6T70 Rebuild Part 2. 6T75 Rebuild Part 2. Transmission Assembly. Transaxle Assembly.

Рет қаралды 15,037

Күн бұрын

Part 2 is finally here. This transmission is being dissassembled after the video to donate parts to a couple other transmissions that I have to repair yet so yes things are dirty and thats ok. Thanks for watching.
Merch: www.teespring....
Tools:
Socket Set: amzn.to/34wP588
Jack and Stands: amzn.to/34Ke5t0
Ramps: amzn.to/2SB1QJz
Serpentine Belt Tool: amzn.to/3dbspyd
Ratchet Wrenches: amzn.to/3jHtdxu
Drain Pan: amzn.to/3iKhqwQ
Funnel Set: amzn.to/33MHpQl
Social Network Links:
Website: www.dmoneygarage.com
Facebook Page "DMoney Garage" @dmoneygarage www.facebook.c...
Instagram: thegaragesteve3
Contact Email: thegaragesteve@gmail.com
Notice:
Due to factors beyond the control of DMoney Garage, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. DMoney Garage assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. DMoney Garage recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of DMoney Garage, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of any tools, equipment, or information contained in this video is the sole responsibility of the user and not DMoney Garage.
Credits:
Music: www.bensound.com
Intro & Outro: www.fiverr.com
"Steve Demo is a participant in Amazon EU Associates Programme, an affiliate advertising programme designed to provide a means for sites to earn advertising fees by advertising and linking to DMoney Garage"
#transmissionrepair
#chevy
#howto

Пікірлер: 31

@anthonykimble5278 8 күн бұрын

Can I pull the differential from a fwd and put it in a awd case

@dkstiver Жыл бұрын

woah, i literally make 4 of the parts in that transmission for my job

@michaelguevara8015 10 ай бұрын

Just got a 2012 acadia It shifts fine once you get going, just when you first put it in drive it takes a little moment to engage And when it gets to 60mph at below 2k rpm the speedo needle bounces a little up and down and it feels like a gear engaging and disangaging if that makes sense. Could it be the torque converter

@josephlovell6951 7 ай бұрын

I have 1 with a intermediate pulse that I believe is a bad torque converter. So I got a used one that has a slip on the 2 3 shift that is causing a traction control

@lovetofishneosheo1829 Жыл бұрын

Thanks for your video. At 130 it’s hard to tell what way you lay the spring in, are the ears out towards you. Thank you very much for the video

@alexyudenko8157 3 ай бұрын

How much PSI are you applying for the air test, I don't want to damage the seals by over pressuring.

@patriciabyers1747 Жыл бұрын

Let's hope you could answer a question I have , when you installed the 1-2-3-4 piston and you put the bellville spring on , then the retaining ring, did you put the tabs on the bellville up or down, I can't really tell by your video?

@josephlovell6951 7 ай бұрын

Problem . Thinking of just getting a torque converter for the first one. Any problem with that?

@blitz8619 Жыл бұрын

Is it possible to replace the 456 clutches in vehicle. By dropping subframe. And removing end cover.

@mshupe021 Жыл бұрын

Is torque converter lock up solenoid in the valve body?

@user-te9zq3ci1p 7 ай бұрын

Can i put the 6t70 on a 2wheel drive ?

@SheikBaksh 3 ай бұрын

you are using the wrong 1234 piston for the gen 2

@wantharley 5 ай бұрын

Hi. I have issue with my impala limited 2016 it is about 65k. Once I shift to D, car doesn't move with RPM. Or move but very shortly. shift to R and ok. I was in mountains when it start fail to move. But I manage to drive back home on manual mode , 3 gear. Problem is that I am in italy an here no one knows what to do. Please advice, what can be the root cost of this failure. It is ex PPV from Police

@BuickPerformanceSupportCha1605 10 ай бұрын

You didn't mention replacing bushings. I guess just inspect them if their bad replace them??

@DMoneyGarage 10 ай бұрын

Yea. Sorry. This was a core I slammed together for a video before scrapping. Lol

@BuickPerformanceSupportCha1605 10 ай бұрын

@@DMoneyGarage Oh ok Cool!!!

@billybowbob2071 11 ай бұрын

Great video! Question though, if everything is in place correctly, why would the cover plate not seat fully against the transmission? All the thrust bearings, gears and clutch plates are correct, but the cover sits maybe 1/4" high... Any idea?

@DMoneyGarage 11 ай бұрын

Definitely sounds like something isn’t seated right. As for what it is there are a lot of options. I would def go thru it slowly and make sure everything lines up. It can feel “good” but not be right. If that makes sense

@billybowbob2071 11 ай бұрын

@DMoneyGarage it makes sense. I've been through it about 7 times and just can't figure it out. Time to find a transmission shop and have then swap in a reman.

@salvadorberberaramos9144 Жыл бұрын

Where can I buy this rebuild kit I have a 2008 gmc awd Acadia

@gabrielescareno323 Жыл бұрын

First thing great videos, Part 1 and 2 were what I needed to tackle the job. I have a Buick Enclave and have worked on my vehicles to make them last a while. I am mechanically inclined but when it comes to transmissions well I can remove them and install them. But tear them down, I was always skittish about all the parts involved. Now I am faced with the challenge of either purchase a refurbished or buy the rebuild kit for it. My vehicle is performing now with a shudder at 3 gear going into the overdrive. This happens at around 35-40 mph. I have heard that it could be the torque converter and others have said wave plates. Would you advise to rebuild it or just swap it with another. I know money wise its cheaper to get a kit along with a new torque converter but I was trying to weigh my options. is it worth the time and money? What is your advise and what are the common factors to my symptoms. Any help will help me. Thanks Gabe

@anthonykelley368 Жыл бұрын

You got the exact same problem I have with my 2016 Enclave... So instead of asking what you've already asked, I'll just check back in for a response... I'm looking at just replacing my entire trans with a corrected remanufactured one from a company that specializes in these exact GM transmissions... They run about $2300 with the core...

@spacecowboy2k Жыл бұрын

I also get the shudder, it's occurring from 1400-2000 rpm in 3rd gear, and I can hear that mechanical "percussion" noise that sounds like an old-school metal percussion fire alarm bell. I'd rather rebuild if I can! 2016 Chevy Traverse.

@6550EL346L6 2 жыл бұрын

I didn't see you install output seal. On the right side how far down does the seal drive in? Does it bottom out when it's installed? Do you use any rtv or grease before installing on the outside edge?

@DMoneyGarage 2 жыл бұрын

This transmission didn’t get that seal since it’s all wheel drive but it doesn’t bottom out. I usually drive it down like 1/4 inch from the edge of the trans.

@6550EL346L6 2 жыл бұрын

@@DMoneyGarage Is there a vent on this transmission? For front wheel drive 6t70.

@Topshottayut Жыл бұрын

Where do you get those disgrams

@DMoneyGarage Жыл бұрын

Those are gm documents. But alldata has them also.

@skooter7 2 жыл бұрын

Hey where are you located I need to bring my truck to you

@DMoneyGarage Жыл бұрын

Northeast Indiana

@hunterwinters587 9 ай бұрын

@@DMoneyGarageyoooooooo me too I got a 2012 chevy impala 6t75 I want to get a transmission rebuild/ shift kit upgrade installed is that something you could help me with? I'm mechanically inclined but haven't ever worked on a transmission.