Episode 846 This only requires one resistor and one capacitor for a clock circuit. I also try the jitter measurement mode on the Rigol MSO5000. Is the 567 12 better than the 555 Be a Patron: / imsaiguy
Пікірлер: 36
@Kirillissimus2 жыл бұрын
If you just need to generate some squarewave then there is an even simpler way: LM3909 LED blinker IC. No need for the extra resistor, just add a capacitor, hook up the power, add a bunch of wires and it just works. Although in the modern era when even a toilet brush can not hit the market without a WiFi or Bluetooth connection, an iPhone and Android app, a few blinking LEDs and a buzzer in the handle and a contactless charger in the base station to constantly put some juice in the batteries that would power all the necessary luxuries, I would probably just use an ATtiny MCU and programmed everything including the frequency in. The solution would not require any external components at all to just do its job and it would allow for external digital control that will no doubt be required in the future.
@davidharms35622 жыл бұрын
Great video! Thanks for sharing the knowledge! I didn’t know about this ic.
@chupathingy5862 Жыл бұрын
This thing would be great for a 440hz tone generator. Thanks for the idea!
@ruhnet3 жыл бұрын
Wow I always just thought it was only a DTMF decoder chip. Very cool other stuff it does, too!
@argcargv3 жыл бұрын
Cool chip. Note you can get a 555 to generate a clock with a single resistor and a capacitor by placing the resistor between the output and the trigger+threshold pins. This trick works better with the cmos version which has rail to rail output. I am not sure what that hack does to the jitter and stability. The bipolar version probably has some temperature dependence in the output rails which would probably degrade the performance.
@vincei42523 жыл бұрын
National Semiconductor wrote some of the most excellent datasheets and application notes. I regret leaving all mine behind when I moved from the UK to the US in the 90's. I was reminded of this when I clicked on the LM567 Ti datasheet on Digikey and it pulled up a copy of the datasheet written by National Semiconductor. RIP.
@IMSAIGuy3 жыл бұрын
yes they did. I still have my copy of the linear app notes
@vincei42523 жыл бұрын
@@IMSAIGuy Nice. I put a link to Ti datasheet but it looks like KZfaq deleted it. shrug. Site gets worse by the day.
@suncrafterspielt94793 жыл бұрын
would be great some internal explanation and the differences to the 555
@PeetHobby Жыл бұрын
Only the 567 cost much more(three times or so), the low cost is why we use mostly the 555 and not timer/clock ICs. And they are not as widely available as the 555.
@gyrgrls Жыл бұрын
I loved the 3909 before they vanished into obsolescence.
@blackarrow86832 жыл бұрын
Thank you! Can you also do an eye diagram with that scope?
@IMSAIGuy2 жыл бұрын
Yes, you can trigger on both edges and turn up the persistence
@frankowalker46623 жыл бұрын
What's the jitter level at >1.2 seconds ? I'm looking for a reliable timer circuit.
@odissey23 жыл бұрын
Timing is RC-controlled. So it's stability is 3-5% at best.
@absurdengineering11 ай бұрын
@@odissey2 With NP0 caps and low-tempco resistors? It's not that bad as long as the supply voltage is regulated.
@t1d1003 жыл бұрын
I have been looking at how to create a 60Hz sine wave. I know you are creating a square wave, but can the 567 be configured to go that slowly, reliably and with decent precision?
@IMSAIGuy3 жыл бұрын
no
@odissey23 жыл бұрын
Best way to produce 60Hz sine, stable and accurate, is by using a DDS generator. You can find AD9833 online for
@IMSAIGuy3 жыл бұрын
@@odissey2 that requires a microcontroller and firmware also
@odissey23 жыл бұрын
@@IMSAIGuythat what it takes for "slow, decent and reliable" 60Hz sine. The magic frequency (60Hz) assumes 10-4 frequency stability and decent THD specs. The alternative is XTAL-divider-double integrator-filter will be probably not cost effective and surely worse THD
@odissey23 жыл бұрын
@@IMSAIGuy a uC can be used to emulate slow DDS output, such as 60Hz sine. If uC has a DAC and a XTAL, it can be accomplished without external DDS
@braveheart52802 жыл бұрын
IS IT NORMAL FOR THE OSC FREQUENCY TO CHANGE WITH SMALL POWER SUPPLY VOLTAGE CHANGES.
@IMSAIGuy2 жыл бұрын
yes
@braveheart52802 жыл бұрын
@@IMSAIGuy THANKS
@jstro-hobbytech2 жыл бұрын
What brand resistors are you using?
@IMSAIGuy2 жыл бұрын
those are old soviet
@jstro-hobbytech2 жыл бұрын
@@IMSAIGuy nice. Ever watch diodegonewild? He has so much old soviet everything all tesla brand haha