Ohhhhhhhhh....was boutta say excuse me mate you seem to be a bit clogged up there

Same😂🤘

lmao

OHHHH THAT EXPLAINS ALL THE WATER tyyyyyyy

Fucking same i was so scared. 😭😭😭😭😂😂😂

It’s a boat engine tho

@@fox0013 joke went right over ur head

@@fox0013 R/Woooooosh

@@fox0013 think about the joke bud 😂

hahaha

me too

Mostly because they runing high rpm when using. They dosen't have gearbox.

Haha I thought the same 😂

Its just theme probably

win xp with classic look

same on many engine video

thanks for watching my channel 👍

Ни когда такого не было и вот опять! 🤔

@@user-louzer можно яснее чего не было можно узнать?

Спасибо человек

я думав то бензин незгорівший з вихлопних так валить😆😆😆

Я думал на водороде ебенит, а при этом вода в током количестве выделяется.

Thanks for watching my channel 👍 please watch my other videos!

My raw water pump on my 350 onboard can drain a 5 gallon bucket in under 45 seconds at idle.

thats fuel economy not water :D

What does it use the water for? Instead of coolant?

@Jeff Spicolli Antifreeze increases the boiling point of water up to a certain percentage.

@@Cragified Everything will be up to a certain percentage. Pressure also increases the boiling point. Pure water actually has better cooling properties, than water with antifreeze in it, hence locomotives do not use antifreeze, just pure water, but drain the cooling-system if parked in cold conditions.

Thanks for your comments!

Ikr I love that idle 🥰

sounds like my dads 79' c3 at idle

The water cooiling of the exhaust creates exfra burbles that sound nice

Its sealed, aint gonna hurt it.

It's only a problem if it starts sparking

@@rileymannion5301 well its not gonna start sparking...only thing that miiight happen is some current could flow through water on the top of the battery between the terminals. But its fresh water so its not very conductive at all and its only 12 volts, so its unlikely ample current would be flowing.

@@Thebadbeaver9 finally someone else who understands how this works

@@untitled2792 yeah lol, although I cant fault people for being extra careful around any electricity...

Good bro

@Li Zhi-qiang - META are you asking me ?

grrrrowwww

Thanks Roman 👍

Great ware the tools out and find a use for the case , recycling at it ,s best .

Thanks for watching my channel 👍

Почему вода льётся из выхлопа?

Thanks for watching my channel 👍

Thanks for watching my channel 👍

Thanks for watching my channel 👍

Thanks for watching my channel 👍

Thanks 👍

Thanks for watching my channel 👍

@Joshua Jay Lanfear joking.

It runs on Swedish meatballs.

@Joshua Jay Lanfear i beg to differ, the engine is running, water is coming out, corrolation equals causation as we all know

@Joshua Jay Lanfear bruh i literally said “correlation equals causation” when the saying is “correlation DOESN’T equal causation” of course im joking

Yes; why did'nt they invent that earlyer by now?

Its basically a clone design of the 96 through 2000 Chevy 350 block

@@dalebills9470 yeah, mercury motors are a GM company.

@@Leo-oq7ir I'd get rid of that goddamn distributor cap, things were notorious issues on the engines that used them.

Thanks Andy for watching my channel please watch my other video's 👍

Cause it is :)

@@mdubz101 It is a sbc not an ls, you can see a distributor on the rear of the engine.

Thanks for watching my channel please watch my other video on 4.5 V6👍

@@jonesllew5201 okay

Hope you don't have carpet

Lmao me too 😆😆

That engine would make a perfect sand buggy/ ultra go kart slap a 2 seater Jeep Wrangler cab and weld a roll cage, slap on a 2011 ford ranger transmission 5 speed with a custom shifter, huge a$$ tires and for the cooling system, you can install a cooling fan that runs off the engine, a radiator with a huge radiator hose going to 2 water tanks pumping and leading back to the radiator and the fan cools it off. And install the gas tank to a 25 gallon gmc SUV gas tank with the same fuel pump setup as shown in the video, wire the ignition to a dash from a 1980’s truck. Have the battery under the seat and have a fuse box under the hood. For the exhaust you should put 2 massive pipes leading out the passenger door. Idk just a thought if the motor was to be used for a cool reason.

You must be single ? The wife, kids and dogs would not allow it ?

@@yuccaken lmao what

Thanks for watching my channel 👍

Thanks for watching my channel please watch my other video's on water cooled exhausts 💦👍

Thanks mike!

Thanks for watching my channel!👍

Juhhh😂

I’ve got a pair of 8.2 / 496 MAG/HO in my boat 275hrs trouble free.

You can speed density tune a closed loop and kill the o2 sensors aftermarket on just about any engine. I don't know of any places that emissions test boats so there's no technical reason why you couldn't do this. It was quite common to use the MEFI boxes for LS engines in vehicles where they didn't need OBD2 ports.

@@scottleggejr You should do a “how to video”. Just change your name, wear a mask to hide your identity and have a disclaimer that this it for educational purposes and this performance mod should never be done to save money and keep an engine running🧐

@@SkypowerwithKarl I have a couple videos on my channel of a desert bronco I built with an LS swap. The mefi boxes are extinct as far as I know now. I don't have a v8 boat anymore either 😭

@@scottleggejr Yeah, I can relate. I sold my boat 2 years ago and I still have withdrawals but I don’t miss the bills. See “Big fast houseboat” on KZfaq. It has twin vortec 5.7L EFI’s. Oh and MEFI 5s lol.

I thought he was from Wales

Huh? Through its cooling system like all other combustion engines?

Less than a car engine as its not a pressurized system.

pumps don't require much energy.... Try imagining the engine running without it. LOL

@@mrmedium7984 a car engine water pump doesn't work really hard because the pump isn't the thing creating the pressure. it just circulates the water

@@MadEvo606 good explain

Thanks for the advice I have had a lot of problems with the cap's 👍

@@jonesllew5201 what flipping the gear does is mechanically advance the timing at the distributor. This lowered the voltage the cap sees so it doesn’t pop. You can also rotate it physically but there might not be enough room. The PCM automatically locates the distributor on cranking so it can be located anywhere between the #1 and #2 cylinders. However the allowed position needs to be updated in the calibration to account for this. In my vehicle I actually put the dist. with 25 degrees of advance so I can run more than 40 degrees of timing during cruise. That said moving it only 15 degrees may work fine as it’s allowed to be +/- 30 degrees before a code is set. Use timing tape for accuracy, tho, and be careful on the first start. It should sinc right away but if the starter is straining then it might have not updated the distributor position yet. You can double check it after startup with a timing light. The timing should be the same, less any idle corrections which cause it to wander a bit on the timing tape. If it worked there should be no DTCs set.

Thanks for watching my channel 👍 please watch my other video's

Thanks for watching my channel 👍 please watch my other video's

Yes! I love big outboards . check out my other video's on them.thanks for watching my channel 👍

1.25 gallons per hour, that's like what 5.7L per hour if UK gallons or 4.7L if US gallons. My car engine for comparison idles at the same 675rpm but consumes only 0.4L per hour.

The don't call boat ownership 'standing in the shower tearing up £20s' for nothing

They're basically Chevy small blocks and big blocks

Thanks for watching my channel please watch my other video's 👍

Good luck with the water lmao

@@kuiper921 he's gonna run a pump from his cat lmao

and ofc Vtec on top ye ? ;)

Hector said the same 😂😂😂

Thanks for watching my channel

No problem john!

GM!

@@jonesllew5201 I thought the same thing looking at the distributor and valve covers …..

Yep, GM small block. Basically a 350 cu in stroked to 377 .

Thanks for watching my channel please watch my other video on water 💦 cooled exhausts 👍

Походу пробита прокладка под головкой

Лодочный мотор

@@user-rp7vo3mf3e я уже это понял,но вам спасибо за информацию,это охлаждение! У лодочных моторов нет радиатора и охлаждение реализовано путём закачивания забортной воды и выбрасывается через выхлоп,тем самым и звук вода приглашает и ускоряет воду создаёт давление и циркуляция лучше.

@@user-ie4pv9vv5e это у тебя под головкой пробита прокладка.

gallons of fuel spitting out

It's not a boat engine the head gaskets are blown

😂😂😂😂😂👍

Это пиздец, даже по меркам России))

Thanks for watching my channel 👍

The exhaust manifolds on most boat engines are water cooled. The water is pumped into them and exits the boat through the exhaust pipes.

@@UHOH3300 The entire engine in this case is lake or river water cooled and the waste heated water is put overboard in the exhaust.

@@JimNichols true, mercruisers dp that. As a result, they don't last very long in saltwater lakes/oceans. For saltwater service I would absolutely prefer a Crusader if I was getting a small block GM

You can also get closed loop cooling on Mercruiser. Some of my buddies have it on their boats.

Thanks for watching my channel 🙂

А я то думал что за помпа

Thanks for watching my channel please watch my other video's 👍