When fitting a new window regulator you just have to wind it right up, then hold switch in the up position for a couple of seconds and then it resets itself.

Typical 50skid- Not even two minutes in and already sharing a tool that's gonna make our lives easier. Would you mind dropping a link to that adapter + torx set? My most used tools are the Grey Pneumatic duo sockets you showed in the last tool bag video years ago, and the Bob Smith Instaset super glue has repaired countless things back to brand new. It doesn't get said enough- Thank you!

Great video, Jason. Thanks for sharing.

Thanks for another good E90 video. Helped me replace mine. Just had this exact thing go out on mine recently - Rear passenger side regulator just like yours. This video helped especially because I wasn't aware that that little handle plastic/leather covered piece popped off. Was good to know exactly what bolt/screw sizes were there too - T20 and 10mm. I also swapped out my dead trunk struts at the same time. Was possibly the easiest and fasts BMW part replacement I've ever done. New ones are cheap too.

use the up switch and hold for 10 seconds after you reach the top, then do the same for down and that resets the calibration on the window.

Good DIY video.

I think the way that works is if the door is open the auto up and down doesn't work. It's that way on my e53. On my E85 to activate it you roll it all the way down and hold the switch for like 30 seconds and then do the same going up. Maybe on the slow window you could lubricate the rubber track at slides in.

Just a short remark on the hall sensors: "High" and "low" only refers to the output signal of the sensors and won't correspond to the actual position of the window, they're just used for motion sensing.

Im in the U.S. virgin islands 🇻🇮 st. Thomas. Thank you for the shared knowledge.

In have same job to do currently. Good timing ! 06 325XIT 6spd manual.

👍 thanks for sharing!

As always educational thanks, 50skid can you please make video on Launch X-431 Pro 3S and explain the advantages using it from INPA ISTA+ MHD scanners(i own 135i n54)?

Yes MR JAson please show us whatyou keep in your tools sack for the junk yard

Hey 50s do you happen to have a junkyard tool cart I've seen a few cool ones I kind of want to build one or see you build one be interesting find the Pick-n-Pull is so relaxing we have one of the best in the state luckily I'm sure you have pretty good ones down there too in Southern California I say yes a new pick and pull bag load out video would be do

@50sKID amazing vedio as always.. I wonder if I could get a second opinion on this loud engine/fan noise I'm having on my e53

I don't even own an e90 xD

Good afternoon, what’s that attachment you had on the socket to use the hex bits? Thanks

Btw front face of the cup holders can be transferred with no problem.

Do you have a video on checking driver side window issues on a 740iL?

What, wood and a big random strip of rubber isn't normally found inside your door? It is in mine . .. I'm sure of it.

if only the front of the e46 was so easy

I know this is a random question but have you ever put a turbo on a e46? My main question is would adding a turbo increase fuel economy on our engines.

If you are ever in need of that butyl glue and don't want to pay a million, go to a professional building suppliers or contractors (concrete guys for example), they have the same stuff in caulking gun cartridges format! You don't have to buy the OEM stuff that comes in wax paper and in ridiculously small amounts

Need to look and see if you have an e46 DIY for a front regulator... :)

On my car, they wedged a piece of PVC pipe in the door to hold the window up. All that work, to avoid replacing a $20 regulator. 🙄

Yo it’s a matter of resetting it.

Huh huh huh, he said "length" !!!

Hello 50s k please you help me with fuel injectors for my BMW e46 328 MS43

It's called window initialization.. can be done directly from switch ..but buy the tool first

lol you need to wear a do-rag and rubber gloves to do this job?

When refiting the vapor barrier you need to renew the butyl otherwise the barrier won't stay sealed against the metal and you will have a nice water leak ...oops 40 years on BMW.

The cup holders in this car are beyond dogshit. I never use mine, they feel so flimsy.