75. Sorting the plumbing in the campervan

Рет қаралды 26,558

Жыл бұрын

Having replaced the sink in the new worktop, I needed to sort out the sink outlet for waste water and the supply pipe from the main tank. This proved irritatingly troublesome, as you will see!
If you liked the video and wish to leave me a tip, here's the link: www.ko-fi.com/davidjohns and thank you!
Tools & Parts used for my campervan build
Autoterm diesel heater: geni.us/Van_Autoterm
Renogy 2kW inverter: geni.us/Van_RenogyInverter
Sink: geni.us/Van_NewSink
Induction hob: geni.us/Van_InductionHob
Portable toilet: geni.us/Van_Toilet
Fridge: geni.us/Van_CoolFreezeCDF26
Charger: geni.us/Van_MainsCharger
Solar Controller: geni.us/Van_SolarMPPT
Gas Alarm: geni.us/Van_GasAlarm
Old sink unit: geni.us/Van_SinkHob
Old heater unit: geni.us/Van_PropexHS2000
Old inverter: geni.us/Van_Inverter
DeWalt jigsaw: geni.us/Van_DeWaltJigsaw
DeWalt drill: geni.us/Van_DeWaltDrill
DeWalt mitre saw: geni.us/Van_DeWaltMitreSaw
DeWalt circular saw: geni.us/Van_DeWaltCircSaw
Web www.vandemonium.co.uk
Twitter / vandemoniumuk
Instagram: / vandemoniumuk
As an Amazon Associate, I earn from qualifying purchases.

Пікірлер: 371

@deanmills5106 Жыл бұрын

You never cease to amaze me. You take a simple mundane task like fixing plumbing in a camper van and make it interesting. Not only interesting but fun to watch and informative believe it or not. It really does amaze me.

@mattevans-koch9353 Жыл бұрын

I always enjoy your videos because of your sense of humor and you narration. Thank you David for a truly enjoyable Friday evening. And that is quite the cliff hanger at the end. Have a great weekend.

@pfsmall Жыл бұрын

Barbed fittings are not meant to seal on their own. You just needed a hose clamp on the water line or as you call them a jubilee clamp. Nice work though!!!

@CaptainArloNJ Жыл бұрын

Took the words right out of my mouth. I'd redo that without using any sealant and a clamp on each fitting.

@carycoombe3380 Жыл бұрын

And if the hose is too small to fit the regular hose clamps, two or three zip ties, pulled very tight, should do the trick.

@marks-0-0 Жыл бұрын

Yes come on David just use a hose clip Lols plus using a sealant on top of a leak never works 👍

@fredturk6447 Жыл бұрын

Agree entirely. Also suggest using marine grade stainless hose clamps not zinc coated ones. Take the sealant off, take the hose off and put a good quality hose clamp on it, if you don’t use hose clamps it will eventually leak!

@t1n4444 Жыл бұрын

Ah, well, now ... barb type fittings used not to require anything other than friction to ensure a seal. For those who used Bunsen burners during chemistry periods the pink rubber hose from the bench top gas spigots to the Bunsen burner will recall the hose was merely a push fit. I'm going back over sixty years and happy to be corrected if things have changed significantly. I can't recall my school ever being razed to the ground, even with me in attendance. Might be worth some folks doing a spot of Googling prior to posting slightly inaccurate advice, albeit in a well meaning way. If a spigot fitting requires a clamp of any description then generally the spigot is designed with parallel sides with a pronounced lip at the end. If a "quick fix" is required on joints which are not a tight fit to a hose then use self amalgamating tape. Would further suggest not being sparing with the tape, and being careful to lap the layers by a half width and keep a tension on the tape when winding. Such tape is not just for sealing electrical joints.

@carolleenkelmann4751 Жыл бұрын

Its just so wonderfully satisfying watching David working on his Van, so aptly named, "Pandemonium". His antics give me such a feeling of "anything is possible." My self confidence rises beyond recognition and fired on by the comments on hacksaws or jigsaws and judging by eye, going back repeatedly to buy missing or non-fitting parts, I don't feel so alone and isolated facing the demoralising prospects of attacking my DIY projects.

@shirleylynch7529 Жыл бұрын

What a patience you have David. Well done. Brilliant video. Thank you letting us observe you as you work.

@Vandemonium Жыл бұрын

Thanks 👍

@optroncordian7863 Жыл бұрын

As an owner of an induction hob, I can tel you: Everithing from steel and iron works: cast iron, carbon iron, stainless steel, alpaca and so on. I even have some metal plates and they work too. Aluminum does not work at all unless it has a steel insert in the bottom. Usually they are marked as induction compatible. When you look at the bottom, you will see a steel grate - that heats it. The hob will tell you - if it cannot work with the vessel, it will show error on display.

@toronado455 Жыл бұрын

alpaca? 🤔

@rickkearn7100 Жыл бұрын

Only David could rivet his audience with such a mundane (yet rife with peril) exercise in plumbing 101! Well done sir! Cheers.

@kelvinlights1028 Жыл бұрын

Jubilee clip should have been used for the pump connection.

@Vandemonium Жыл бұрын

It shouldn't need one, the whole point of the barb thing is that it's a pressure fit

@allansheldrake4832 Жыл бұрын

@@Vandemonium a barb fitting is only good for gravity fed water systems as there is no pressure being fed to it a jubliee clam will press the pipe closer to the barb fitting creating a water tight seal

@kenwignall Жыл бұрын

I agree jubilee clip required similar barb finish on some gas connections but you wouldn't dream of just push fitting the pipe, or WOULD YOU 😳

@jenniesebrasky6023 Жыл бұрын

I'm cracking up. I'm not sure which is funnier / cleverer -- David or the comments section. What a great video.

@AndyCutright Жыл бұрын

Shifting focus off the personal canal vlogs onto other projects was a great decision. You're back to producing as much or more great canal content as you ever have. Seems like you've got a renewed vigor. Yes, I know this is the van channel 😉And of course, the van content is great too.

@pageant1fd Жыл бұрын

Please David don’t take everyone’s sound advice , I’d prefer watching your methods. Thanks for the entertainment sir !

@Vandemonium Жыл бұрын

Haha will do!

@peteraspinall3355 Жыл бұрын

Hi David Just seen the waste pipe fitting video. Why not just warm up the waste pipe at an appropriate point with a hair dryer ( a heat gun can be used but with caution 😬) and create a bend, then keep hold of it at the required angle and dip in a bucket of cold water to set the angle. Also, smear the wate pipe rubber grommet seal with washing up liquid to lubricate before fitting. It will go on further and a lot easier. The inlet pipe you fitted was not a problem with your fitting it. It was a problem with the the white plastic fitting not being seated to the pre assembled pipe properly. It should have been tested first at the factory. The water was not coming from your black warmed up pipe where it joined. Sealant may work temporarily but if twisted it may leak again. Regards Peter

@stevenjohnson4190 Жыл бұрын

What a nail-biting cliffhanger to end on. I can't wait for the next episode.

@azlandpilotcar4450 Жыл бұрын

My induction cooker came with a simple, flexible magnet like you use to hold things on the refridgerator. You are supposed to use it to check pots and pans. I also found a steel stove diffuser plate that is magnetic -- there are many on Amazon. If a pan isn't magnetic the diffuser plate can be used on top of the cooker, and works as well to heat the pan.

@Vandemonium Жыл бұрын

I will buy one, thanks

@Dmate89 Жыл бұрын

That satisfying "tump", when you squeezed the seal on the waste pipe

@davidoickle1778 Жыл бұрын

What you lack in formal training, you more than make up for with solid thinking. Kudos! As for the small leak, perhaps heat the pipe and install a small hose clamp. That's a "fickle finger of fate" thing. It's leaking because it CAN. 😅 Top marks on the diesel vent. Can’t wait to hear the report on that.

@Vandemonium Жыл бұрын

I'm pleased to report that a 160-mile round trip recently resulted in no drips from the vent!

@isobelchapman9548 Жыл бұрын

You always make me chuckle…..’if this doesn’t work I’ll sell the van’…….😅😅 Thanks again for a grand wee vlog. I was willing that darned pipe NOT to leak …….arghhh.

@linuxkidd Жыл бұрын

re: RidgeMonkey -- if a magnet sticks to it, it should work on the induction cooktop. Best of luck!

@marks-0-0 Жыл бұрын

I love Davids willingness to try stuff and how he admits it might not work, same as me, sometimes i want to see why an idea fails. I wouldn't be worried about diesel spills for the reason you state but more so a diesel smell slowly building up.

@HYUKLDER1 Жыл бұрын

Re the diesel tank ventilation issue. Usually a secondary fuel tank will have a 'fuel tank vent screw' on the top of the tank filling cap which (when unscrewed) allows air into the tank as fuel is being drawn out by the pump. This is quite normal with fuel tanks on boat outboard motors and on marine 'secondary' fuel tanks which is essentially what you have.

@lloydbaker7104 Жыл бұрын

If a magnet sticks to it then it will work with induction!

@jamesellsworth9673 Жыл бұрын

And magnetic metal 'flame-tamer' plates are readily available to transfer heat to a non-metallic pot or pan.

@22vinebrook10 Жыл бұрын

“Arrghh! I hate hacksaws!” saw-saw-wiggly-wiggly sawing… and 😮….3…2…1 Holding my breath, will there be blood flow? Yikes! 😅 Good job! 🎉 🥳

@Vandemonium Жыл бұрын

It's just like the start of an episode of "Casualty"!

@nilo70 Жыл бұрын

Always end on a cliffhanger David , that way everyone will want to see the next episode 😊 Cheers from California !

@TK-zf7sx Жыл бұрын

I second mvpeters suggestion - replace the ferrule/barb combination. I suspect the leak is at that joint, not where the hose fits over the barbs. As to the vent in the diesel canister - I would think that a vented cap would be available - one with a one-way valve, I mean.

@eastcoast4233 Жыл бұрын

Oh my, more sawing in midair 😮

@Vandemonium Жыл бұрын

🤣

@charris9959 Жыл бұрын

Sawing in midair is the funniest thing…. 🤣😂

@linz_in_NZ Жыл бұрын

Diesel tank - you can buy a purpose made Marine diesel tank with all the fittings and vents on it - Mark Davies shows one on one of his Diesel Heater videos. Water tanks - Why not have them the other way round so that the fresh water pipe goes straight up to the tap instead of the curve? Fresh water on the outside, waste on the inside?Always a good idea to clean the pipe cuts of any swarf/curly bits, as if it goes in the water tank it will get into your pump and could cause problems. Also take the stickers off the pipe that goes into your fresh water too :-)

@martinclay7557 Жыл бұрын

If you look up Ham-fisted in the dictionary there is a picture of David holding a hacksaw. 🤣

@Vandemonium Жыл бұрын

True

@philgray1023 Жыл бұрын

Hose clamps, heat guns and lubrication make portable plumbing perfect fun. If a magnet sticks to a pan, it is induction suitable.

@seanjamescameron Жыл бұрын

I'm taking notes to see how I can do this in my allotment shed.

@andrewriley1664 Жыл бұрын

'That fish in the Amazon that goes up your wee'🤣🤣

@Vandemonium Жыл бұрын

You know the one I mean!!

@LongPeter Жыл бұрын

Hacksaws work much, MUCH better if you secure the workpiece near the cut. They cut on the push so just a good corner to wedge it in is often enough. Don't try and go fast, you'll just make yourself tired. Don't push too hard, you'll just bend the blade and make it wander. Just relax, go slow and if you start to get impatient, think about something else; maybe the next thing you need to do. Also, that is a tetchy little saw. A proper, full-size one give you much more usable blade length and many more teeth through the kerf for each stroke.

@Vandemonium Жыл бұрын

👍

@dirkduester1843 Жыл бұрын

Thank you, David! Entertaining as always and there are some quotes that I have in mind as well when working on something for the first time!

@Vandemonium Жыл бұрын

Cheers!

@shaunmatthews6889 Жыл бұрын

The easiest way to check if a pot, pan or kettle can be used on an induction plate is to use a small magnet. If it sticks, the answer is yes

@fransahm1956 Жыл бұрын

Check your pans with a magnet. If it sticks it should work.

@Vandemonium Жыл бұрын

Ah yes, good point!

@trevormiddleton Жыл бұрын

None of the Ridgemonkey cooking products is suitable for induction hobs, but you can buy an induction hob adapter plate from, say, Amazon, which is basically a ferrous disc that sits between your induction hob and the non-induction pan. (I’ve been considering the same question myself!).

@marieeszenyi332 Жыл бұрын

Also, I am SO glad you didn’t saw your fingers off. 🎉

@MakeDoAndMend1 Жыл бұрын

Forgot to mention. We all learn from experience. Doing the Doing. So we'll done matey many people would have given up. The more you do diy the better you get. Cheers from old George and Jane

@stanleyromanowski9816 Жыл бұрын

Jubilee clip will fix the leak at the barbed connector.

@loki7441 Жыл бұрын

A small jubilee clip or jubbly clip as my mate calls them is the way to go if the water pipe still leaks. Wont need much pressure, keep gently tightening the clip as the pump is running, when the drip stops, quid's in. Nothing more annoying. As regards the pin hole in the handle. The diesel will probably slosh about like an old belly dancer and the most you'll get is an oily stain. Wont be the Torry Canyon in the back of the van. Oh , when your cutting with a junior hacksaw, the gap the blade makes tries, successfully to close. Used in conjunction with poly pipe you get the melting effect from the friction which causes it to become even more sticky. You may have noticed it became easier when you placed it over your knee. I stick to the senior hacksaw, not becuase I'm getting old, but its more user friendly. Especially to an apprentice senior. 😂

@ganlin1 Жыл бұрын

get a magnet see if will attach to the ridgemonkey, if it does it will work of your hob

@johnmurdock6195 Жыл бұрын

Try placing a magnet on the bottom of your ridge monkey if it sticks to the bottom, then you should have enough ferrous material to work.

@crazybull299 Жыл бұрын

A jubilee clip or pipe clamp may solve the leaking problem but there is an assumption that the leak is caused by the black pipe you have squeezed onto the barbs. It may be that the leak is coming from the metal crimped half.

@Vandemonium Жыл бұрын

It's coming from the pipe, I can see it

@kenShuttleworth Жыл бұрын

@@Vandemonium The push fit looks sufficiently tight, it looks like the leak is coming from between the metal and white nylon parts, pull the black rubber pipe back a couple of barbs so that you can see which joint is leaking. Sealant will probably not last when applied externally, rather than between the surfaces that should be mated together.

@wrinklyrider Жыл бұрын

Great video on how to do a 10 minute job in only 3 days.😅

@Vandemonium Жыл бұрын

Yep, that's my DIY

@normangibson9907 Жыл бұрын

Just about the push fit connection on the bottom of the sink. If you put a small bit of fairy liquid around the inside of the rubber connector it will slide on much easier. Still loving the van videos

@t1n4444 Жыл бұрын

Not to rain on your parade David but would suggest a brief natter with your insurers ref your modifications performed by yourself. I once contacted the BSS and boat insurers ref work on my boat. Both stated that provided the manufacturer's installation instructions/method statement were followed to the letter then they were happy. However insurers did assure me that they would check to confirm compliance. You will appreciate that's why there are "T&C's" ... for their benefit.

@dithompson2679 Жыл бұрын

I didn't read down the comments very far so I apologize if I'm repeating advice here. Always use a magnet to definitively test any cookware you want to use on an induction cooktop. If a magnet adheres to it, it will work. My husband and I (from Virginia USA) love watching your vlogs, David ... on the canals or on the roads.

@Vandemonium Жыл бұрын

Thank you

@NeverlandSystemZor Жыл бұрын

I love a plumbing video that doesn't just go down the drain! ;) Great work as always. I do miss your boat (it was a low key dream to get to the UK and stumble into you cruising the canals)... but I am glad to see the vids there showing the history and modern canal life, and these camper van vids. You're very entertaining and always inspiring with your interest, ambition, and DIY spirit. Keep up the great work!

@gafrers Жыл бұрын

Great work. Loving this "upgrade series"

@andyrbush Жыл бұрын

Super glue will wick into the water connection and seal it. The cap on the diesel tank seems to have a small nozzle designed to take a vent tube. That can be connected to the cap and run up a few inches to prevent leaks.

@gregbolitho9775 Жыл бұрын

Nice work, learned a cupla things, still trying to get mine together. Thanks m8, nice work.

@Cornovii Жыл бұрын

Soak your bendy pipes in boiling water then hold it flat whilst it cool. Hey presto! straight pipes!

@patrickhall3878 Жыл бұрын

Hello from Texas.. push on David .

@trumpetrider565 Жыл бұрын

Use a jubilee clip man!! Simple and effective!!

@kevinsanders200 Жыл бұрын

It wasn't the hacksaw. You were holding the black pipe on the wrong end. Always hold the longest end, and cut off the shortest end, while it's in the air. Don't rest the short bit on anything. If you do that from now on, you'll find the job will go much smoother. For everything you cut. Also, if you wipe some spit on the inside of the rubber hose attachment before you push it onto the sink drain, the male end, it would just slide on.

@TeeVeeZed123 Жыл бұрын

You’ll need a converter plate if you want to use your Ridge Monkey on the induction hob.

@fenrichlee2867 Жыл бұрын

As Irene says - a drop of washing up liquid works wonders on interference pipe fittings.

@matthewwakeham2206 Жыл бұрын

Here's a tip for any plastic fittings that leak. Check for a moulding line with your finger nail. The water tracks along these. You can smooth them with fine sand paper or wire wool or even a scourer. As long as any scratches you make are fine enough And run in the same direction as the sealing surface, it will work. In this case you'd wrap the barbed fitting in your abrasive and hold and turn the pipe left and right to polish out the moulding line. In addition or as an alternative you can put several turns of PTFE tape round it before pushing it together.

@0HARE Жыл бұрын

Actually pretty interesting stuff. I’m amazed by your ability to keep on going through the difficult technical fiddly bits. I really admire your camper van, and am considering building one for myself and the wife. Happy Camping

@filmmakingmad Жыл бұрын

Hello David, The bad news first and the good news second. I bought a Ridge Money for the boat fine on gas but at home on the induction hob, a big fail because the RM is made of non magnetic aluminium. Now the good news I purchased a Tescoma Induction Hob Adapter from Amazon, currently unavailable but there are other such beasts available on Amazon. The adapter works well but it must be borne in mind that the steel adapter holds the heat. Hope that helps. P.S. I had an Autoterm installed on my boat to replace the aged Mikuni.

@markwhitcher2138 Жыл бұрын

You are doing quality work. I am excited to see the places you take the viewers.

@jasonw6640 Жыл бұрын

Another fun video. I think your diesel will be just fine.

@troyw8338 Жыл бұрын

David" sealant? 😅 heat the hose with hair dryer then twist it back and forth a few times, this should seat the barbs. If not put on a wide zip tie and pull it tight with a pliers. 😊

@paulhoughton5266 Жыл бұрын

Hi David, a bit of Fairy Loquid on those push fits can help push them in further. Great video as always

@rickterry8148 Жыл бұрын

Wago connectors and wago box for your under sink connectors. Electrical retailers normally have some you can buy individually.

@Dmate89 Жыл бұрын

If a magnet likes your pan so will the hob

@bennysh Жыл бұрын

had the same problem of dripping from my hose, ended up going to the doctor. just kidding, I ended up using a hose clamp, that worked. BTW I also had trouble finding the right words for "hose clamps", so I asked chatGPT something like "what is the name of these metal rings that are used to tighten a hose?". this thing is brilliant!

@michaelshelton462 Жыл бұрын

A proper vent on the diesel tank will prevent the vacuum collapse during use but will close off when not in use to prevent odors and flammable gases from escaping. Just a thought David. Great video as always!

@alastairgordon-forbes3139 Ай бұрын

It’s outrageous. I hope you win your case.

@henrywilliam8506 Жыл бұрын

With the leak from your water pipe, why not simply use a jubilee clip? The vent in your diesel container. A very easy fix and a fuel gauge to match. If you go to a chancery and but a fuel gauge screw rap for your fuel container (a universal fit) if comes with a vent screw within the cap. About £20 max.

@Infirito_Ekra Жыл бұрын

To be fair, if the pin hole in the handle doesn't work, it'll be pretty easy to seal it back up.

@peterjones2411 Жыл бұрын

use a tie-rap or 2 jubilee clamp if you have 1 on your water pipe 😃👍 use any magnet on any pan if it stick to your pan it's suitable for induction 😉👍

@andrewjones-productions Жыл бұрын

PTFE tape and a jubilee clip will work wonders on that water pump hose connection.

@plutostar4139 Жыл бұрын

Using washing up liquid will lubricate the pipes to make the fitting a lot easier

@kentolsen7384 Жыл бұрын

BRAVO! Well done and a good recovery.

@chrisweston2017 Жыл бұрын

Enjoyed the video, very well done. Use a magnet on the cooking pan, if it sticks it'll work. The pin hole vent is likely to be too small. Assuming the van is stationery when the heater is in use, just slacken off the filler cap.

@Vandemonium Жыл бұрын

Cool, thanks

@layalabi1667 Жыл бұрын

Thank you. Hope everything works well!

@livingladolcevita7318 Жыл бұрын

Maybe a simple access hole in the supply water bottle for filling to save you undoing the pump pipe work. Constantly flexing pipes might incur leakage eventually.

@scottwallace7315 Жыл бұрын

I looked up your comment "said the actress to the bishop" and laughed. Entertaining videos as always. Thank you for sharing your adventures and thoughts with all of us. Hello from Colorado USA.

@geobolt8788 Жыл бұрын

This series reminds me of those movie series. Always ends with a cliff hanger !

@adrianheywood Жыл бұрын

Yep - you did it again; if someone had told me, even yesterday, that I'd be captivated by watching a middle-aged man with his dripping - and I quote - "stiff pipe" well, I would probably have punched them in the face. :)

@philip9657 Жыл бұрын

Surely the pin hole will allow diesel vapour out as well which will build up

@barbarataylor1535 Жыл бұрын

Love your get 'er done attitude. Cheers

@MakeDoAndMend1 Жыл бұрын

Two things. Fuel tank needs one way valve. When you stop the vehicle fuel will go one end of container. Same when you accelerate causing fuel to pop out of pin hole. Looks as if you need hose clamps. Also it looks as if the crimped water hose. Silver bit is faulty. One way valves are very low cost. Etc. Cheers from old George and Jane.

@Vandemonium Жыл бұрын

Cheers. I've done a 160 mile trip over mixed roads and absolutely nothing came out of the pinhole, phew

@edwardlong9470 Жыл бұрын

No the Ridge monkey does not work on induction, I have had the same problem, but you can buy an induction plate that will conduct the heat, but it must be solid one. Good luck.

@julese-p278 Жыл бұрын

If you put a cable tie or two on that leaking hose it will help to seal it to the barb.

@nickcollins7568 Жыл бұрын

Need to get a jubilee clip on the leaking connector. That should seal it

@centauri61032 Жыл бұрын

Just try a zip tie around that barb fitting. That little leak shouldn't take much to correct. And your diesel tank pinhole will be just fine. It won't leak or smell. You may even need to make it just a bit larger. Check the tank during operation and see if there is any sign of vacuum. Also check when the temperature in the van heats up for the tank bulging due to expansion.

@barbarawhittall2311 Жыл бұрын

Just found out that you are in a van now!! Look forward to watching you in your new adventure!!;!

@Vandemonium Жыл бұрын

Haha cheers, I've had the van for five years! I don't live in it, it's a weekend kinda thing

@alisonlee3314 Жыл бұрын

A little late to the party 😀 x

@rogermillard7290 Жыл бұрын

place a magnet under the pan, if it sticks it is ok.

@campingstoveman Жыл бұрын

Good afternoon, another amusing video, thank you. may I make a few suggestions please, when cutting plastic tube flexible or rigid either use a sharp knife or support the pipe mechanically because as you were cutting with the saw your action of pushing down caused the cut area to close up gripping the saw blade making it harder to cut, the free end of the pipe was leaning on the seat pushing up, never rely on barbs not leaking always use a suitable hose clip to clamp the pipe to the barb and finally when pushing fittings into a flexible pipe smear some vaseline around the fitting as lubrication.

@danielbaxter6203 Жыл бұрын

Stick a magnet on the pan it. If it stick it'll work. Ps I've not tried the theory even though I have an induction hob on the cooker!

@anfieldroadlayoutintheloft5204 Жыл бұрын

Good video thanks lee

@paulwhitehouse3690 Жыл бұрын

David, 1. simply put a hose clamp around the leaking pipe, 2. A pinhole vent (to allow air in) while diesel may not exit as a liquid, being a hydrocarbon will produce vapour! So the suggestion of a little one way valve was a good one!

@robg3545 Жыл бұрын

A tiny smear from a tiny 1/2oz pot of Black Swan silicone grease gets any pipe onto any connector. I couldnt help thinking of Kenny Everett's Reg Prescott character while you were hacking away at that pipe !

@Brad-.-.-.-.howitzer Жыл бұрын

Exactly right, silicone grease has many uses

@sharktripdan Жыл бұрын

I suspect it was leaking between the silver part and the nylon barbed fitting.

@Vandemonium Жыл бұрын

Well it jolly well shouldn't! 🤣

@sharktripdan Жыл бұрын

@@Vandemonium I agree but I have seen hoses leak there, you came up with a good solution to seal it.

@UKHaiku Жыл бұрын

Great video, entertaining as always! I was a little worried about the standing pipe - both because it looked like it still had a label on it, and also because it feels like the gap between the standing pipe and the flexible one could be a problem for bugs etc…

@bofor3948 Жыл бұрын

If your freshwater refil tank was identical to the supply tank (that one almost is) you could simply swap them over instead of decanting and risking spilage. I think you are probably right about the diesel not spilling from the pin prick, but i did chuckle when you said "it will only drop on the road -not ideal but not a crisis" It would be for the poor sod following you, if they hit that patch of diesel🤣

@Vandemonium Жыл бұрын

Fair point though the amount would be absolutely negligible if any, and it would first have to spill out of the tiny vent and then make its way to the gas locker hole ... I checked after a 160-mile trip on mixed roads and there wasn't even the tiniest drip escaped.

@Brad-.-.-.-.howitzer Жыл бұрын

LOL

@suedanperkins562 Жыл бұрын

For induction tops, if a magnet sticks to pan / ridge mokey it will work.

@lucodeath Жыл бұрын

Jubilee clip needed, 000 or 00 size. I would remove the waste tank and put pipe out through the bottom as its only dish water. More storage space then.

@lucodeath Жыл бұрын

A lot of vans tap into the main diesel tank for the heater. More storage and no diesel leaks and smells.