£50 NOCRY HVLP Paint Sprayer Unboxing and Review

Рет қаралды 7,624

Күн бұрын

In this video I am doing an unboxing and review of the NOCRY HVLP Paint Sprayer.
I got this from amazon for £50 because I hate painting and wanted to try something new, plus I love new tools!
Hope you enjoy and remember to like and subscrib

Пікірлер: 30

@terrywalsh8355 2 жыл бұрын

Thanks for taking the time to review this product. Using mine for the first time in a couple of days.

@MATTDOESSTUFF2020 2 жыл бұрын

no problem, hope it goes well!

@oliverstich1688 2 жыл бұрын

Good balance between need to know and wasting peoples time. Helped a lot - particular for beginners (me).

@MATTDOESSTUFF2020 2 жыл бұрын

Thanks appreciate it

@kroneditor9266 2 жыл бұрын

Good review - Thanks!

@MATTDOESSTUFF2020 2 жыл бұрын

Thanks, glad you enjoyed it

@annasecret2749 Жыл бұрын

Thanks for doing this for us

@MATTDOESSTUFF2020 Жыл бұрын

No problem, happy to help!

@pXnEmerica Жыл бұрын

Got a similar unit, it's weak point is probably going to be the plunger inside that attaches to the trigger. It's also the source of my biggest issue, the O-rings on the white plunger/pin didn't seal very well and paint was able to blow past them and started leaking out the holes where the trigger arm mounts. I added some greased cotton behind the o-rings and it helps to keep that from happening.

@MATTDOESSTUFF2020 Жыл бұрын

Nice, thanks for the tip

@tonyedmunds7633 Ай бұрын

I'm thinking of getting one of these to paint an old car. Anyone used this kit for anything similar?

@mrneako Жыл бұрын

can this be used with deck stain and/or deck sealer ? im looking for something cheap to run this behr stain and sealer through. left a buddy do the job since he said he painted in the past. well that did not turn out great, wife is absolutely pissed, half brushed on half rolled on and it really looks like crap. so hopefully something like this would be perferred and would make things look smooth and covered. great information, thanks

@MATTDOESSTUFF2020 Жыл бұрын

I dont see why not as long as you can thin down the product enough to go through the nozzles.

@andykuzemka2936 3 жыл бұрын

I did think the bit that held the paint looked a bit small. Can you buy bigger ones to fit?

@MATTDOESSTUFF2020 3 жыл бұрын

I don't think you can, its not a showstopper but would be good if you could get a 2 litre pot

@susanhigginbotham1806 Жыл бұрын

Even when I flick that lever, the pattern is still circular. Do you happen to know what I'm doing wrong?

@MATTDOESSTUFF2020 Жыл бұрын

I dont im afraid. The nozzles on mine spray either horizontal or vertical depending on which way the nozzle is switched. Are you holding it too close to the wall maybe?

@artsoto5459 Жыл бұрын

Would anyone know why it's not dispensing paint? It doesn't want to spit it out

@MATTDOESSTUFF2020 Жыл бұрын

Maybe you havent thinned it down enough? And also ensure you filter it. The smallest nozzles get blocked easily

@robertbailey1673 2 жыл бұрын

What was the finish like?

@MATTDOESSTUFF2020 2 жыл бұрын

The finish was good, it looks very even and flat as long as you keep the sprayer moving. I had a couple of areas that look a bit splotchy up close where i kept it in one spot too long but youd only notice if you got really close!

@marissasthe1 2 жыл бұрын

I got this sprayer and ignored it for a few years: just opened it and there is a piece that is not mentioned in the booklet and I’m not sure where it goes. A little black valve with a clear rubber thing on it. (Looks like a duck bill) 😂😂 Pretty sure it’s an air flow valve and goes under the paint lid. Do u know what I’m talking about? Lol. I was about to start painting with it (finally) and now I’m stuck🤦🏻‍♀️

@marissasthe1 2 жыл бұрын

Never mind! I saw it hiding in the last part of your video. Right where I thought it would go. They had it in the nozzle when I unboxed. It isn’t mentioned anywhere in the paperwork 😂

@MATTDOESSTUFF2020 2 жыл бұрын

Haha. glad you found it!