5F11 Vibrolux | Input Jack Oddities

No video

5F11 Vibrolux | Input Jack Oddities

Рет қаралды 7,392

Psionic Audio

Күн бұрын

Пікірлер: 33

@rustyrobinson8027 Жыл бұрын

Since uncle Doug isn't uploading as much I'm glad I found your channel thanks 👍

@duderdudeedoo1984 Жыл бұрын

I hope Uncle is going ok. Love that guy’s videos

@williambock1821 Жыл бұрын

If the owner wants you to re wire the heaters, it might be fun to hear the difference (if possible with a recording) in a future video.

@roncarter2188 Жыл бұрын

First cup of coffee at 8:30 and working on cool vintage amps.....your living the good life Lyle!

@retread1083 Жыл бұрын

I'm fond of using a pair of resistors to simulate a heater center tap. I'm also a fan of biasing the "center tap" at a DC voltage that's more positive than the cathodes in the preamp stages.

@nolarocks Жыл бұрын

Good vid. Really enjoyed listening and learning.

@sgt.grinch3299 Жыл бұрын

Deep dive into the secret sauce. Thank you Sir.

@stratofig Жыл бұрын

Put a footswitch in one of the open jacks and you can switch between two different gains.

@jerryking2418 Жыл бұрын

Thanks for the info.

@danielsaturnino5715 Жыл бұрын

Ahh the lower octave morning voice. Sounds like a radio show.

@muntor7935 Жыл бұрын

Thanks for the vid Lyle. When you say lav mic clipping I assume you actually mean the lav mic clipping the input of your sound-card. You may be able to put a Y cable from the mic to two inputs of the sound-card and run one at lower gain, then pick the appropriate track in editing.

@PsionicAudio Жыл бұрын

I just run the lav into the phone for on the bench recordings and adjust as needed. For real playing videos the amp gets a separate mic and I mute/unmute the lav in post.

@waynegram8907 Жыл бұрын

Does the Selenium Rectifier Add more SAG compression? any reasons why they used selenium rectifiers

@oldguy5381 Жыл бұрын

Hi Lyle, busy as ever I see. Don’t work too hard.

@cgavin1 Жыл бұрын

Always been curious about the yellow and white Mallory (M150?) caps (not the old electrolytics Fender used in the 70s). I always seem to see a mixture of those and rarely all one or the other. Do they have different characteristics or is it just that the yellows pre-date the whites?

@audiotechlabs4650 Жыл бұрын

Lyle, you know so much about these tweed amps. I have a 1957 5E3 and I want to do some what I call upgrades. Would putting in a choke where the 5K dropping resistor is for the screen grids make the amp more quite or is that too much voltage on the 6V6s screens? Also the 5F11 has a neg. feedback 56K resistor. Would that give any benefit to the headroom or overall volume output of the amp? The heater supply change like you describe one could do like it this 5F11 would also be an upgrade. You really know your your stuff on tube amps so any input from you on these subjects would very helpful! ❤️🌨 Colorado. Thanxz

@PsionicAudio Жыл бұрын

Thanks man. I wouldn’t mod a ‘57. Choke won’t give much/any benefit. NFB changes the character but again, it’s a ‘57. If you want to see some subtle effective changes look for the ‘58 5E3 on here.

@samuel_towle Жыл бұрын

A coffee before play keeps EMBS away!

@JEmilioJNava Жыл бұрын

"Bipolar Heater Supply" ... new tech term, yay!

@PsionicAudio Жыл бұрын

It’s not quite accurate. I should have said balanced. Insufficient coffee tech speak.

@richardlynch5632 Жыл бұрын

So...this clients amp is bi-polar...?🤔 Cool amp...really looks like a cool design 😎👍

@russellesimonetta9071 Жыл бұрын

So,, to simplify,,, input one is P A, input two is kind of P A and input three is kind of P A but best for guitar.

@johnwilliamson467 Жыл бұрын

Coffee helps with EMBS . Well the 50ohm RCA connector are at best they are cheap . Used by most so changing to a far better connector not in the cards for most people. Cost control is a major factor in that amp . Not using a center taped heater is more lazy than cheap given you can make a pseudo center tap with 2 resistors .

@goodun2974 Жыл бұрын

Yeah, you expect to find an unbalanced heater supply in a single-ended, student-level amp such as a Champ, but not in a mid-level unit like a Vibrolux. Actually, you could argue that the single-ended amp needs a balanced heater supply more than the mid-level push-pull amp, because the push-pull amp has better common-mode rejection and would cancel some heater-circuit hum in a way that the S-E amp would not.

@johnwilliamson467 Жыл бұрын

@@goodun2974 With S-E amps I prefer a dc heater regulated to 97% rated voltage and elevated about 45 volts above ground reference . Found that the h-k internal capacitance need that bias to be quieter. This is a bit in the weeds for most people .

@retread1083 Жыл бұрын

@@johnwilliamson467 there's more than the internal capacitance in play here. If the cathode is more positive than the heater in any part of the ac cycle, it will draw a small amount of current and introduce noise. DC supply for heaters isn't uncommon in the hifi world but adds more complexity (and cost) than we usually see in a guitar amp. A pair of resistors to emulate a center tap and biasing that well above the cathodes in the preamp section is a dirt-cheap and effective improvement even though it's not as effective as a DC heater supply.

@johnwilliamson467 Жыл бұрын

@@retread1083 interesting does give a fine reason for the need for bias of at least 45 volts. Have seen bias tap on power trans work as an ac bias 70 volts . Works very well .