Going 7MGE-T, quick info dump on the process. I no doubt left a few things out.
Пікірлер: 64
@ImReelySuqi
Seriously can't thank you enough for this video. Everyone has a 2jz or gte video but this? This is great info. Especially for the poopra owners with the na 7m
@hornet72883 жыл бұрын
Love all the great knowledge. I ended up swapping a gte block into my n/a. So i have a spare n/a sitting in the garage. This video has me tempted to grab another shell and turbo the GE
@tedmartin1543 жыл бұрын
So useful, just got your 1000th sub. Amazing vid thank you so much.
@MultiDesignGuy3 жыл бұрын
Great video Dana i have a 7MGE Im rebuilding didn’t have guys to go T😚 i would also say i had head cryogenically treated it had gone soft my Brinell Hardness number went from 68 to 105 + ARP studs and a smidge more torque from 78 ft pound to 85ish
@jakeusan3 жыл бұрын
Picked up a non running 88 supra shell with a rebuilt 7mge ready to go in with OE CT26 and R154 swap, just need to button up motor and trans and drop her in! My first project, pretty intimidating to be honest haha.
@darrenfrancis56913 жыл бұрын
The parts are interchangeable, GTE pistons and rods can work on the ge
@Keck_YT2 жыл бұрын
Hey mate, awesome video. Info much appreciated.
@rens29983 жыл бұрын
Interesting! I wasn't aware that I could reuse the GE throttle body and ignition stuff
@jorgediaz4206914 күн бұрын
Are you putting the GE AFM before or after the turbo? I’m not sure if it’s suppose to be a blow through?
@Lowspirit_aaron
So you can get away with a rising rate on stock pressure? I planned on using the factory elbow to choke it up a little so it isn’t spiking to 10psi lol. I’ve been wanting to do this on my Cressida a while now. And I’ve pretty much got everything from owning my my mk3 Supra for years. No turbo electronics though
@daneitor973 жыл бұрын
Thanks for the info!
@ibm_businessman60332 жыл бұрын
Oh fuck yea
@Thatmc450 Жыл бұрын
Have watched this probably 20-30 times over the past 2 years, my turbo e36 in down for the count awaiting bore/stroke and missing turbo noises. Have a 7m Cressida that’s missiled out, cage, w58, xcessive steering etc. planning on just gte manifold, ct26 with internal wastegate, fmu.For ecu management and blow through maf would it break up under 5psi? I don’t care about extra power at all it drifts just fine at stock power w/ 40psi 235’s. Know this sounds absolutely pointless but I can get all the parts for less than $350 for a good laugh on track. Have looked through forums but can’t find a solid write up
@nezzydawg2 жыл бұрын
Dude this was sooo helpful: thank you for making this . The only thing I’m confused about is if I use the 7mge ecu ? Or if I need a gte ecu . How does that even work ?
@doomkid023 жыл бұрын
I got a spare ge block sitting that was considering doing a buult bottom end lol. For the oil feed, isnt it possible to just drill and tap it?
@toweringhorse20542 жыл бұрын
I have a GTE, was mostly curious with the difference between the turbo and the NA
@dolanwae27182 жыл бұрын
hey man, what electronics i need to complete going 7mgte?
@a70_s362 жыл бұрын
I got questions can I run my stock ecu safely?
@apochrea34602 жыл бұрын
hey man do you have a instagram i could contact you more directly on i was just wondering how i can clean up all the hoses and wiring to make it look as clean as your engine bay does as well as the rocker covers that you have