www.reliablehardware.com/ Detailed instruction on the use of rivets and/or screws for attaching various pieces of Road Case Hardware to your Road Case. Parts and Tools www.reliablehardware.com/diyro...
Пікірлер: 90
@chuyetax11 жыл бұрын
Thanks alot for your answer and help. Also, congratulations for this DIY, the only and the best i found around the web. thank you!!
@RetroRumble6 жыл бұрын
Just ordered some of your hardware, great video. Thanks for everything!
@reliabledan6 жыл бұрын
Thank you! We appreciate your business -
@reliabledan11 жыл бұрын
Yes chuyetax - as 3/8" wood was used for the entire project, so were 3/8" rivets. Keep in mind that if you use a different thickness of wood, say 1/4" or 1/2", you'd need to use different length rivets. Hope this helps.
@reliabledan11 жыл бұрын
Back-up washers are most important for handles, latches and any other components that are subject to strain. While it can't hurt to put back-up washers on other "passive" components it's not a priority. Hope this helps.
@FarmerJack0808112 жыл бұрын
If the inner holes of the hinges were riveted first, then washers could be used for the outer holes where there is no aluminum behind them.
@65Superhawk11 жыл бұрын
I am just wondering with all those parts, how much I can actually save building it myself. Seems like the labor is better suited to someone with air tools and a large work area.
@leofilee10 жыл бұрын
i like to built a case for 2 55 inch tv , so what material i have to buy expect plywood ??
@TheBassQuark3 ай бұрын
Hey there! Great video! Do you have guidance on how to measure and cut for the recessed clamps? I’m trying to convert 4 traditional hinges to a few twist lock clamps
@psychodad196111 жыл бұрын
No washers on the back of the corner clamp rivets?
@jomar21915 жыл бұрын
a doubt, as the tool used to press the drawer is called, which has a strap that surrounds the drawer
@juliantsa5 жыл бұрын
Cool and thanks for your help
@reliabledan5 жыл бұрын
It's always good to know that our videos helped. Thanks for watching!
@souravmandalguitar97896 жыл бұрын
nice. help full
@jasonpowell376211 жыл бұрын
"...and we'll blow off any shpilkus that might get in the way here!" ?! awesome. this guy is rad
@GoldCoastRay10 жыл бұрын
The corner ball and latches have recesses to allow for the corner angles and tongue and groove....what size corners are they? small med or large?
@tecnonayarita11803 жыл бұрын
good video thanks a question where can I buy the pieces
@TempleGuitars Жыл бұрын
Thank you for sharing! What size rivets do you recommend?
@jaygodin11 жыл бұрын
Do you guys carry something that I can make a sliding shelf with? Like the DJ cases that have sliding laptop shelves?
@djnujr.42993 жыл бұрын
What is the size of rivert for 3/4 plywood? Also the size of washer?
@chuyetax11 жыл бұрын
excuse me!! every rivet that you used, is the same 3/16 in all the road case work?
@vladtepes979 жыл бұрын
maybe it would be wise to tell customers in parts 5 and 6 to not put rivets at the ends of the extrusions so they don't get in the way of those corner pieces.
@buskinon11 жыл бұрын
Thnx for info Im starting a new job building these next week much appreciated kiwi-phill
@reliabledan11 жыл бұрын
As a matter of fact we are putting the finishing touches on a terrific NEW sliding shelf made specially for DJ's. It should be ready for sale in less than a month. Go to our web site, ReliableHardware . com and sign up on our Mailing List (upper left hand column) and you'll receive notification via an E-mail. Hope this helps.
@go2ldook6 жыл бұрын
So I am putting together parts for a custom case. For my angle extrusions, I need low profile, so using 3/4 inch ones. Other hardware, like the small ball corners and latches I have selected do not seem to have the slight recession to allow for the extrusions. Is that a problem when you put it together? Do they just bend when you rivet them?
@reliabledan6 жыл бұрын
You are correct. They are designed to bend slightly for a tight fit.
@seventyseventele12 жыл бұрын
What is the part number for the corner clamp mentioned at 1:12? I can't find them on the website.
@mattmalley4 ай бұрын
I have a 20 year-old custom guitar case and the tension gets too tight before I can completely close my latches. Is there something I can do to loosen up the tension?
@freetimefilms4 жыл бұрын
The ball corners are nice, but those are for the typical situation where the edge of the wood / corner is 90 degrees - what about if it's 45 degrees? Say I want to build an octagon box - what can I use to cover the corners?
@KidFromWinnetka4 жыл бұрын
You might call Gene @ Reliable on Monday. He may have a suggestion for you. 818-753-8558
@jwstout00712 жыл бұрын
The drill bit you are using looks like it has a stop on it, is that out of your personal collection or does it come with the pack of rivets? Now onto the real challenge... making a flight case house ;)
@RobOnekea2 жыл бұрын
The lid that I'm designing is 3 inches. I haven't picked up my pieces yet just designing it. Is 3 inches enough room for the ball corner and the 2 hole clamp? My case is a 1/4 build. Thanks!
@IronCobraPTW2 жыл бұрын
Yes
@robgracia5096 жыл бұрын
awesome
@reliabledan12 жыл бұрын
RH-0608 - thanks for asking.
@anthonyknight511410 жыл бұрын
Does the company make custom cases to order? I have a need for an amp head and 4U to 6U rack the would roughly measure 24"W x 23" H x 16" D without the lids
@reliabledan10 жыл бұрын
Anthony, We do not make cases - we make case hardware for those who do. Search for "custom road cases" in your area.
@anthonyknight511410 жыл бұрын
Thank you. With those measurements in mind, could you recommend the the amount of tongue and groove valances and right angle extrusion? Is the stuff sold in 12' and 10' pieces?
@reliabledan10 жыл бұрын
Anthony Knight You're going to need to a bit of work yourself. Start by making a sketch of your case that includes dimensions. This will aid you in determining the amount of valance, double angle extrusion and other parts you'll need. After you've done that you may certainly call and we'll help you refine your list. 800-757-5270
@pineappleexplode6 жыл бұрын
I'm putting together a shopping cart on your website to build myself a road case, but I can't find the corner clamps you use at the 1:15 mark. can you send me a link?
@reliabledan6 жыл бұрын
Hope this helps - www.reliablehardware.com/large4holeclampzinc-1.aspx
@amjaudio90642 жыл бұрын
What size of rebate?
@Benny-con-amor6 жыл бұрын
what size of corners , rivets, latches and handles did you used, Im planning to build a acoustic guitar road case. any advice of what to order will be appreciated Thank you for all your videos.
@reliabledan6 жыл бұрын
Hope this helps. www.reliablehardware.com/roadcaseschematic.aspx www.reliablehardware.com/diyroadcaseparts.aspx
@Benny-con-amor6 жыл бұрын
reliabledan thank you so much!!!
@TempleGuitars Жыл бұрын
@@reliabledan One link say's 3/8" rivets, the other says 1/4" rivets. Which one is recommended?
@audio97sonorizaciones163 жыл бұрын
Distribuidor en México ?
@TheKingOftheBlue055056 жыл бұрын
como se llama aquello que parece una pistola.??? es una herramienta pero quiero saber com se llama
@sender875 жыл бұрын
remachadora
@stevecomeau6004 жыл бұрын
I heard the size rivet to use but maybe I missed it, what length Rivets are you using?
@KidFromWinnetka4 жыл бұрын
The rivet length depends on the thickness of the wood. Fow example, if your wood is 3/8" use 3/8" rivets. www.reliablehardware.com/poprivets.aspx
@beachndude657 жыл бұрын
How far apart are the rivets supposed to be on the double angle extrusion?
@reliabledan7 жыл бұрын
Every 12 to 18 inches is ideal.
@beachndude657 жыл бұрын
Thanks, I'm building a lighting console road case :) I'll be in tomorrow for some more double angle :)
@reliabledan7 жыл бұрын
Great - see you tomorrow.
@LostBushcrafter2 жыл бұрын
about the ball corner clamp rivets at 1:06 - aren't you just riveting into wood with no backup washers? Won't that just crush the plywood?
@LostBushcrafter2 жыл бұрын
also the latches at 3:12?
@JoseRivera-xo6zc5 жыл бұрын
Where I can get all the material to bill one of those cases Info please Thank you
@reliabledan5 жыл бұрын
www.ReliableHardware.com
@meransashaira50423 жыл бұрын
Can i ask what kind of hinges is that what do you called that hinge ? Thanks for the answer
@KidFromWinnetka3 жыл бұрын
All hinges are here. Scroll down to Large Stop Hinge. www.reliablehardware.com/hinges.aspx
@akbrodarsgorakhpuri36945 жыл бұрын
Perfect
@reliabledan5 жыл бұрын
Thank you!
@electronic.murahcahaya.tek52765 жыл бұрын
Good joob...he he he
@que4radioboard8133 жыл бұрын
where can i get some of those stop latches??
@IronCobraPTW2 жыл бұрын
Tch
@tubeswampy12 жыл бұрын
This video was riveting.
@yuniormendez59534 жыл бұрын
What size drill bit is needed to drill the holes for the rivets ?
@KidFromWinnetka4 жыл бұрын
#11 drill.
@yuniormendez59534 жыл бұрын
Do you have the link cause the one I can find on Lowe’s is a 11/64
You are using to many rivets with your hybrid. Also those extra base rivets shoud be in line with your lid rivets. Why are you not using bar clamps ? It's like basic and much better than a belt. Overall not a really good job...
@reliabledan12 жыл бұрын
:-)
@rahultiwaridj32375 жыл бұрын
15 inch 4 top ka cabinet 2 15 inch bass cabinet him KO chahiye apka number chahiye humko
@adelrobiyyuu98195 жыл бұрын
Li
@tomthompson74003 жыл бұрын
the rivets on the lid and the case dont line up ,,, why not ? 0:27 lid rivets in the way of the balls ,,, its only half thought out , you need to plan ahead more ,,, still if its still gigging eight years on , who cares , its the only one of us that is.