to be removed, it looks accessible ?

You can just replace the light bulb with LED without removing the whole tail light right?

Are the actual break light bulbs replaceable

Purchased these for a 2018 Toyota 4Runner. They did not work, they hyper flashed. Got no help from Lasfit

No hyper flash?

Having a hard time getting my housing off.

I fell sorry for the person behind you when you turn on that blinker, Especially at night,, Thats hearting my eyes just trying to watch it on video.. I had to stop the video,, Why do thank you need your blinker that intense,, Turn off your garage light and set behind it for 2 minints and see if its not bothering your eyes,,