trying to make your bedside cut downs a little easier for ya
Пікірлер: 37
@justinfletcher5189 Жыл бұрын
Best video on the internet for 67-72 bedsides Did one last night and going to start on the 2nd one tonight. Serious Props to you!
@jeffosborne22872 жыл бұрын
Hands down best informational video I've seen yet for these beds. And props to you man for doing it for free 🤘
@kenvander764 Жыл бұрын
just finished this project put the laptop on the box side and followed your steps religeously Very happy with final result and believe this is the best method i have seen . Thanks a million for taking the time to post this . More fun than buying a new box !
@martinbrown812 жыл бұрын
Massive thanks to you man for doing this video. You really show a brilliant way to do this. Thanks for helping all of us out. Cheers!
@Kevin-kb6uq2 жыл бұрын
Excellent work. Very clear directions. Greatly appreciated, thanks!
@yamahaxs6501 Жыл бұрын
I really like the way you do the front edge. Just taking my bed apart today.
@tinocairo6605 Жыл бұрын
Very very detailed, thank you.
@unfadeaway2 жыл бұрын
Great video much appreciated!
@justoyzracing919311 ай бұрын
What the measurement of your square for the angle line?
@BattleOfBowties Жыл бұрын
Great job!
@harrytaylor68542 жыл бұрын
well done very cool
@chicali-626-martinex52 жыл бұрын
👏🏽👏🏽Really Good Explain Videos..👌🏽👍🏽Like your Videos
@theaveragebear78732 жыл бұрын
Man that looks good. Gotta find someone in San Diego to do this to my C20.
@leonardtriolo2475 Жыл бұрын
What do you charge for the conversion
@jimmyrobertson3793 Жыл бұрын
Great video! Will the angle degree for the rear cut be the same if I cut the 12 inches right after the side marker light?
@duendegarcia1509 Жыл бұрын
How much do you charge?
@shawnwimberly92942 жыл бұрын
I'd be interested to see more of the cutting and welding processes, maybe see the seperate pieces before you do the assembly. Maybe when you do the marker light video. Looks like a solid method, I've watched several approaches to this on different videos and yours makes the most sense for me and my abilities. Spot tack removal/bedstake removal was unclear for me though.
@shawnwimberly92942 жыл бұрын
Seemed like a lot of stuff happened off camera at about the 20 minute mark to me.
@coyotecustomshotrodsandmet91382 жыл бұрын
I will be making a video on welding tips and tricks and wire I use and heat I run
@shawnwimberly92942 жыл бұрын
@@coyotecustomshotrodsandmet9138 that's cool, I've got a pair of bedsides cut down now using your video as a guide. I'm no welder but I've got a buddy that will put them together for me, so far it wasn't horribly difficult thanks to your insights. I eliminated the marker lights this time, but I've got another spare bed and two complete trucks to go. The idea is to practice on the extras then when I've got it down, do it to my daily(and z cut the frame). Thanks again Sir
@shawnwimberly92942 жыл бұрын
I've got two sets of bedsides and one truck all the way done now. they're not bad considering my limited welding experience. any way you can pm me a price to do the bedsides on my daily?( 72 c10)
@freddyhernandez48492 жыл бұрын
Someone knows of a book that indicates the measurements
@IowaMercMan3 жыл бұрын
Slick. Is it possible on the front cut, to hide the entire weld line behind the stake pocket?
@coyotecustomshotrodsandmet91383 жыл бұрын
Unfortunately no I wish
@Timgrantham662 жыл бұрын
Good job man! Now let's see a 60-66 lol
@coyotecustomshotrodsandmet91382 жыл бұрын
Doing one in a month I will trying to get a video of it
@hermantom42922 жыл бұрын
What size wire are you using &the heat setting....nice work
@coyotecustomshotrodsandmet91382 жыл бұрын
0.30 wire with 75/25 gas
@dannyneufeld9542 жыл бұрын
I see a lot of people saying that the angle in the back should be 23. I was wondering how straight that body line was in the end. I like your way of doing it
@coyotecustomshotrodsandmet91382 жыл бұрын
Clean no problems you can check out my work on Facebook page same as the KZfaq page name
@NeufeldGarage2 жыл бұрын
@@coyotecustomshotrodsandmet9138 ok sounds good thanks! I actually just finished cutting and welding my bed using your method and it worked very well👍
@shawnwimberly92942 жыл бұрын
At 2:49... what's the measurement of that first mark? How much of a jog do you recommend there?
@shawnwimberly92942 жыл бұрын
3 inch?
@BattleOfBowties Жыл бұрын
Maybe I'm the only one but short beds are overrated I've had mine for 15 years and it's just hell for real work. If I had it to do again I'd definitely buy a long bed.
@SeaDooEric2 жыл бұрын
Turn the phone
@HollisLawnServiceLLC3 жыл бұрын
Where are you located? Could you send me your contact info? I need this conversion done on my 70c10.
@coyotecustomshotrodsandmet91382 жыл бұрын
I have a Facebook page under Coyotecustoms You can look me up there or you can give call or text at 918-752-5039. Located Sand Springs Oklahoma